On Tue, 17 Jul 2018 04:41:54 -0400
Brian Masney <masneyb@xxxxxxxxxxxxx> wrote:
> This patch adds support for optionally reading the prox_diode and
> prox_power settings from device tree. This was tested using a LG
> Nexus 5 (hammerhead) which requires a different diode than the driver
> default for the IR LED.
>
> Signed-off-by: Brian Masney <masneyb@xxxxxxxxxxxxx>
I think we can make this binding more 'generic' as right now
the amstaos bindings aren't even general enough to apply
to future amstaos devices that need a similar binding.
I'm always anti defines rather than real values in DT (where
possible) and I think there is no reason not to use real values
here.
Jonathan
> ---
> The next patch in the series removes the tsl2772 driver from the
> trivial-devices.txt file. I separated it out so that change can go
> through device tree.
>
> .../devicetree/bindings/iio/light/tsl2772.txt | 39 +++++++++++++++++++
> drivers/iio/light/tsl2772.c | 16 ++++++++
> include/dt-bindings/iio/amstaos,tsl2772.h | 24 ++++++++++++
> 3 files changed, 79 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/light/tsl2772.txt
> create mode 100644 include/dt-bindings/iio/amstaos,tsl2772.h
>
> diff --git a/Documentation/devicetree/bindings/iio/light/tsl2772.txt b/Documentation/devicetree/bindings/iio/light/tsl2772.txt
> new file mode 100644
> index 000000000000..ab553d52b9fc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/light/tsl2772.txt
> @@ -0,0 +1,39 @@
> +* AMS/TAOS ALS and proximity sensor
> +
> +Required properties:
> +
> + - compatible: Should be one of
> + "amstaos,tsl2571"
> + "amstaos,tsl2671"
> + "amstaos,tmd2671"
> + "amstaos,tsl2771"
> + "amstaos,tmd2771"
> + "amstaos,tsl2572"
> + "amstaos,tsl2672"
> + "amstaos,tmd2672"
> + "amstaos,tsl2772"
> + "amstaos,tmd2772"
> + - reg: the I2C address of the device
> +
> +Optional properties:
> +
> + - amstaos,prox_diode - must be TSL2772_DIODE0, TSL2772_DIODE1, or
> + TSL2772_DIODE_BOTH.
> + - amstaos,prox_power - must be TSL2772_100_mA, TSL2772_50_mA, TSL2772_25_mA,
> + or TSL2772_13_mA.
> + - interrupt-parent: should be the phandle for the interrupt controller
> + - interrupts: the sole interrupt generated by the device
> +
> + Refer to interrupt-controller/interrupts.txt for generic interrupt client
> + node bindings.
> +
> +Example:
> +
> +#include <dt-bindings/iio/amstaos,tsl2772.h>
> +
> +tsl2772@39 {
> + compatible = "amstaos,tsl2772";
> + reg = <0x39>;
> + interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
> + amstaos,prox_diode = <TSL2772_DIODE0>;
> +};
> diff --git a/drivers/iio/light/tsl2772.c b/drivers/iio/light/tsl2772.c
> index 34d42a2504c9..0be57f2ecb02 100644
> --- a/drivers/iio/light/tsl2772.c
> +++ b/drivers/iio/light/tsl2772.c
> @@ -515,6 +515,18 @@ static int tsl2772_get_prox(struct iio_dev *indio_dev)
> return ret;
> }
>
> +#ifdef CONFIG_OF
> +static void tsl2772_parse_dt(struct tsl2772_chip *chip)
> +{
> + struct device_node *of_node = chip->client->dev.of_node;
> +
> + of_property_read_u32(of_node, "amstaos,prox_diode",
> + &chip->settings.prox_diode);
> + of_property_read_u32(of_node, "amstaos,prox_power",
> + &chip->settings.prox_power);
> +}
> +#endif
> +
> /**
> * tsl2772_defaults() - Populates the device nominal operating parameters
> * with those provided by a 'platform' data struct or
> @@ -541,6 +553,10 @@ static void tsl2772_defaults(struct tsl2772_chip *chip)
> memcpy(chip->tsl2772_device_lux,
> tsl2772_default_lux_table_group[chip->id],
> TSL2772_DEFAULT_TABLE_BYTES);
> +
> +#ifdef CONFIG_OF
> + tsl2772_parse_dt(chip);
> +#endif
> }
>
> /**
> diff --git a/include/dt-bindings/iio/amstaos,tsl2772.h b/include/dt-bindings/iio/amstaos,tsl2772.h
> new file mode 100644
> index 000000000000..ad6f9fbc0845
> --- /dev/null
> +++ b/include/dt-bindings/iio/amstaos,tsl2772.h
> @@ -0,0 +1,24 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Device driver for monitoring ambient light intensity (lux)
> + * and proximity (prox) within the TAOS TSL2772 family of devices.
> + *
> + * Copyright (c) 2012 TAOS Corporation.
> + * Copyright (c) 2017-2018 Brian Masney <masneyb@xxxxxxxxxxxxx>
> + */
> +
> +#ifndef _DT_BINDINGS_AMSTAOS_TSL2772_H
> +#define _DT_BINDINGS_AMSTAOS_TSL2772_H
> +
> +/* Proximity diode to use */
> +#define TSL2772_DIODE0 0x01
> +#define TSL2772_DIODE1 0x02
> +#define TSL2772_DIODE_BOTH 0x03
Can we have two separate parameters to enable them?
> +
> +/* LED Power */
> +#define TSL2772_100_mA 0x00
> +#define TSL2772_50_mA 0x01
> +#define TSL2772_25_mA 0x02
> +#define TSL2772_13_mA 0x03
I'd like to see real numbers rather than defines. List the valid
values in the binding then match them to register addresses in the
driver.
A different instance of this binding for a different taos device
might have different values that are valid.
> +
> +#endif /* _DT_BINDINGS_AMSTAOS_TSL2772_H */
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
