On Fri, Jan 25, 2019 at 03:45:09PM -0800, Bjorn Andersson wrote:
> The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, add these to
> the platform dtsi and enable them for the EVB with the perst gpio
> and analog supplies defined.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 25 +++++++++
> arch/arm64/boot/dts/qcom/qcs404.dtsi | 67 ++++++++++++++++++++++++
> 2 files changed, 92 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> index 50b3589c7f15..579ddaf4f5fa 100644
> --- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> @@ -21,6 +21,22 @@
> };
> };
>
> +&pcie {
> + status = "ok";
> +
> + perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&perst_state>;
> +};
> +
> +&pcie_phy {
> + status = "ok";
> +
> + vdda-vp-supply = <&vreg_l3_1p05>;
> + vdda-vph-supply = <&vreg_l5_1p8>;
> +};
> +
> &remoteproc_adsp {
> status = "ok";
> };
> @@ -137,6 +153,15 @@
> };
>
> &tlmm {
> + perst_state: perst {
> + pins = "gpio43";
> + function = "gpio";
> +
> + drive-strength = <2>;
> + bias-disable;
> + output-low;
> + };
> +
> sdc1_on: sdc1-on {
> clk {
> pins = "sdc1_clk";
> diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> index 76699435c8bd..7b219865ba7e 100644
> --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> @@ -3,6 +3,7 @@
>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,gcc-qcs404.h>
> +#include <dt-bindings/gpio/gpio.h>
>
> / {
> interrupt-parent = <&intc>;
> @@ -377,6 +378,7 @@
> compatible = "qcom,gcc-qcs404";
> reg = <0x01800000 0x80000>;
> #clock-cells = <1>;
> + #reset-cells = <1>;
>
> assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>;
> assigned-clock-rates = <19200000>;
> @@ -405,6 +407,21 @@
> #interrupt-cells = <4>;
> };
>
> + pcie_phy: phy@7786000 {
> + compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
> + reg = <0x07786000 0xb8>;
> +
> + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
> + resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
> + <&gcc GCC_PCIE_0_PIPE_ARES>;
> + reset-names = "phy", "pipe";
> +
> + clock-output-names = "pcie_0_pipe_clk";
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> sdcc1: sdcc@7804000 {
> compatible = "qcom,sdhci-msm-v5";
> reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
> @@ -771,6 +788,56 @@
> status = "disabled";
> };
> };
> +
> + pcie: pci@10000000 {
> + compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
> + reg = <0x10000000 0xf1d
> + 0x10000f20 0xa8
> + 0x07780000 0x2000
> + 0x10001000 0x2000>;
> + reg-names = "dbi", "elbi", "parf", "config";
> + device_type = "pci";
> + linux,pci-domain = <0>;
Since we only have single PCIe controller,
I don't think we need to specify a pci-domain.
With that:
Reviewed-by: Niklas Cassel <niklas.cassel@xxxxxxxxxx>
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + ranges = <0x81000000 0 0 0x10003000 0 0x00010000 /* I/O */
> + 0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
> +
> + interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> + clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_0_AUX_CLK>,
> + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
> + clock-names = "iface", "aux", "master_bus", "slave_bus";
> +
> + resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
> + <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
> + <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
> + <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
> + <&gcc GCC_PCIE_0_BCR>,
> + <&gcc GCC_PCIE_0_AHB_ARES>;
> + reset-names = "axi_m",
> + "axi_s",
> + "axi_m_sticky",
> + "pipe_sticky",
> + "pwr",
> + "ahb";
> +
> + phys = <&pcie_phy>;
> + phy-names = "pciephy";
> +
> + status = "disabled";
> + };
> };
>
> timer {
> --
> 2.18.0
>
