On 12/7/2018 8:13 AM, Jeffrey Hugo wrote:
On 12/7/2018 7:23 AM, Marc Gonzalez wrote:
On 06/12/2018 23:11, Jeffrey Hugo wrote:
Add rpm smd clocks, PMIC and bus clocks which are required on MSM8998
for clients to vote on.
Signed-off-by: Jeffrey Hugo <jhugo@xxxxxxxxxxxxxx>
---
v2
-fix compatible ordering nits per Stephen
.../devicetree/bindings/clock/qcom,rpmcc.txt | 1 +
drivers/clk/qcom/clk-smd-rpm.c | 62
++++++++++++++++++++++
include/dt-bindings/clock/qcom,rpmcc.h | 6 +++
3 files changed, 69 insertions(+)
Hmmm, my board seems to dislike this patch... it locks up for a while,
then reboots.
[ 6.957289] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending
flag query for idn 1 failed, err = -11
[ 6.961233] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag_retry:
failed with error -11, retries 2
[ 6.970782] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag_retry:
query attribute, opcode 6, idn 1, failed with error -11 after 3 retires
[ 6.979576] ufshcd-qcom 1da4000.ufshc: ufshcd_complete_dev_init
setting fDeviceInit flag failed with error -11
[ 23.432798] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 23.432884] rcu: 7-...0: (1 GPs behind)
idle=6a2/1/0x4000000000000000 softirq=92/93 fqs=2626
[ 23.437927] rcu: (detected by 0, t=5252 jiffies, g=-819, q=112)
[ 23.446425] Task dump for CPU 7:
[ 23.452567] swapper/0 R running task 0 1 0
0x0000002a
[ 23.455806] Call trace:
[ 23.462872] __switch_to+0x94/0xe0
[ 23.465009] _regmap_write+0x58/0xb0
[ 23.468452] _regmap_update_bits+0xf0/0x110
[ 23.472186] regmap_update_bits_base+0x60/0x90
[ 23.476110] clk_disable_regmap+0x34/0x40
[ 23.480614] clk_branch_toggle+0x108/0x1b0
[ 23.484681] clk_branch2_disable+0x18/0x20
[ 23.488692] clk_disable_unused_subtree+0xc4/0xe0
[ 23.492761] clk_disable_unused+0x3c/0x130
[ 23.497535] do_one_initcall+0x5c/0x180
[ 23.501557] kernel_init_freeable+0x198/0x244
[ 23.505276] kernel_init+0x10/0x110
[ 23.509768] ret_from_fork+0x10/0x20
/*** REBOOT ***/
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
I need to check the ufs_reset pin and phy init seq before I can
investigate
this issue, but I wanted to send a report ASAP.
Hmm. I run with clk_ignore_unused. I'm guessing that something was
defined that should be used eventually, but isn't used now, and so its
getting turned off when it probably shouldn't be.
I'll try to repro on my end.
I think I figured this out.
The issue appears to be with the mmssnoc_axi_rpm_clk that this patch
defines. Removing that, and I do not observe a crash. This clock will
eventually be needed for the multimedia subsystem (camera and the like).
Marc, it would be good if you could comment out this clock to verify my
observations translate to your setup.
The problem occurs when the rpm driver, during probe, sends the active
settings to the rpm. This causes the rpm to try to access the mmss over
the relevant config noc, and results in an unclocked bus error, which is
a fatal error.
clk_ignore_unused avoids this issue because it leaves on the config noc
clock defined in gcc - gcc_mmss_noc_cfg_ahb_clk
I can see 3 workarounds to this issue -
1. comment out mmssnoc_axi_rpm_clk with an explanation to why, and leave
this problem to whomever needs the clock in the future
2. add the CLK_IGNORE_UNUSED flag to gcc_mmss_noc_cfg_ahb_clk so prevent
it from being disabled (aka a selective version of clk_ignore_unused)
3. add a prepare_enable call to gcc_mmss_noc_cfg_ahb_clk in the gcc
probe, so that there is always one active consumer of the clock (this is
what downstream does)
Stephen, do you have a preference, or an alternative suggestion?
--
Jeffrey Hugo
Qualcomm Datacenter Technologies as an affiliate of Qualcomm
Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the
Code Aurora Forum, a Linux Foundation Collaborative Project.
