HI Matthias,
Pls find my comments inline.
On 2018-05-29 23:11, Matthias Kaehlcke wrote:
On Thu, May 24, 2018 at 09:30:51PM +0530, Balakrishna Godavarthi wrote:
Add support to set voltage/current of various regulators
to power up/down Bluetooth chip wcn3990.
Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
---
Changes in v6:
* Hooked up qca_power to qca_serdev.
* renamed all the naming inconsistency functions with qca_*
* leveraged common code of ROME for wcn3990.
* created wrapper functions for re-usable blocks.
* updated function of _*regulator_enable and _*regualtor_disable.
* removed redundant comments and functions.
* addressed review comments.
Changes in v5:
* updated regulator vddpa min_uV to 1304000.
* addressed review comments.
Changes in v4:
* Segregated the changes of btqca from hci_qca
* rebased all changes on top of bluetooth-next.
* addressed review comments.
---
...
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index cb1034998040..e235be0e5202 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
...
+static void qca_set_init_speed(struct hci_uart *hu)
+{
+ unsigned int speed = 0;
- /* Setup initial baudrate */
- speed = 0;
if (hu->init_speed)
speed = hu->init_speed;
else if (hu->proto->init_speed)
@@ -946,29 +1015,136 @@ static int qca_setup(struct hci_uart *hu)
if (speed)
host_set_baudrate(hu, speed);
+}
+
+static int qca_set_operating_speed(struct hci_uart *hu, u32
*qca_baudrate)
+{
This is a bit convoluted, with the function setting the speed and
returning it. I would suggest a qca_get_oper_speed() and
qca_get_init_speed(), and just have them return the value instead of
passing it through a pointer. You could then have a qca_set_speed()
which converts the baudrate to the value the chip understands, calls
qca_set_baudrate() and host_set_baudrate()
[Bala]: will update.
+static int qca_setup(struct hci_uart *hu)
+{
+ struct hci_dev *hdev = hu->hdev;
+ struct qca_data *qca = hu->priv;
+ struct qca_serdev *qcadev;
+ unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200;
+ int ret;
+ int soc_ver;
+
+ qcadev = serdev_device_get_drvdata(hu->serdev);
+
+ switch (qcadev->btsoc_type) {
+ case BTQCA_CHEROKEE:
+ bt_dev_dbg(hdev, "setting up wcn3990");
+ /* Patch downloading has to be done without IBS mode */
+ clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
+ qca_set_init_speed(hu);
+ hci_uart_set_flow_control(hu, true);
+ ret = qca_send_vendor_cmd(hdev, CHEROKEE_POWERON_PULSE);
+ if (ret) {
+ bt_dev_err(hdev, "failed to send power on command");
+ return ret;
+ }
+
+ /* Close and re-open the port */
As mentioned earlier, this comment doesn't provide any useful
information, it's evident from the code. Rather explain *why* the
close/open is needed.
+ serdev_device_close(hu->serdev);
+ ret = serdev_device_open(hu->serdev);
+ if (ret) {
+ bt_dev_err(hdev, "failed to open port");
+ return ret;
+ }
+
+ qca_set_init_speed(hu);
+ hci_uart_set_flow_control(hu, false);
+ msleep(100);
Which step makes the delay necessary? I guess it's not enabling flow
control but probably sending the power on command. If that is correct
the delay should be done after the corresponding command.
+ ret = qca_patch_ver_req(hdev, &soc_ver);
+ if (ret < 0 || soc_ver == 0) {
+ bt_dev_err(hdev, "Failed to get version 0x%x", ret);
Probably better: "Failed to get version: %d" since ret contains an
errno and the problem wasn't that we couldn't get "version 0x<errno>".
+ return ret;
+ }
+
+ bt_dev_info(hdev, "wcn3990 controller version 0x%08x", soc_ver);
+ hci_uart_set_flow_control(hu, true);
Repeatedly switching on and off of flow control is a bit noisy, I
wonder if it could be hidden in a wrapper. From the code it seems that
flow control is disabled (true) for init speed and and enabled (false)
for operating speed. If this is correct the hci_uart_set_flow_control()
calls could be moved inside qca_set_oper/init_speed(). struct
qca_serdev
could have a flag indicating if flow control is supported at all to
skip the hci_uart_set_flow_control() calls for Rome.
