This patch removes support for the APQ8064 based Arrow SD600 eval
board. This board was never sold publicly and had very limited
distribution. As such, we are removing this board and no longer
going to support it.
Signed-off-by: Andy Gross <andy.gross@xxxxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 -
.../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 53 ---
.../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 ---------------------
3 files changed, 469 deletions(-)
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d..00d6e65 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
ox820-cloudengines-pogoplug-series-3.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8060-dragonboard.dtb \
- qcom-apq8064-arrow-sd-600eval.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
deleted file mode 100644
index 8df7315..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
+++ /dev/null
@@ -1,53 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-&tlmm_pinmux {
- card_detect: card-detect {
- mux {
- pins = "gpio26";
- function = "gpio";
- bias-disable;
- };
- };
-
- pcie_pins: pcie-pinmux {
- mux {
- pins = "gpio27";
- function = "gpio";
- };
- conf {
- pins = "gpio27";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- user_leds: user-leds {
- mux {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- };
-
- conf {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- output-low;
- };
- };
-
- magneto_pins: magneto-pins {
- mux {
- pins = "gpio31", "gpio48";
- function = "gpio";
- bias-disable;
- };
- };
-};
-
-&pm8921_mpps {
- mpp_leds: mpp-leds {
- pinconf {
- pins = "mpp7", "mpp8";
- function = "digital";
- output-low;
- };
- };
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
deleted file mode 100644
index 76b56ea..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ /dev/null
@@ -1,415 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-
-/ {
- model = "Arrow Electronics, APQ8064 SD_600eval";
- compatible = "arrow,sd_600eval", "qcom,apq8064";
-
- aliases {
- serial0 = &gsbi7_serial;
- serial1 = &gsbi1_serial;
- i2c0 = &gsbi2_i2c;
- i2c1 = &gsbi3_i2c;
- i2c2 = &gsbi4_i2c;
- i2c3 = &gsbi7_i2c;
- spi0 = &gsbi5_spi;
- };
-
- regulators {
- compatible = "simple-bus";
- vph: regulator-fixed@1 {
- compatible = "regulator-fixed";
- regulator-min-microvolt = <4500000>;
- regulator-max-microvolt = <4500000>;
- regulator-name = "VPH";
- regulator-type = "voltage";
- regulator-boot-on;
- };
-
- /* on board fixed 3.3v supply */
- vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- };
-
- hdmi-out {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_con: endpoint {
- remote-endpoint = <&hdmi_out>;
- };
- };
- };
-
- soc {
- rpm@108000 {
- regulators {
- vdd_s1-supply = <&vph>;
- vdd_s2-supply = <&vph>;
- vdd_s3-supply = <&vph>;
- vdd_s4-supply = <&vph>;
- vdd_s5-supply = <&vph>;
- vdd_s6-supply = <&vph>;
- vdd_s7-supply = <&vph>;
- vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
- vdd_l3_l15_l17-supply = <&vph>;
- vdd_l4_l14-supply = <&vph>;
- vdd_l5_l8_l16-supply = <&vph>;
- vdd_l6_l7-supply = <&vph>;
- vdd_l9_l11-supply = <&vph>;
- vdd_l10_l22-supply = <&vph>;
- vdd_l21_l23_l29-supply = <&vph>;
- vdd_l24-supply = <&pm8921_s1>;
- vdd_l25-supply = <&pm8921_s1>;
- vdd_l26-supply = <&pm8921_s7>;
- vdd_l27-supply = <&pm8921_s7>;
- vdd_l28-supply = <&pm8921_s7>;
- vin_lvs1_3_6-supply = <&pm8921_s4>;
- vin_lvs2-supply = <&pm8921_s1>;
- vin_lvs4_5_7-supply = <&pm8921_s4>;
-
- s1 {
- regulator-always-on;
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- };
-
- s2 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
- regulator-always-on;
- };
-
- s3 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- qcom,switch-mode-frequency = <4800000>;
- };
-
- s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <1600000>;
- qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
- bias-pull-down;
- regulator-always-on;
- };
-
- s7 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <3200000>;
- };
-
- l3 {
- regulator-min-microvolt = <3050000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
-
- l4 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
-
- l5 {
- regulator-min-microvolt = <2750000>;
- regulator-max-microvolt = <3000000>;
- bias-pull-down;
- regulator-boot-on;
- regulator-always-on;
- };
-
- l6 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- bias-pull-down;
