Sven Eckelmann reported an issue with the current IPQ4019 pinctrl.
Setting up any gpio-hog in the device-tree for his device would
"kill the bootup completely":
| [ 0.477838] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 0.499828] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferring probe
| [ 1.298883] requesting hog GPIO enable USB2 power (chip 1000000.pinctrl, offset 58) failed, -517
| [ 1.299609] gpiochip_add_data: GPIOs 0..99 (1000000.pinctrl) failed to register
| [ 1.308589] ipq4019-pinctrl 1000000.pinctrl: Failed register gpiochip
| [ 1.316586] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 1.322415] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferri
This was also verified on a RT-AC58U (IPQ4018) which would
no longer boot, if a gpio-hog was specified. (Tried forcing
the USB LED PIN (GPIO0) to high.).
The problem is that Pinctrl+GPIO registration is currently
peformed in the following order in pinctrl-msm.c:
1. pinctrl_register()
2. gpiochip_add()
3. gpiochip_add_pin_range()
The actual error code -517 == -EPROBE_DEFER is coming from
pinctrl_get_device_gpio_range(), which is called through:
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_gpios
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
gpiochip_generic_request
pinctrl_gpio_request
pinctrl_get_device_gpio_range
pinctrl_get_device_gpio_range() is unable to find any valid
pin ranges, since nothing has been added to the pinctrldev_list yet.
so the range can't be found, and the operation fails with -EPROBE_DEFER.
This patch fixes the issue by adding the "gpio-ranges" property to
the pinctrl device node of all upstream Qcom SoC. The pin ranges are
then added by the gpio core.
In order to remain compatible with older, existing DTs (and ACPI)
a check for the "gpio-ranges" property has been added to
msm_gpio_init(). This prevents the driver of adding the same entry
to the pinctrldev_list twice.
Reported-by: Sven Eckelmann <sven.eckelmann@xxxxxxxxxxxx>
Signed-off-by: Christian Lamparter <chunkeey@xxxxxxxxx>
---
arch/arm/boot/dts/qcom-apq8064.dtsi | 1 +
arch/arm/boot/dts/qcom-apq8084.dtsi | 1 +
arch/arm/boot/dts/qcom-ipq4019.dtsi | 1 +
arch/arm/boot/dts/qcom-ipq8064.dtsi | 1 +
arch/arm/boot/dts/qcom-mdm9615.dtsi | 1 +
arch/arm/boot/dts/qcom-msm8660.dtsi | 1 +
arch/arm/boot/dts/qcom-msm8960.dtsi | 1 +
arch/arm/boot/dts/qcom-msm8974.dtsi | 1 +
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 3 ++-
arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 +
arch/arm64/boot/dts/qcom/msm8992.dtsi | 1 +
arch/arm64/boot/dts/qcom/msm8994.dtsi | 1 +
arch/arm64/boot/dts/qcom/msm8996.dtsi | 1 +
drivers/pinctrl/qcom/pinctrl-msm.c | 23 ++++++++++++++++++-----
14 files changed, 32 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 3ca96e361878..17ad9cbd9f8c 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -327,6 +327,7 @@
reg = <0x800000 0x4000>;
gpio-controller;
+ gpio-ranges = <&tlmm_pinmux 0 0 90>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index 0e1e98707e3f..d9481d083802 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -396,6 +396,7 @@
compatible = "qcom,apq8084-pinctrl";
reg = <0xfd510000 0x4000>;
gpio-controller;
+ gpio-ranges = <&tlmm 0 0 147>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index 10d112a4078e..9a81d2da87a0 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -146,6 +146,7 @@
compatible = "qcom,ipq4019-pinctrl";
reg = <0x01000000 0x300000>;
gpio-controller;
+ gpio-ranges = <&tlmm 0 0 100>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
index 1e0a3b446f7a..26eab9a68d90 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -108,6 +108,7 @@
reg = <0x800000 0x4000>;
gpio-controller;
+ gpio-ranges = <&qcom_pinmux 0 0 69>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom-mdm9615.dtsi
index c852b69229c9..cfdaca5f259a 100644
--- a/arch/arm/boot/dts/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom-mdm9615.dtsi
