Quoting Amit Nischal (2018-04-30 09:20:10)
> ---
> .../devicetree/bindings/clock/qcom,gcc.txt | 1 +
> drivers/clk/qcom/Kconfig | 10 +-
> drivers/clk/qcom/Makefile | 1 +
> drivers/clk/qcom/gcc-sdm845.c | 3480 ++++++++++++++++++++
> include/dt-bindings/clock/qcom,gcc-sdm845.h | 239 ++
Do the split that Rob suggests please, given that you're resending. And
also include his reviewed-by tag.
> 5 files changed, 3727 insertions(+), 4 deletions(-)
> create mode 100644 drivers/clk/qcom/gcc-sdm845.c
> create mode 100644 include/dt-bindings/clock/qcom,gcc-sdm845.h
>
> diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
> index e42e1af..3298beb 100644
> --- a/drivers/clk/qcom/Kconfig
> +++ b/drivers/clk/qcom/Kconfig
> @@ -218,13 +218,15 @@ config MSM_MMCC_8996
> Say Y if you want to support multimedia devices such as display,
> graphics, video encode/decode, camera, etc.
>
> -config MSM_GCC_8998
> - tristate "MSM8998 Global Clock Controller"
> +config SDM_GCC_845
> + tristate "SDM845 Global Clock Controller"
> + select QCOM_GDSC
> depends on COMMON_CLK_QCOM
> help
> - Support for the global clock controller on msm8998 devices.
> + Support for the global clock controller on Qualcomm Technologies, Inc
> + sdm845 devices.
> Say Y if you want to use peripheral devices such as UART, SPI,
> - i2c, USB, UFS, SD/eMMC, PCIe, etc.
> + I2C, USB, UFS, SDDC, PCIe, etc.
This is all wrong.
>
> config SPMI_PMIC_CLKDIV
> tristate "SPMI PMIC clkdiv Support"
> diff --git a/drivers/clk/qcom/gcc-sdm845.c b/drivers/clk/qcom/gcc-sdm845.c
> new file mode 100644
> index 0000000..6484cba
> --- /dev/null
> +++ b/drivers/clk/qcom/gcc-sdm845.c
> @@ -0,0 +1,3480 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + */
> +
[...]
> + .name = "gcc_disp_axi_clk",
> + .ops = &clk_branch2_ops,
> + },
> + },
> +};
> +
> +static struct clk_branch gcc_disp_gpll0_clk_src = {
> + .halt_reg = 0x52004,
> + .halt_check = BRANCH_HALT_DELAY,
What about this one? It's not a phy so I'm confused again why we're
unable to check the halt bit. To be clear(er), I don't see why we ever
want to have HALT_DELAY used. Hopefully we can remove that flag.
>From what I recall, the flag is there for clks that don't toggle their
status bit at all, but that we know take a few cycles to ungate the
upstream clk. So we threw a delay into the code to make sure that when
clk_enable() returned, a driver wouldn't try to use hardware before the
clk was actually on. But these cases should pretty much never happen,
hence all the pushback against this flag.
> + .clkr = {
> + .enable_reg = 0x52004,
> + .enable_mask = BIT(18),
> + .hw.init = &(struct clk_init_data){
> + .name = "gcc_disp_gpll0_clk_src",
> + .parent_names = (const char *[]){
> + "gpll0",
> + },
> + .num_parents = 1,
[...]
> + .enable_reg = 0x7508c,
> + .enable_mask = BIT(0),
> + .hw.init = &(struct clk_init_data){
> + .name = "gcc_ufs_card_phy_aux_clk",
> + .parent_names = (const char *[]){
> + "gcc_ufs_card_phy_aux_clk_src",
> + },
> + .num_parents = 1,
> + .flags = CLK_SET_RATE_PARENT,
> + .ops = &clk_branch2_ops,
> + },
> + },
> +};
> +
> +static struct clk_branch gcc_ufs_card_rx_symbol_0_clk = {
> + .halt_reg = 0x75018,
> + .halt_check = BRANCH_HALT_DELAY,
There are still HALT_DELAY flags for UFS though? Why?
Also, are you going to send DFS support for the QUP clks? I would like
to see that code merged soon.
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