Just an idea, no objections if you prefer to leave it as is and Marcel
is ok with it.
[Bala]: will update.
+ ret = qca_set_operating_speed(hu, &qca_baudrate);
+ if (ret)
+ return ret;
+ hci_uart_set_flow_control(hu, false);
+ /* Setup patch and NVM configurations */
+ ret = qca_uart_setup_cherokee(hdev, qca_baudrate, &soc_ver);
+
+ break;
+
+ default:
+ bt_dev_info(hdev, "ROME setup");
+
+ /* Patch downloading has to be done without IBS mode */
+ clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
+
+ /* Setup initial baudrate */
+ speed = 0;
+ if (hu->init_speed)
+ speed = hu->init_speed;
+ else if (hu->proto->init_speed)
+ speed = hu->proto->init_speed;
If you introduce helpers to determine the init/oper speed these should
also be used here. Probably best to do this in a separate patch.
[Bala]: will update ROME related stuff in other patch.
+
+ if (speed)
+ host_set_baudrate(hu, speed);
+
+ /* Setup user speed if needed */
+ speed = 0;
+ if (hu->oper_speed)
+ speed = hu->oper_speed;
+ else if (hu->proto->oper_speed)
+ speed = hu->proto->oper_speed;
ditto
[Bala]: will update.
+static void qca_disable_regulator(struct qca_vreg vregs,
+ struct regulator *regulator)
+{
+ /* Disable the regulator if requested by user
+ * or when fault to enable any regulator.
+ */
This comment is not useful. The following code simply disables the
regulator, why this is done is a question of the caller.
[Bala]: will update.
+ regulator_disable(regulator);
+ regulator_set_voltage(regulator, 0, vregs.max_uV);
+ if (vregs.load_uA)
+ regulator_set_load(regulator, 0);
+
+}
+
+int qca_btsoc_power_setup(struct hci_uart *hu, bool on)
+{
+ struct qca_vreg *vregs;
+ struct regulator_bulk_data *vreg_bulk;
+ struct qca_serdev *qcadev;
+ int i, num_vregs, ret = 0;
+
+ qcadev = serdev_device_get_drvdata(hu->serdev);
+ if (!qcadev || !qcadev->bt_power || !qcadev->bt_power->vreg_data ||
+ !qcadev->bt_power->vreg_bulk)
+ return -EINVAL;
+
+ vregs = qcadev->bt_power->vreg_data->vregs;
+ vreg_bulk = qcadev->bt_power->vreg_bulk;
+ num_vregs = qcadev->bt_power->vreg_data->num_vregs;
+ BT_DBG("on: %d", on);
+ if (on && !qcadev->bt_power->vregs_on) {
+ for (i = 0; i < num_vregs; i++) {
+ ret = qca_enable_regulator(vregs[i],
+ vreg_bulk[i].consumer);
+ if (ret)
+ break;
+ }
+ /* regulators failed */
Comment is not useful, BT_ERR below leaves things clear.
[Bala]: will update.
+ if (ret) {
+ BT_ERR("failed to enable regulator:%s", vregs[i].name);
+ /* turn off regulators which are enabled */
+ for (i = i - 1; i >= 0; i--)
+ qca_disable_regulator(vregs[i],
+ vreg_bulk[i].consumer);
+ } else {
+ qcadev->bt_power->vregs_on = true;
+ }
+ } else if (!on && qcadev->bt_power->vregs_on) {
+ /* turn off regulator in reverse order */
+ i = qcadev->bt_power->vreg_data->num_vregs - 1;
+ for ( ; i >= 0; i--)
+ qca_disable_regulator(vregs[i], vreg_bulk[i].consumer);
+ qcadev->bt_power->vregs_on = false;
+ }
+
+ return ret;
+}
+
+static int qca_init_regulators(struct qca_power *qca,
+ const struct qca_vreg *vregs, size_t num_vregs)
+{
+ int i;
+
+ qca->vreg_bulk = devm_kzalloc(qca->dev, num_vregs *
+ sizeof(struct regulator_bulk_data),
+ GFP_KERNEL);
+ if (!qca->vreg_bulk)
+ return -ENOMEM;
+
+ for (i = 0; i < num_vregs; i++)
+ qca->vreg_bulk[i].supply = vregs[i].name;
+
+ return devm_regulator_bulk_get(qca->dev, num_vregs, qca->vreg_bulk);
+}
+
static int qca_serdev_probe(struct serdev_device *serdev)
{
struct qca_serdev *qcadev;
+ const struct qca_vreg_data *data;
