On Wed, Jun 27, 2018 at 10:22:30AM +0530, Rajendra Nayak wrote:
> Add DT bindings to describe the rpm/rpmh power domains found on Qualcomm
> Technologies, Inc. SoCs. These power domains communicate a performance
> state to RPM/RPMh, which then translates it into corresponding voltage on a
> PMIC rail.
>
> Signed-off-by: Rajendra Nayak <rnayak@xxxxxxxxxxxxxx>
> Signed-off-by: Viresh Kumar <viresh.kumar@xxxxxxxxxx>
> Reviewed-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
> ---
> .../devicetree/bindings/power/qcom,rpmpd.txt | 146 ++++++++++++++++++
> include/dt-bindings/power/qcom-rpmpd.h | 39 +++++
> 2 files changed, 185 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> create mode 100644 include/dt-bindings/power/qcom-rpmpd.h
>
> diff --git a/Documentation/devicetree/bindings/power/qcom,rpmpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> new file mode 100644
> index 000000000000..8825080afa5a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/power/qcom,rpmpd.txt
> @@ -0,0 +1,146 @@
> +Qualcomm RPM/RPMh Power domains
> +
> +For RPM/RPMh Power domains, we communicate a performance state to RPM/RPMh
> +which then translates it into a corresponding voltage on a rail
> +
> +Required Properties:
> + - compatible: Should be one of the following
> + * qcom,msm8996-rpmpd: RPM Power domain for the msm8996 family of SoC
> + * qcom,sdm845-rpmhpd: RPMh Power domain for the sdm845 family of SoC
> + - power-domain-cells: number of cells in Power domain specifier
> + must be 1.
> + - operating-points-v2: Phandle to the OPP table for the Power domain.
> + Refer to Documentation/devicetree/bindings/power/power_domain.txt
> + and Documentation/devicetree/bindings/opp/qcom-opp.txt for more details
> +
> +Refer to <dt-bindings/power/qcom-rpmpd.h> for the level values for
> +various OPPs for different platforms as well as Power domain indexes
> +
> +Example: rpmh power domain controller and OPP table
> +
> +#include <dt-bindings/power/qcom-rpmhpd.h>
> +
> +qcom,level values specified in the OPP tables for RPMh power domains
> +should use the RPMH_REGULATOR_LEVEL_* constants from
> +<dt-bindings/power/qcom-rpmhpd.h>
> +
> + rpmhpd: power-controller {
> + compatible = "qcom,sdm845-rpmhpd";
> + #power-domain-cells = <1>;
> + operating-points-v2 = <&rpmhpd_opp_table>;
> + };
> +
> + rpmhpd_opp_table: opp-table {
> + compatible = "operating-points-v2-qcom-level";
> +
> + rpmhpd_opp_ret: opp1 {
> + qcom,level = <RPMH_REGULATOR_LEVEL_RETENTION>;
> + };
I don't see the point in using the OPP binding here when you aren't
using *any* of the properties from it.
Rob
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
