Document the bindings used for the sn65dsi86 DSI to eDP bridge. Changes in v1: - Rephrase the dt-binding descriptions to be more inline with existing bindings (Andrzej Hajda). - Add missing dt-binding that are parsed by corresponding driver (Andrzej Hajda). Changes in v2: - Remove edp panel specific dt-binding entries. Only keep bridge specific entries (Sean Paul). - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). Changes in v3: - Remove irq-gpio dt entry and instead populate is an interrupt property (Rob Herring). Changes in v4: - Add link to bridge chip datasheet (Stephen Boyd) - Add vpll and vcc regulator supply bindings (Stephen Boyd) - Add ref clk optional dt binding (Stephen Boyd) - Add gpio-controller optional dt binding (Stephen Boyd) Signed-off-by: Sandeep Panda <spanda@xxxxxxxxxxxxxx> Reviewed-by: Rob Herring <robh@xxxxxxxxxx> --- .../bindings/display/bridge/ti,sn65dsi86.txt | 76 ++++++++++++++++++++++ 1 file changed, 76 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt new file mode 100644 index 0000000..0d042ce --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt @@ -0,0 +1,76 @@ +SN65DSI86 DSI to eDP bridge chip +-------------------------------- + +This is the binding for Texas Instruments SN65DSI86 bridge. +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf + +Required properties: +- compatible: Must be "ti,sn65dsi86" +- reg: i2c address of the chip, 0x2d as per datasheet +- enable-gpios: OF device-tree gpio specification for bridge_en pin + +- vccio-supply: A 1.8V supply that powers up the digital IOs. +- vpll-supply: A 1.8V supply that powers up the displayport PLL. +- vcca-supply: A 1.2V supply that powers up the analog circuits. +- vcc-supply: A 1.2V supply that powers up the digital core. + +Optional properties: +- interrupts: Specifier for the SN65DSI86 interrupt line. +- hpd-gpios: OF device-tree gpio specifications for HPD pin. + +- refclk-freq-khz: Value specifying the frequency of reference clock in KHz unit. + +- gpio-controller: Marks the device has a GPIO controller. +- #gpio-cells: Number of GPIO cells. Refer to binding document "gpio/gpio.txt" +- #pwm-cells : Number of cells used to specify a PWM. See pwm.txt in this directory + for a description of the cell formats. + +Required nodes: + +This device has two video ports. Their connections are modelled using the +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for DSI input +- Video port 1 for eDP output + +Example +------- + +edp-bridge@2d { + compatible = "ti,sn65dsi86"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2d>; + + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio3>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + + vccio-supply = <&pm8916_l17>; + vcca-supply = <&pm8916_l6>; + vpll-supply = <&pm8916_l17>; + vcc-supply = <&pm8916_l6>; + + refclk-freq-khz = <19200>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + edp_bridge_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + edp_bridge_out: endpoint { + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +} -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html