int err;
qcadev = devm_kzalloc(&serdev->dev, sizeof(*qcadev), GFP_KERNEL);
@@ -1014,34 +1301,72 @@ static int qca_serdev_probe(struct
serdev_device *serdev)
return -ENOMEM;
qcadev->serdev_hu.serdev = serdev;
+ data = of_device_get_match_data(&serdev->dev);
+ if (data && data->soc_type == BTQCA_CHEROKEE)
+ qcadev->btsoc_type = BTQCA_CHEROKEE;
+ else
+ qcadev->btsoc_type = BTQCA_ROME;
+
serdev_device_set_drvdata(serdev, qcadev);
+ if (qcadev->btsoc_type == BTQCA_CHEROKEE) {
+ qcadev->bt_power = devm_kzalloc(&serdev->dev,
+ sizeof(struct qca_power),
+ GFP_KERNEL);
+ if (!qcadev->bt_power)
+ return -ENOMEM;
+
+ qcadev->bt_power->dev = &serdev->dev;
+ qcadev->bt_power->vreg_data = data;
+ err = qca_init_regulators(qcadev->bt_power, data->vregs,
+ data->num_vregs);
+ if (err) {
+ BT_ERR("Failed to init regulators:%d", err);
+ devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk);
+ devm_kfree(&serdev->dev, qcadev->bt_power);
Not necessary, the memory is allocated with devm_kzalloc(&serdev->dev,
...), therefore it is freed if probe() fails.
[Bala]: will update.
+ goto out;
+ }
- qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable",
- GPIOD_OUT_LOW);
- if (IS_ERR(qcadev->bt_en)) {
- dev_err(&serdev->dev, "failed to acquire enable gpio\n");
- return PTR_ERR(qcadev->bt_en);
- }
+ qcadev->bt_power->vregs_on = false;
+ device_property_read_u32(&serdev->dev, "max-speed",
+ &qcadev->oper_speed);
+ if (!qcadev->oper_speed)
+ BT_INFO("UART will pick default operating speed");
+ err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto);
+ if (err) {
+ BT_ERR("wcn3990 serdev registration failed");
+ devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk);
+ devm_kfree(&serdev->dev, qcadev->bt_power);
no need to free memory.
[Bala]: will update.
+ goto out;
+ }
+ } else {
+ qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(qcadev->bt_en)) {
+ dev_err(&serdev->dev, "failed to acquire enable gpio\n");
+ return PTR_ERR(qcadev->bt_en);
+ }
- qcadev->susclk = devm_clk_get(&serdev->dev, NULL);
- if (IS_ERR(qcadev->susclk)) {
- dev_err(&serdev->dev, "failed to acquire clk\n");
- return PTR_ERR(qcadev->susclk);
- }
+ qcadev->susclk = devm_clk_get(&serdev->dev, NULL);
+ if (IS_ERR(qcadev->susclk)) {
+ dev_err(&serdev->dev, "failed to acquire clk\n");
+ return PTR_ERR(qcadev->susclk);
+ }
- err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ);
- if (err)
- return err;
+ err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ);
+ if (err)
+ return err;
- err = clk_prepare_enable(qcadev->susclk);
- if (err)
- return err;
+ err = clk_prepare_enable(qcadev->susclk);
+ if (err)
+ return err;
- err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto);
- if (err)
- clk_disable_unprepare(qcadev->susclk);
+ err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto);
+ if (err)
+ clk_disable_unprepare(qcadev->susclk);
+ }
+
+out: return err;
- return err;
}
static void qca_serdev_remove(struct serdev_device *serdev)
@@ -1050,11 +1375,17 @@ static void qca_serdev_remove(struct
serdev_device *serdev)
hci_uart_unregister_device(&qcadev->serdev_hu);
- clk_disable_unprepare(qcadev->susclk);
+ if (qcadev->btsoc_type == BTQCA_CHEROKEE) {
+ devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk);
+ devm_kfree(&serdev->dev, qcadev->bt_power);
no need to free memory
[Bala]: will update.
Thanks for reviewing will update the about comments in next patch set.
--
Regards
Balakrishna.
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
