Re: [PATCH v6 3/5] thermal: qcom-spmi: Use PMIC thermal stage 2 for critical trip points

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Tue, Jul 31, 2018 at 11:59 AM, Matthias Kaehlcke <mka@xxxxxxxxxxxx> wrote:
> There are three thermal stages defined in the PMIC:
>
> stage 1: warning
> stage 2: system should shut down
> stage 3: emergency shut down
>
> By default the PMIC assumes that the OS isn't doing anything and thus
> at stage 2 it does a partial PMIC shutdown and at stage 3 it kills
> all power. When switching between thermal stages the PMIC generates an
> interrupt which is handled by the driver. The partial PMIC shutdown at
> stage 2 can be disabled by software, which allows the OS to initiate a
> shutdown at stage 2 with a thermal zone configured accordingly.
>
> If a critical trip point is configured in the thermal zone the driver
> adjusts the stage 1-3 temperature thresholds to (closely) match the
> critical temperature with a stage 2 threshold (125/130/135/140 °C).
> If a suitable match is found the partial shutdown at stage 2 is
> disabled. If for some reason the system doesn't shutdown at stage 2
> the emergency shutdown at stage 3 kicks in.
>
> The partial shutdown at stage 2 remains enabled in these cases:
> - no critical trip point defined
> - the temperature of the critical trip point is < 125°C
> - the temperature of the critical trip point is > 140°C and no
>   ADC channel is configured (thus the OS is not notified when the critical
>   temperature is reached)
>
> Suggested-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
> Signed-off-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
> ---
> Changes in v6:
> - fixed condition to check if ADC is configured in
>   qpnp_tm_update_critical_trip_temp()
> - changed °C in logs to C
> - removed needless evaluation of qpnp_tm_write() return value in
>   qpnp_tm_update_critical_trip_temp()
> - move assignment of chip->initialized to true to qpnp_tm_init(),
>   where the lock is held
> - call thermal_zone_device_update() after initialization is
>   completed
> - split some #define + comment in two lines to avoid exceeding
>   chars per line limit
> - removed extra closing parenthesis in qpnp_tm_get_temp()
> - remove unnecessary parentheses around conditions in
>   qpnp_tm_update_critical_trip_temp() and qpnp_tm_get_critical_trip_temp()
> - fixed indentation of call devm_thermal_zone_of_sensor_register() call
>   in qpnp_tm_probe()
>
> Changes in v5:
> - patch added to the series
> ---
>  drivers/thermal/qcom-spmi-temp-alarm.c | 158 ++++++++++++++++++++++---
>  1 file changed, 140 insertions(+), 18 deletions(-)

I won't claim to have spent too much time in the thermal framework,
but from what I can tell everything looks supergreat now.  FWIW:

Reviewed-by: Douglas Anderson <dianders@xxxxxxxxxxxx>

One minor comment I'd have is that I personally would have ordered
this in the series before the patch ("dt-bindings: thermal:
qcom-spmi-temp-alarm: Improve thermal zone in example") just because
that patch only really makes sense after this one lands.  ...but I
don't think it's terribly important.


-Doug




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux