On 2/4/19 10:03, Mark Brown wrote:
> On Mon, Jan 28, 2019 at 12:45:03PM +0100, Jorge Ramirez-Ortiz wrote:
>
>> @@ -653,6 +708,10 @@ spmi_regulator_find_range(struct spmi_regulator *vreg)
>> range = vreg->set_points->range;
>> end = range + vreg->set_points->count;
>>
>> + /* we know we only have one range for this type */
>> + if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_HFS430)
>> + return range;
>> +
>> spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, &range_sel, 1);
>>
>> for (; range < end; range++)
>
> Rather than have special casing for the logical type in here it seems
> better to just provide a specific op for this logical type, you could
> always make _find_range() call into that one if you really want code
> reuse here. You already have separate ops for this regulator type
> anyway.
sorry I dont quite understand your point.
static struct regulator_ops spmi_hfs430_ops = {
/* always on regulators */
.set_voltage_sel = spmi_regulator_hfs430_set_voltage, *
.set_voltage_time_sel = spmi_regulator_set_voltage_time_sel, *
.get_voltage = spmi_regulator_hfs430_get_voltage,
.map_voltage = spmi_regulator_common_map_voltage, *
.list_voltage = spmi_regulator_common_list_voltage,
.get_mode = spmi_regulator_hfs430_get_mode,
.set_mode = spmi_regulator_hfs430_set_mode,
};
find_range affects the functions above with *
You are right and I can easily adjust the private
spmi_regulator_hfs430_set_voltage. And since it is quite small I can
also _duplicate_ the common function spmi_regulator_set_voltage_time_sel
with a small change for hfs430.
But spmi_regulator_common_map_voltage ends up being a large function and
I dont see the point in replicating it to save the "if" statement above.
why cant different logical_types extend spmi_regulator_find_range(..)?
Or maybe are you saying that I should add a new interface to struct
spmi_regulator that implements priv_find_range(..) for the logical types
that dont want to use the common implementation?
But also I am not sure I see the benefits with respect to the proposed
change...
>
>> +static unsigned int spmi_regulator_hfs430_get_mode(struct regulator_dev *rdev)
>> +{
>> + struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
>> + u8 reg;
>> + int ret;
>> +
>> + ret = spmi_vreg_read(vreg, SPMI_HFS430_REG_MODE, ®, 1);
>> + if (ret) {
>> + dev_err(&rdev->dev, "failed to get mode");
>> + return ret;
>> + }
>> +
>> + if (reg == SPMI_HFS430_MODE_PWM)
>> + return REGULATOR_MODE_NORMAL;
>> +
>> + return REGULATOR_MODE_IDLE;
>> +}
>
> I'd have expected a switch statement here, ideally flagging a warning or
> error if we get a surprising value in there.
this implementation follows what the common function
spmi_regulator_common_get_mode implements (ie, checks for a case and
defaults if that is not the one; and when defaulting, there is no
reporting that it is actually defaulting: ie, defaulting is not being
interpreted as an error..should it?)
>
>> +static int spmi_regulator_hfs430_set_mode(struct regulator_dev *rdev,
>> + unsigned int mode)
>> +{
>> + struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
>> + u8 reg = mode == REGULATOR_MODE_NORMAL ? SPMI_HFS430_MODE_PWM :
>> + SPMI_HFS430_MODE_AUTO;
>
> Please write a normal if statement (or switch statement) to help
> legibility.
>
ok.
