This adds nodes for all possible UARTs to sdm845.dtsi. By default
only configure the RX/TX lines with pinctrl. Boards that use UARTs
with flow control can overwrite the configuration in the
<board>.dtsi.
Signed-off-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
Reviewed-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
---
Changes in v2:
- use GCC_QUPV3_WRAP1_Sx_CLK for uart8-15, not
GCC_QUPV3_WRAP0_Sx_CLK
---
arch/arm64/boot/dts/qcom/sdm845.dtsi | 270 +++++++++++++++++++++++++++
1 file changed, 270 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index 0c9a2aa6a1b5..c4056c2c3cc5 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -286,6 +286,17 @@
status = "disabled";
};
+ uart0: serial@880000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x880000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c1: i2c@884000 {
compatible = "qcom,geni-i2c";
reg = <0x884000 0x4000>;
@@ -312,6 +323,17 @@
status = "disabled";
};
+ uart1: serial@884000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x884000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart1_default>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c2: i2c@888000 {
compatible = "qcom,geni-i2c";
reg = <0x888000 0x4000>;
@@ -338,6 +360,17 @@
status = "disabled";
};
+ uart2: serial@888000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x888000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart2_default>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c3: i2c@88c000 {
compatible = "qcom,geni-i2c";
reg = <0x88c000 0x4000>;
@@ -364,6 +397,17 @@
status = "disabled";
};
+ uart3: serial@88c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x88c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart3_default>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c4: i2c@890000 {
compatible = "qcom,geni-i2c";
reg = <0x890000 0x4000>;
@@ -390,6 +434,17 @@
status = "disabled";
};
+ uart4: serial@890000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x890000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart4_default>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c5: i2c@894000 {
compatible = "qcom,geni-i2c";
reg = <0x894000 0x4000>;
@@ -416,6 +471,17 @@
status = "disabled";
};
+ uart5: serial@894000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x894000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart5_default>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c6: i2c@898000 {
compatible = "qcom,geni-i2c";
reg = <0x898000 0x4000>;
@@ -442,6 +508,17 @@
status = "disabled";
};
+ uart6: serial@898000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x898000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart6_default>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c7: i2c@89c000 {
compatible = "qcom,geni-i2c";
reg = <0x89c000 0x4000>;
@@ -467,6 +544,17 @@
#size-cells = <0>;
status = "disabled";
};
+
+ uart7: serial@89c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x89c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart7_default>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
};
qupv3_id_1: geniqup@ac0000 {
@@ -506,6 +594,17 @@
status = "disabled";
};
+ uart8: serial@a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0xa80000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart8_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c9: i2c@a84000 {
compatible = "qcom,geni-i2c";
reg = <0xa84000 0x4000>;
@@ -569,6 +668,17 @@
status = "disabled";
};
+ uart10: serial@a88000 {
+ compatible = "qcom,geni-uart";
+ reg = <0xa88000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart10_default>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c11: i2c@a8c000 {
compatible = "qcom,geni-i2c";
reg = <0xa8c000 0x4000>;
@@ -595,6 +705,17 @@
status = "disabled";
};
+ uart11: serial@a8c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0xa8c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart11_default>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c12: i2c@a90000 {
compatible = "qcom,geni-i2c";
reg = <0xa90000 0x4000>;
@@ -621,6 +742,17 @@
status = "disabled";
};
+ uart12: serial@a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0xa90000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart12_default>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c13: i2c@a94000 {
compatible = "qcom,geni-i2c";
reg = <0xa94000 0x4000>;
@@ -647,6 +779,17 @@
status = "disabled";
};
+ uart13: serial@a94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0xa94000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart13_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c14: i2c@a98000 {
compatible = "qcom,geni-i2c";
reg = <0xa98000 0x4000>;
@@ -673,6 +816,17 @@
status = "disabled";
};
+ uart14: serial@a98000 {
+ compatible = "qcom,geni-uart";
+ reg = <0xa98000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart14_default>;
+ interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c15: i2c@a9c000 {
compatible = "qcom,geni-i2c";
reg = <0xa9c000 0x4000>;
@@ -698,6 +852,17 @@
#size-cells = <0>;
status = "disabled";
};
+
+ uart15: serial@a9c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0xa9c000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart15_default>;
+ interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
};
tcsr_mutex_regs: syscon@1f40000 {
@@ -954,12 +1119,117 @@
};
};
+ qup_uart0_default: qup-uart0-default {
+ pinmux {
+ pins = "gpio2", "gpio3";
+ function = "qup0";
+ };
+ };
+
+ qup_uart1_default: qup-uart1-default {
+ pinmux {
+ pins = "gpio19", "gpio20";
+ function = "qup1";
+ };
+ };
+
+ qup_uart2_default: qup-uart2-default {
+ pinmux {
+ pins = "gpio29", "gpio30";
+ function = "qup2";
+ };
+ };
+
+ qup_uart3_default: qup-uart3-default {
+ pinmux {
+ pins = "gpio43", "gpio44";
+ function = "qup3";
+ };
+ };
+
+ qup_uart4_default: qup-uart4-default {
+ pinmux {
+ pins = "gpio91", "gpio92";
+ function = "qup4";
+ };
+ };
+
+ qup_uart5_default: qup-uart5-default {
+ pinmux {
+ pins = "gpio87", "gpio88";
+ function = "qup5";
+ };
+ };
+
+ qup_uart6_default: qup-uart6-default {
+ pinmux {
+ pins = "gpio47", "gpio48";
+ function = "qup6";
+ };
+ };
+
+ qup_uart7_default: qup-uart7-default {
+ pinmux {
+ pins = "gpio95", "gpio96";
+ function = "qup7";
+ };
+ };
+
+ qup_uart8_default: qup-uart8-default {
+ pinmux {
+ pins = "gpio67", "gpio68";
+ function = "qup8";
+ };
+ };
+
qup_uart9_default: qup-uart9-default {
pinmux {
pins = "gpio4", "gpio5";
function = "qup9";
};
};
+
+ qup_uart10_default: qup-uart10-default {
+ pinmux {
+ pins = "gpio53", "gpio54";
+ function = "qup10";
+ };
+ };
+
+ qup_uart11_default: qup-uart11-default {
+ pinmux {
+ pins = "gpio33", "gpio34";
+ function = "qup11";
+ };
+ };
+
+ qup_uart12_default: qup-uart12-default {
+ pinmux {
+ pins = "gpio51", "gpio52";
+ function = "qup12";
+ };
+ };
+
+ qup_uart13_default: qup-uart13-default {
+ pinmux {
+ pins = "gpio107", "gpio108";
+ function = "qup13";
+ };
+ };
+
+ qup_uart14_default: qup-uart14-default {
+ pinmux {
+ pins = "gpio31", "gpio32";
+ function = "qup14";
+ };
+ };
+
+ qup_uart15_default: qup-uart15-default {
+ pinmux {
+ pins = "gpio83", "gpio84";
+ function = "qup15";
+ };
+ };
};
tsens0: thermal-sensor@c263000 {
--
2.19.0.605.g01d371f741-goog
