Hi,
On 2018-06-29 16:33, Matthias Kaehlcke wrote:
Hi,
not a full review, just two nits I noticed when glacing over the first
lines, and more importantly a regression wrt v1 I found while testing.
On Thu, Jun 28, 2018 at 11:30:37AM -0700, Siddartha Mohanadoss wrote:
This patch adds support for QCOM SPMI PMIC5 family
of ADC driver that supports hardware based offset and
gain compensation. The ADC peripheral can measure both
voltage and current channels whose input signal is
connected to the PMIC ADC AMUX.
The register set and configuration has been refreshed
compared to the prior QCOM PMIC ADC family. Register
ADC5 as part of the IIO framework.
Signed-off-by: Siddartha Mohanadoss <smohanad@xxxxxxxxxxxxxx>
---
drivers/iio/adc/Kconfig | 20 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/qcom-spmi-adc5.c | 878
+++++++++++++++++++++++++++++++++++++
drivers/iio/adc/qcom-vadc-common.c | 230 +++++++++-
drivers/iio/adc/qcom-vadc-common.h | 56 +++
5 files changed, 1180 insertions(+), 5 deletions(-)
create mode 100644 drivers/iio/adc/qcom-spmi-adc5.c
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 28a9423..9533a82 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -56,6 +56,7 @@ obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
obj-$(CONFIG_QCOM_VADC_COMMON) += qcom-vadc-common.o
obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
+obj-$(CONFIG_QCOM_SPMI_ADC5) += qcom-spmi-adc5.o
In general this file uses alphabetical ordering, though the QCOM
drivers don't respect that. Still no reason to continue with the
tradition, best insert this one before CONFIG_QCOM_SPMI_IADC.
Sure, will add it before CONFIG_QCOM_SPMI_IADC.
diff --git a/drivers/iio/adc/qcom-spmi-adc5.c
b/drivers/iio/adc/qcom-spmi-adc5.c
new file mode 100644
index 0000000..75308df
--- /dev/null
+++ b/drivers/iio/adc/qcom-spmi-adc5.c
@@ -0,0 +1,878 @@
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/log2.h>
Move 'log2.h' to it's position in alphabetical order, i.e. after
'kernel.h'
Ok.
+static int adc5_get_dt_data(struct adc5_chip *adc, struct device_node
*node)
+{
+ const struct adc_channels *adc_chan;
+ struct iio_chan_spec *iio_chan;
+ struct adc5_channel_prop prop;
+ struct device_node *child;
+ unsigned int index = 0;
+ const struct of_device_id *id;
+ const struct adc_data *data;
+ int ret;
+
+ adc->nchannels = of_get_available_child_count(node);
+ if (!adc->nchannels)
+ return -EINVAL;
+
+ adc->iio_chans = devm_kcalloc(adc->dev, adc->nchannels,
+ sizeof(*adc->iio_chans), GFP_KERNEL);
+ if (!adc->iio_chans)
+ return -ENOMEM;
+
+ adc->chan_props = devm_kcalloc(adc->dev, adc->nchannels,
+ sizeof(*adc->chan_props), GFP_KERNEL);
+ if (!adc->chan_props)
+ return -ENOMEM;
+
+ iio_chan = adc->iio_chans;
+ id = of_match_node(adc5_match_table, node);
+ if (id)
+ data = id->data;
+ else
+ data = &data_pmic5;
+ adc->data = data;
+
+ for_each_available_child_of_node(node, child) {
+ ret = adc5_get_dt_channel_data(adc, &prop, child, data);
+ if (ret) {
+ of_node_put(child);
+ return ret;
+ }
+
+ prop.scale_fn_type =
+ data->adc_chans[prop.channel].scale_fn_type;
+ adc->chan_props = ∝
I suppose this intends to address Jonathan's comment about array
access vs pointer arithmetics on v1.
However it overwrites the address of the memory we allocated above
with the address of the stack object 'prop'.
Thanks for the catch. Will fix this.
You probably want to create a chan_props pointer and change the
assignment to:
*chan_props = prop;
+ adc_chan = &data->adc_chans[prop.channel];
+
+ iio_chan->channel = prop.channel;
+ iio_chan->datasheet_name = prop.datasheet_name;
+ iio_chan->extend_name = prop.datasheet_name;
+ iio_chan->info_mask_separate = adc_chan->info_mask;
+ iio_chan->type = adc_chan->type;
+ iio_chan->address = index;
+ iio_chan++;
+ adc->chan_props++;
And this changes the pointer in the adc object. I think you want to do:
chan_props++;
Cheers
Matthias
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
