[v6] * Addressed comments from Viresh about: ** Comments style ** Kconfig bool instead of tristate ** DT and documentation style ** Resourses deallocation on an error ** Typos [v5] * Rebased * Addressed comments from Bjorn about SPDX style, functions and parameters naming * Addressed comments from Viresh DT properties and style, comments style, resourses deallocation, documentation placement * Addressed comments from Sricharan about unnessesary include * Addressed comments from Nicolas * Addressed comments from Rob about the commit messages and acks * Addressed comments from Mark [v4] * Adressed all comments from Stephen * Added CPU regulator support * Added qcom-cpufreq-kryo driver [v3] * Rebased on top of the latest PLL driver changes * Addressed comment from Rob Herring for bindings [v2] * Addressed comments from Rob Herring for bindings * Addressed comments from Mark Rutland for memory barrier * Addressed comments from Julien Thierry for clock reenabling condition * Tuned the HW configuration for clock frequencies below 600MHz Clocks: This series adds support for the CPU clocks on msm8996 devices. The driver uses the existing PLL drivers and is required to control the CPU frequency scaling on the MSM8996. Regulators: Added SAW regulator support to the SPMI regulator driver. The SAW regulators will be controlled through special CPU registers instead of direct SPMI accesses. Cpufreq: The qcom-cpufreq-kryo driver is aimed to support different SOC versions. The driver reads eFuse information and chooses the required OPP subset by passing the OPP supported-hw parameter. A previous post of RFC can be found here: https://patchwork.kernel.org/patch/10377887/ Ilia Lin (11): soc: qcom: Separate kryo l2 accessors from PMU driver clk: qcom: Add CPU clock driver for msm8996 clk: qcom: Add DT bindings for CPU clock driver for msm8996 clk: qcom: Add ACD path to CPU clock driver for msm8996 dt: qcom: Add opp and thermal to the msm8996 regulator: qcom_spmi: Add support for SAW dt-bindings: qcom_spmi: Add support for SAW documentation dt: qcom: Add SAW regulator for 8x96 CPUs cpufreq: Add Kryo CPU scaling driver dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu dt: qcom: Add qcom-cpufreq-kryo driver configuration Rajendra Nayak (3): clk: qcom: Make clk_alpha_pll_configure available to modules clk: qcom: cpu-8996: Add support to switch to alternate PLL clk: qcom: cpu-8996: Add support to switch below 600Mhz .../devicetree/bindings/clock/qcom,kryocc.txt | 17 + .../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++ .../bindings/regulator/qcom,spmi-regulator.txt | 45 ++ arch/arm64/boot/dts/qcom/apq8096-db820c.dts | 2 +- arch/arm64/boot/dts/qcom/msm8996.dtsi | 650 +++++++++++++++++++- drivers/clk/clk-fixed-factor.c | 2 +- drivers/clk/qcom/Kconfig | 9 + drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/clk-alpha-pll.c | 1 + drivers/clk/qcom/clk-alpha-pll.h | 6 + drivers/clk/qcom/clk-cpu-8996.c | 519 ++++++++++++++++ drivers/cpufreq/Kconfig.arm | 11 + drivers/cpufreq/Makefile | 1 + drivers/cpufreq/cpufreq-dt-platdev.c | 3 + drivers/cpufreq/qcom-cpufreq-kryo.c | 148 +++++ drivers/perf/Kconfig | 1 + drivers/perf/qcom_l2_pmu.c | 90 +-- drivers/regulator/qcom_spmi-regulator.c | 133 +++- drivers/soc/qcom/Kconfig | 3 + drivers/soc/qcom/Makefile | 1 + drivers/soc/qcom/kryo-l2-accessors.c | 65 ++ include/soc/qcom/kryo-l2-accessors.h | 21 + 22 files changed, 2329 insertions(+), 80 deletions(-) create mode 100644 Documentation/devicetree/bindings/clock/qcom,kryocc.txt create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt create mode 100644 drivers/clk/qcom/clk-cpu-8996.c create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c create mode 100644 drivers/soc/qcom/kryo-l2-accessors.c create mode 100644 include/soc/qcom/kryo-l2-accessors.h -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
