On Tue, Nov 06, 2018 at 05:35:28PM +0530, Balakrishna Godavarthi wrote:
> [ 176.929612] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
> [ 176.945734] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
> [ 176.953298] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
> [ 177.010660] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
> [ 177.067633] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
>
> The above errors log on console due to receiving of stray bytes
> when wcn3990 boot up's i.e. when during initial setup procedure.
Please shortly introduce the topic instead of starting with the log
messages.
> Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> ---
> drivers/bluetooth/hci_qca.c | 20 +++++++++++++++++++-
> 1 file changed, 19 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index 97b57e0f4725..341f80606574 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -56,6 +56,7 @@
>
> /* Controller states */
> #define STATE_IN_BAND_SLEEP_ENABLED 1
> +#define STATE_DISCARD_RX 2
>
> #define IBS_WAKE_RETRANS_TIMEOUT_MS 100
> #define IBS_TX_IDLE_TIMEOUT_MS 2000
> @@ -511,6 +512,7 @@ static int qca_open(struct hci_uart *hu)
> } else {
> hu->init_speed = qcadev->init_speed;
> hu->oper_speed = qcadev->oper_speed;
> + set_bit(STATE_DISCARD_RX, &qca->flags);
> ret = qca_power_setup(hu, true);
> if (ret) {
> destroy_workqueue(qca->workqueue);
> @@ -903,6 +905,13 @@ static int qca_recv(struct hci_uart *hu, const void *data, int count)
> if (!test_bit(HCI_UART_REGISTERED, &hu->flags))
> return -EUNATCH;
>
> + /* We discard Rx data received while device is in booting
> + * stage, this is due multiple baudrate switch is causing
> + * UART to read some garbage data.
> + */
This isn't entirely correct. I saw frame reassembly errors before
qca_wcn3990_init() is called, i.e. no baudrate changes. Some of the
garbage seems to be sent shortly after powering on the controller.
> + if (test_bit(STATE_DISCARD_RX, &qca->flags))
> + return 0;
> +
> qca->rx_skb = h4_recv_buf(hu->hdev, qca->rx_skb, data, count,
> qca_recv_pkts, ARRAY_SIZE(qca_recv_pkts));
> if (IS_ERR(qca->rx_skb)) {
> @@ -1192,10 +1201,12 @@ static int qca_setup(struct hci_uart *hu)
> set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
> clear_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
> hu->hdev->shutdown = qca_power_off;
> +
> ret = qca_wcn3990_init(hu);
> if (ret)
> return ret;
>
> + clear_bit(STATE_DISCARD_RX, &qca->flags);
> ret = qca_read_soc_version(hdev, &soc_ver);
> if (ret)
> return ret;
> @@ -1278,8 +1289,15 @@ static void qca_power_shutdown(struct hci_uart *hu)
> struct serdev_device *serdev = hu->serdev;
> unsigned char cmd = QCA_WCN3990_POWEROFF_PULSE;
>
> - host_set_baudrate(hu, 2400);
> + /* From this point we go into power off state,
> + * disable IBS and discard all the queued data.
> + */
> + clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
> + set_bit(STATE_DISCARD_RX, &qca->flags);
> + qca_flush(hu);
> +
> hci_uart_set_flow_control(hu, true);
> + host_set_baudrate(hu, 2400);
> serdev_device_write(serdev, &cmd, sizeof(cmd), 0);
> serdev_device_wait_until_sent(serdev, 0);
> hci_uart_set_flow_control(hu, false);
This change won't win a beauty price, but it seems it is needed to
suppress the 'frame reassembly' spam, unless the controller can be
convinced to stop sending garbage in the first place.
Tested-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