@@ -128,6 +128,7 @@
msmgpio: pinctrl@800000 {
compatible = "qcom,mdm9615-pinctrl";
gpio-controller;
+ gpio-ranges = <&msmgpio 0 0 88>;
#gpio-cells = <2>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index 33030f9419fe..47cf9c4ca062 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -110,6 +110,7 @@
reg = <0x800000 0x4000>;
gpio-controller;
+ gpio-ranges = <&tlmm 0 0 173>;
#gpio-cells = <2>;
interrupts = <0 16 0x4>;
interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index 1733d8f40ab1..f6d8b1af5a8a 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -102,6 +102,7 @@
msmgpio: pinctrl@800000 {
compatible = "qcom,msm8960-pinctrl";
gpio-controller;
+ gpio-ranges = <&msmgpio 0 0 152>;
#gpio-cells = <2>;
interrupts = <0 16 0x4>;
interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index d9019a49b292..1250e071a6e2 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -696,6 +696,7 @@
compatible = "qcom,msm8974-pinctrl";
reg = <0xfd510000 0x4000>;
gpio-controller;
+ gpio-ranges = <&msmgpio 0 0 146>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 2bc5dec5614d..d2c36b467466 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -24,11 +24,12 @@
ranges = <0 0 0 0xffffffff>;
compatible = "simple-bus";
- pinctrl@1000000 {
+ tlmm: pinctrl@1000000 {
compatible = "qcom,ipq8074-pinctrl";
reg = <0x1000000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
+ gpio-ranges = <&tlmm 0 0 70>;
#gpio-cells = <0x2>;
interrupt-controller;
#interrupt-cells = <0x2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index e51b04900726..e06cb90c8ec3 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -281,6 +281,7 @@
reg = <0x1000000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
+ gpio-ranges = <&msmgpio 0 0 122>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi
index 171578747ed0..173b6bc60816 100644
--- a/arch/arm64/boot/dts/qcom/msm8992.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi
@@ -179,6 +179,7 @@
reg = <0xfd510000 0x4000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
+ gpio-ranges = <&msmgpio 0 0 146>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index f33c41d01c86..68705db4696b 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -141,6 +141,7 @@
reg = <0xfd510000 0x4000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
+ gpio-ranges = <&msmgpio 0 0 146>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 0a6f7952bbb1..18511e782cbd 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -530,6 +530,7 @@
reg = <0x01010000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
+ gpio-ranges = <&msmgpio 0 0 150>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index e7abc8ba222b..ed889553f01c 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -890,11 +890,24 @@ static int msm_gpio_init(struct msm_pinctrl *pctrl)
return ret;
}
- ret = gpiochip_add_pin_range(&pctrl->chip, dev_name(pctrl->dev), 0, 0, chip->ngpio);
- if (ret) {
- dev_err(pctrl->dev, "Failed to add pin range\n");
- gpiochip_remove(&pctrl->chip);
- return ret;
+ /*
+ * For DeviceTree-supported systems, the gpio core checks the
+ * pinctrl's device node for the "gpio-ranges" property.
+ * If it is present, it takes care of adding the pin ranges
+ * for the driver. In this case the driver can skip ahead.
+ *
+ * In order to remain compatible with older, existing DeviceTree
+ * files which don't set the "gpio-ranges" property or systems that
+ * utilize ACPI the driver has to call gpiochip_add_pin_range().
+ */
+ if (!of_property_read_bool(pctrl->dev->of_node, "gpio-ranges")) {
+ ret = gpiochip_add_pin_range(&pctrl->chip,
+ dev_name(pctrl->dev), 0, 0, chip->ngpio);
+ if (ret) {
+ dev_err(pctrl->dev, "Failed to add pin range\n");
+ gpiochip_remove(&pctrl->chip);
+ return ret;
+ }
}
ret = gpiochip_irqchip_add(chip,
--
2.17.0
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
