Hi Balakrishna,
only two minor comments, though I hate to make you respin once more
for nits. I also noticed a possible error in the DT bindings, so maybe
you'd have to respin anyway ...
On Thu, Aug 02, 2018 at 06:55:18PM +0530, Balakrishna Godavarthi wrote:
> Add support to set voltage/current of various regulators
> to power up/down Bluetooth chip wcn3990.
>
> Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> ---
> Changes in v12:
> * removed retrying iteration loop in qca_wcn3990_init.
>
> Changes in v11:
> * removed support to read regulator currents from dts.
> * updated review comments.
>
> Changes in v10:
> * added support to read regulator currents from dts.
> * added support to try to connect with chip if it fails to respond to initial commands
> * updated review comments.
>
> changes in v9:
> * moved flow control to vendor and set_baudarte functions.
> * removed parent regs.
>
> changes in v8:
> * closing qca buffer, if qca_power_setup fails
> * chnaged ibs start timer function call location.
> * updated review comments.
>
> changes in v7:
> * addressed review comments.
>
> changes in v6:
> * Hooked up qca_power to qca_serdev.
> * renamed all the naming inconsistency functions with qca_*
> * leveraged common code of ROME for wcn3990.
> * created wrapper functions for re-usable blocks.
> * updated function of _*regulator_enable and _*regualtor_disable.
> * removed redundant comments and functions.
> * addressed review comments.
>
> Changes in v5:
> * updated regulator vddpa min_uV to 1304000.
> * addressed review comments.
>
> Changes in v4:
> * Segregated the changes of btqca from hci_qca
> * rebased all changes on top of bluetooth-next.
> * addressed review comments.
>
> ---
> drivers/bluetooth/btqca.h | 3 +
> drivers/bluetooth/hci_qca.c | 404 +++++++++++++++++++++++++++++++-----
> 2 files changed, 360 insertions(+), 47 deletions(-)
>
> diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
> index a9c2779f3e07..0c01f375fe83 100644
> --- a/drivers/bluetooth/btqca.h
> +++ b/drivers/bluetooth/btqca.h
> @@ -37,6 +37,9 @@
> #define EDL_TAG_ID_HCI (17)
> #define EDL_TAG_ID_DEEP_SLEEP (27)
>
> +#define QCA_WCN3990_POWERON_PULSE 0xFC
> +#define QCA_WCN3990_POWEROFF_PULSE 0xC0
> +
> enum qca_bardrate {
> QCA_BAUDRATE_115200 = 0,
> QCA_BAUDRATE_57600,
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index a6e7d38ef931..24ce42babe6d 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
>
> ...
>
> +static int qca_wcn3990_init(struct hci_uart *hu, u32 *soc_ver)
> +{
> + struct hci_dev *hdev = hu->hdev;
> + int ret;
> +
> + /* Forcefully enable wcn3990 to enter in to boot mode. */
> + host_set_baudrate(hu, 2400);
> + ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWEROFF_PULSE);
> + if (ret)
> + return ret;
> +
> + qca_set_speed(hu, QCA_INIT_SPEED);
> + ret = qca_send_power_pulse(hdev, QCA_WCN3990_POWERON_PULSE);
> + if (ret)
> + return ret;
> +
> + /* Wait for 100 ms for SoC to boot */
> + msleep(100);
> +
> + /* Now the device is in ready state to communicate with host.
> + * To sync host with device we need to reopen port.
> + * Without this, we will have RTS and CTS synchronization
> + * issues.
> + */
> + serdev_device_close(hu->serdev);
> + ret = serdev_device_open(hu->serdev);
> + if (ret) {
> + bt_dev_err(hu->hdev, "failed to open port");
> + return ret;
> + }
> +
> + hci_uart_set_flow_control(hu, false);
> + ret = qca_read_soc_version(hdev, soc_ver);
> +
> + return ret;
return qca_read_soc_version(hdev, soc_ver);
> +static int qca_power_setup(struct hci_uart *hu, bool on)
> +{
> + struct qca_vreg *vregs;
> + struct regulator_bulk_data *vreg_bulk;
> + struct qca_serdev *qcadev;
> + int i, num_vregs, ret = 0;
> +
> + qcadev = serdev_device_get_drvdata(hu->serdev);
> + if (!qcadev || !qcadev->bt_power || !qcadev->bt_power->vreg_data ||
> + !qcadev->bt_power->vreg_bulk)
> + return -EINVAL;
> +
> + vregs = qcadev->bt_power->vreg_data->vregs;
> + vreg_bulk = qcadev->bt_power->vreg_bulk;
> + num_vregs = qcadev->bt_power->vreg_data->num_vregs;
> + BT_DBG("on: %d", on);
> + if (on && !qcadev->bt_power->vregs_on) {
Remove extra blank after 'on'
Other than that:
Reviewed-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
Thanks for following through!
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
