On Thu 05 Apr 09:18 PDT 2018, Lina Iyer wrote:
> diff --git a/drivers/soc/qcom/rpmh-internal.h b/drivers/soc/qcom/rpmh-internal.h
[..]
> @@ -439,6 +445,107 @@ int rpmh_rsc_send_data(struct rsc_drv *drv, const struct tcs_request *msg)
> }
> EXPORT_SYMBOL(rpmh_rsc_send_data);
>
> +static int find_match(const struct tcs_group *tcs, const struct tcs_cmd *cmd,
> + int len)
> +{
> + int i, j;
> +
> + /* Check for already cached commands */
> + for_each_set_bit(i, tcs->slots, MAX_TCS_SLOTS) {
Wouldn't it be good if this cared about TCS boundaries?
> + for (j = 0; j < len; j++) {
> + if (tcs->cmd_cache[i] != cmd[0].addr) {
> + if (j == 0)
> + break;
> + WARN(tcs->cmd_cache[i + j] != cmd[j].addr,
> + "Message does not match previous sequence.\n");
> + return -EINVAL;
> + } else if (j == len - 1) {
> + return i;
> + }
> + }
> + }
> +
> + return -ENODATA;
> +}
> +
> +static int find_slots(struct tcs_group *tcs, const struct tcs_request *msg,
> + int *m, int *n)
> +{
> + int slot, offset;
> + int i = 0;
> +
> + /* Find if we already have the msg in our TCS */
"Search for the sequence of addresses in our tcs group"
> + slot = find_match(tcs, msg->cmds, msg->num_cmds);
> + if (slot >= 0)
> + goto copy_data;
> +
> + /* Do over, until we can fit the full payload in a TCS */
> + do {
> + slot = bitmap_find_next_zero_area(tcs->slots, MAX_TCS_SLOTS,
> + i, msg->num_cmds, 0);
> + if (slot == MAX_TCS_SLOTS)
> + return -ENOMEM;
> + i += tcs->ncpt;
> + } while (slot + msg->num_cmds - 1 >= i);
Does this conditional check that the sequence of free slots that we
found doesn't extend past the boundary of a TCS?
I'm sorry, but this code is hard to understand. I would find this much
easier to read if there was one bitmap per TCS and you just looped over
them to find free regions.
> +
> +copy_data:
> + bitmap_set(tcs->slots, slot, msg->num_cmds);
> + /* Copy the addresses of the resources over to the slots */
> + for (i = 0; i < msg->num_cmds; i++)
> + tcs->cmd_cache[slot + i] = msg->cmds[i].addr;
> +
> + offset = slot / tcs->ncpt;
> + *m = offset + tcs->offset;
> + *n = slot % tcs->ncpt;
> +
> + return 0;
> +}
> +
> +static int tcs_ctrl_write(struct rsc_drv *drv, const struct tcs_request *msg)
> +{
> + struct tcs_group *tcs;
> + int m = 0, n = 0;
> + unsigned long flags;
> + int ret;
> +
> + tcs = get_tcs_for_msg(drv, msg);
> + if (IS_ERR(tcs))
> + return PTR_ERR(tcs);
> +
> + spin_lock_irqsave(&tcs->lock, flags);
> + /* find the m-th TCS and the n-th position in the TCS to write to */
> + ret = find_slots(tcs, msg, &m, &n);
> + if (!ret)
> + __tcs_buffer_write(drv, m, n, msg);
> + spin_unlock_irqrestore(&tcs->lock, flags);
> +
> + return ret;
> +}
> +
> +/**
> + * rpmh_rsc_write_ctrl_data: Write request to the controller
> + *
> + * @drv: the controller
> + * @msg: the data to be written to the controller
> + *
> + * There is no response returned for writing the request to the controller.
> + */
> +int rpmh_rsc_write_ctrl_data(struct rsc_drv *drv, const struct tcs_request *msg)
So this is exactly the same thing as rpmh_rsc_send_data() but for one of
the non-active TCSs?
Can't we have a single API for writing msg to the hardware and if it's
active we "send" it as well?
> +{
> + if (!msg || !msg->cmds || !msg->num_cmds ||
> + msg->num_cmds > MAX_RPMH_PAYLOAD) {
> + pr_err("Payload error\n");
> + return -EINVAL;
> + }
> +
> + /* Data sent to this API will not be sent immediately */
> + if (msg->state == RPMH_ACTIVE_ONLY_STATE)
> + return -EINVAL;
If you're concerned about this then the API isn't clear enough.
> +
> + return tcs_ctrl_write(drv, msg);
> +}
> +EXPORT_SYMBOL(rpmh_rsc_write_ctrl_data);
> +
> static int rpmh_probe_tcs_config(struct platform_device *pdev,
> struct rsc_drv *drv)
> {
> @@ -512,6 +619,19 @@ static int rpmh_probe_tcs_config(struct platform_device *pdev,
> tcs->mask = ((1 << tcs->num_tcs) - 1) << st;
> tcs->offset = st;
> st += tcs->num_tcs;
> +
> + /*
> + * Allocate memory to cache sleep and wake requests to
> + * avoid reading TCS register memory.
> + */
> + if (tcs->type == ACTIVE_TCS)
> + continue;
Rather than "the rest of this loop shouldn't be done for the active tcs
group" just make another loop... Or at least make the comment relate
directly to the code it's adjacent.
> +
> + tcs->cmd_cache = devm_kcalloc(&pdev->dev,
> + tcs->num_tcs * ncpt, sizeof(u32),
> + GFP_KERNEL);
> + if (!tcs->cmd_cache)
> + return -ENOMEM;
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