- };
-
- /**
- * 1.8v required on LS expansion
- * for mezzanine boards
- */
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- l23 {
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- bias-pull-down;
- };
-
- lvs6 {
- bias-pull-down;
- };
-
- lvs7 {
- bias-pull-down;
- };
- };
- };
-
- gsbi@12440000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_UART_W_FC>;
- serial@12450000 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi1_uart_4pins>;
- };
- };
-
- gsbi@12480000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@124a0000 {
- /* On Low speed expansion and Sensors */
- label = "LS-I2C0";
- status = "okay";
- lis3mdl_mag@1e {
- compatible = "st,lis3mdl-magn";
- reg = <0x1e>;
- vdd-supply = <&vcc3v3>;
- vddio-supply = <&pm8921_s4>;
- pinctrl-names = "default";
- pinctrl-0 = <&magneto_pins>;
- interrupt-parent = <&tlmm_pinmux>;
-
- st,drdy-int-pin = <2>;
- interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
- <31 IRQ_TYPE_EDGE_RISING>; /* INT */
- };
- };
- };
-
- gsbi@16200000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@16280000 {
- /* On Low speed expansion */
- status = "okay";
- label = "LS-I2C1";
- clock-frequency = <200000>;
- eeprom@52 {
- compatible = "atmel,24c128";
- reg = <0x52>;
- pagesize = <64>;
- };
- };
- };
-
- gsbi@16300000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c@16380000 {
- /* On High speed expansion */
- label = "HS-CAM-I2C3";
- status = "okay";
- };
- };
-
- gsbi@1a200000 {
- status = "okay";
- spi@1a280000 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
- };
- };
-
- /* DEBUG UART */
- gsbi@16600000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
- serial@16640000 {
- label = "LS-UART0";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi7_uart_2pins>;
- };
-
- i2c@16680000 {
- /* On High speed expansion */
- status = "okay";
- label = "HS-CAM-I2C2";
- };
- };
-
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&user_leds>, <&mpp_leds>;
-
- compatible = "gpio-leds";
-
- user-led0 {
- label = "user0-led";
- gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- user-led1 {
- label = "user1-led";
- gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- user-led2 {
- label = "user2-led";
- gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- user-led3 {
- label = "user3-led";
- gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- };
-
- wifi-led {
- label = "WiFi-led";
- gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- bt-led {
- label = "BT-led";
- gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- pci@1b500000 {
- status = "okay";
- vdda-supply = <&pm8921_s3>;
- vdda_phy-supply = <&pm8921_lvs6>;
- vdda_refclk-supply = <&vcc3v3>;
- pinctrl-0 = <&pcie_pins>;
- pinctrl-names = "default";
- perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
- };
-
- phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- target-supply = <&pm8921_lvs7>;
- };
-
- /* OTG */
- usb@12500000 {
- status = "okay";
- dr_mode = "peripheral";
- ulpi {
- phy {
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l4>;
- };
- };
- };
-
- usb@12520000 {
- status = "okay";
- dr_mode = "otg";
- ulpi {
- phy {
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
- };
- };
-
- usb@12530000 {
- status = "okay";
- dr_mode = "otg";
- ulpi {
- phy {
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
- };
- };
-
- amba {
- /* eMMC */
- sdcc@12400000 {
- status = "okay";
- vmmc-supply = <&pm8921_l5>;
- vqmmc-supply = <&pm8921_s4>;
- };
-
- /* External micro SD card */
- sdcc@12180000 {
- status = "okay";
- vmmc-supply = <&pm8921_l6>;
- pinctrl-names = "default";
- pinctrl-0 = <&card_detect>;
- cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
- };
-
- riva-pil@3204000 {
- status = "okay";
-
- pinctrl-names = "default";
- pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
- };
-
- hdmi-tx@4a00000 {
- status = "okay";
- core-vdda-supply = <&pm8921_hdmi_switch>;
- hdmi-mux-supply = <&vcc3v3>;
-
- hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
-
- ports {
- port@1 {
- endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
-
- hdmi-phy@4a00400 {
- status = "okay";
- core-vdda-supply = <&pm8921_hdmi_switch>;
- };
-
- mdp@5100000 {
- status = "okay";
-
- ports {
- port@3 {
- endpoint {
- remote-endpoint = <&hdmi_in>;
- };
- };
- };
- };
- };
-};
--
2.7.4
