On Tue, Aug 27, 2019 at 05:43:59PM +0530, Amit Kucheria wrote:
> Printing the function name when enabling debugging makes logs easier to
> read.
>
> Signed-off-by: Amit Kucheria <amit.kucheria@xxxxxxxxxx>
> Reviewed-by: Stephen Boyd <swboyd@xxxxxxxxxxxx>
> Reviewed-by: Daniel Lezcano <daniel.lezcano@xxxxxxxxxx>
This should need to be manually added at each call site; it is already
built into the logging system (the f flag for dynamic debug)?
Daniel.
> ---
> drivers/thermal/qcom/tsens-common.c | 8 ++++----
> drivers/thermal/qcom/tsens.c | 6 +++---
> 2 files changed, 7 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index c037bdf92c663..7437bfe196e50 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -42,8 +42,8 @@ void compute_intercept_slope(struct tsens_priv *priv, u32 *p1,
>
> for (i = 0; i < priv->num_sensors; i++) {
> dev_dbg(priv->dev,
> - "sensor%d - data_point1:%#x data_point2:%#x\n",
> - i, p1[i], p2[i]);
> + "%s: sensor%d - data_point1:%#x data_point2:%#x\n",
> + __func__, i, p1[i], p2[i]);
>
> priv->sensor[i].slope = SLOPE_DEFAULT;
> if (mode == TWO_PT_CALIB) {
> @@ -60,7 +60,7 @@ void compute_intercept_slope(struct tsens_priv *priv, u32 *p1,
> priv->sensor[i].offset = (p1[i] * SLOPE_FACTOR) -
> (CAL_DEGC_PT1 *
> priv->sensor[i].slope);
> - dev_dbg(priv->dev, "offset:%d\n", priv->sensor[i].offset);
> + dev_dbg(priv->dev, "%s: offset:%d\n", __func__, priv->sensor[i].offset);
> }
> }
>
> @@ -209,7 +209,7 @@ int __init init_common(struct tsens_priv *priv)
> if (ret)
> goto err_put_device;
> if (!enabled) {
> - dev_err(dev, "tsens device is not enabled\n");
> + dev_err(dev, "%s: device not enabled\n", __func__);
> ret = -ENODEV;
> goto err_put_device;
> }
> diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> index 542a7f8c3d962..06c6bbd69a1a7 100644
> --- a/drivers/thermal/qcom/tsens.c
> +++ b/drivers/thermal/qcom/tsens.c
> @@ -127,7 +127,7 @@ static int tsens_probe(struct platform_device *pdev)
> of_property_read_u32(np, "#qcom,sensors", &num_sensors);
>
> if (num_sensors <= 0) {
> - dev_err(dev, "invalid number of sensors\n");
> + dev_err(dev, "%s: invalid number of sensors\n", __func__);
> return -EINVAL;
> }
>
> @@ -156,7 +156,7 @@ static int tsens_probe(struct platform_device *pdev)
>
> ret = priv->ops->init(priv);
> if (ret < 0) {
> - dev_err(dev, "tsens init failed\n");
> + dev_err(dev, "%s: init failed\n", __func__);
> return ret;
> }
>
> @@ -164,7 +164,7 @@ static int tsens_probe(struct platform_device *pdev)
> ret = priv->ops->calibrate(priv);
> if (ret < 0) {
> if (ret != -EPROBE_DEFER)
> - dev_err(dev, "tsens calibration failed\n");
> + dev_err(dev, "%s: calibration failed\n", __func__);
> return ret;
> }
> }
> --
> 2.17.1
>
