On Friday, June 21, 2019 10:59:08 AM CEST Vinod Koul wrote: > This series add support for Renesas USB controllers uPD720201 and uPD720202. > These require firmware to be loaded and in case devices have ROM those can > also be programmed if empty. If ROM is programmed, it runs from ROM as well. > > This includes two patches from Christian which supported these controllers > w/o ROM and later my patches for ROM support and multiple firmware versions. > > Changes in v2: > used macros for timeout count and delay > removed renesas_fw_alive_check > cleaned renesas_fw_callback > removed recurion for renesas_fw_download > added MODULE_FIRMWARE > added comment for multiple fw order > > Christian Lamparter (2): > usb: xhci: add firmware loader for uPD720201 and uPD720202 w/o ROM > usb: xhci: handle uPD720201 and uPD720202 w/o ROM > > Vinod Koul (3): > usb: xhci: Use register defined and field names > usb: xhci: Add ROM loader for uPD720201 > usb: xhci: allow multiple firmware versions > > drivers/usb/host/xhci-pci.c | 942 ++++++++++++++++++++++++++++++++++++ > 1 file changed, 942 insertions(+) > bootlog from a Netgear WNDR4700 with a 32GiB USB3 Stick attached to the Renesas uPD720202K8-711-BAA-A chip. [ 13.523094] xhci_hcd 0000:45:00.0: firmware size is not a multiple of 8. [ 13.868071] xhci_hcd 0000:45:00.0: xHCI Host Controller [ 13.873325] xhci_hcd 0000:45:00.0: new USB bus registered, assigned bus number 2 [ 13.886296] xhci_hcd 0000:45:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x0000000101000090 [ 13.902719] usbcore: registered new interface driver usb-storage [ 13.909277] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 13.917336] hub 2-0:1.0: USB hub found [ 13.921432] init: - preinit - [ 13.930356] hub 2-0:1.0: 2 ports detected [ 13.942869] xhci_hcd 0000:45:00.0: xHCI Host Controller [ 13.948122] xhci_hcd 0000:45:00.0: new USB bus registered, assigned bus number 3 [ 13.955514] xhci_hcd 0000:45:00.0: Host supports USB 3.0 SuperSpeed [ 13.981227] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 13.997141] hub 3-0:1.0: USB hub found [ 14.004375] hub 3-0:1.0: 2 ports detected [ 14.375644] usb-storage 1-1:1.0: USB Mass Storage device detected [ 14.382247] scsi host1: usb-storage 1-1:1.0 [ 14.438959] usb 3-2: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd [ 14.467746] usb-storage 3-2:1.0: USB Mass Storage device detected [ 14.474241] scsi host2: usb-storage 3-2:1.0 [ 15.394562] scsi 1:0:0:0: Direct-Access Generic STORAGE DEVICE 9454 PQ: 0 ANSI: 0 [ 15.405183] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 15.522448] scsi 2:0:0:0: Direct-Access SanDisk Ultra 1.00 PQ: 0 ANSI: 6 [ 15.531952] sd 2:0:0:0: [sdb] 60063744 512-byte logical blocks: (30.8 GB/28.6 GiB) [ 15.541007] sd 2:0:0:0: [sdb] Write Protect is off [ 15.546808] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 15.574567] sdb: sdb1 [ 15.580581] sd 2:0:0:0: [sdb] Attached SCSI removable disk This is working. Tested-by: Christian Lamparter <chunkeey@xxxxxxxxx>
