On 2018-06-20 04:41, Bjorn Andersson wrote:
On Tue 19 Jun 04:13 PDT 2018, Kiran Gunda wrote:
Rename the PM8941* references as WLED3 to make the
driver generic and have WLED support for other PMICs.
Looks good, just three minor comments below.
Signed-off-by: Kiran Gunda <kgunda@xxxxxxxxxxxxxx>
---
drivers/video/backlight/qcom-wled.c | 248
++++++++++++++++++------------------
1 file changed, 125 insertions(+), 123 deletions(-)
diff --git a/drivers/video/backlight/qcom-wled.c
b/drivers/video/backlight/qcom-wled.c
index 0b6d219..812f3cb 100644
--- a/drivers/video/backlight/qcom-wled.c
+++ b/drivers/video/backlight/qcom-wled.c
@@ -18,77 +18,79 @@
#include <linux/regmap.h>
/* From DT binding */
-#define PM8941_WLED_DEFAULT_BRIGHTNESS 2048
+#define WLED_DEFAULT_BRIGHTNESS 2048
-#define PM8941_WLED_REG_VAL_BASE 0x40
-#define PM8941_WLED_REG_VAL_MAX 0xFFF
+#define WLED3_SINK_REG_BRIGHT_MAX 0xFFF
+#define WLED3_CTRL_REG_VAL_BASE 0x40
-#define PM8941_WLED_REG_MOD_EN 0x46
-#define PM8941_WLED_REG_MOD_EN_BIT BIT(7)
-#define PM8941_WLED_REG_MOD_EN_MASK BIT(7)
+/* WLED3 control registers */
+#define WLED3_CTRL_REG_MOD_EN 0x46
+#define WLED3_CTRL_REG_MOD_EN_BIT BIT(7)
+#define WLED3_CTRL_REG_MOD_EN_MASK BIT(7)
-#define PM8941_WLED_REG_SYNC 0x47
These are in address order, any reason why WLED3_SINK_REG_SYNC moved
down?
Actually, this is a sink specific register. That's why moved it to
under the /* WLED3 sink specific registers */
-#define PM8941_WLED_REG_SYNC_MASK 0x07
-#define PM8941_WLED_REG_SYNC_LED1 BIT(0)
-#define PM8941_WLED_REG_SYNC_LED2 BIT(1)
-#define PM8941_WLED_REG_SYNC_LED3 BIT(2)
-#define PM8941_WLED_REG_SYNC_ALL 0x07
-#define PM8941_WLED_REG_SYNC_CLEAR 0x00
+#define WLED3_CTRL_REG_FREQ 0x4c
+#define WLED3_CTRL_REG_FREQ_MASK 0x0f
-#define PM8941_WLED_REG_FREQ 0x4c
-#define PM8941_WLED_REG_FREQ_MASK 0x0f
+#define WLED3_CTRL_REG_OVP 0x4d
+#define WLED3_CTRL_REG_OVP_MASK 0x03
-#define PM8941_WLED_REG_OVP 0x4d
-#define PM8941_WLED_REG_OVP_MASK 0x03
+#define WLED3_CTRL_REG_ILIMIT 0x4e
+#define WLED3_CTRL_REG_ILIMIT_MASK 0x07
-#define PM8941_WLED_REG_BOOST 0x4e
-#define PM8941_WLED_REG_BOOST_MASK 0x07
+/* WLED3 sink registers */
+#define WLED3_SINK_REG_SYNC 0x47
+#define WLED3_SINK_REG_SYNC_MASK 0x07
+#define WLED3_SINK_REG_SYNC_LED1 BIT(0)
+#define WLED3_SINK_REG_SYNC_LED2 BIT(1)
+#define WLED3_SINK_REG_SYNC_LED3 BIT(2)
+#define WLED3_SINK_REG_SYNC_ALL 0x07
+#define WLED3_SINK_REG_SYNC_CLEAR 0x00
[..]
-struct pm8941_wled_config {
- u32 i_boost_limit;
+struct wled_config {
+ u32 boost_i_limit;
u32 ovp;
u32 switch_freq;
u32 num_strings;
- u32 i_limit;
+ u32 string_i_limit;
Changing the members in this struct seems unrelated.
Changed the members, to have resemblance with the IPCAT and
better readability .
bool cs_out_en;
bool ext_gen;
bool cabc_en;
};
[..]
-MODULE_DESCRIPTION("pm8941 wled driver");
+MODULE_DESCRIPTION("qcom wled driver");
I would prefer if this was "Qualcomm WLED driver".
Sure. I will change it in the next series.
MODULE_LICENSE("GPL v2");
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
