On Wed 28 Mar 11:07 PDT 2018, Christian Lamparter wrote:
> Sven Eckelmann reported an issue with the current IPQ4019 pinctrl.
> Setting up any gpio-hog in the device-tree for his device would
> "kill the bootup completely":
>
> | [ 0.477838] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
> | [ 0.499828] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferring probe
> | [ 1.298883] requesting hog GPIO enable USB2 power (chip 1000000.pinctrl, offset 58) failed, -517
> | [ 1.299609] gpiochip_add_data: GPIOs 0..99 (1000000.pinctrl) failed to register
> | [ 1.308589] ipq4019-pinctrl 1000000.pinctrl: Failed register gpiochip
> | [ 1.316586] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
> | [ 1.322415] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferri
>
> This was also verified on a RT-AC58U (IPQ4018) which would
> no longer boot, if a gpio-hog was specified. (Tried forcing
> the USB LED PIN (GPIO0) to high.).
>
It's quite clear that this is a generic issue with the msm pinctrl
driver.
For the cases where I've been in need of static configuration of
certain pins I've simply made the pinctrl node itself have a pinctrl-0
that refer to a state that I want to hold. This has worked well and I
didn't even know about the gpio-hog property.
[..]
> diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
> index 3ca96e361878..17ad9cbd9f8c 100644
> --- a/arch/arm/boot/dts/qcom-apq8064.dtsi
> +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
> @@ -327,6 +327,7 @@
> reg = <0x800000 0x4000>;
>
> gpio-controller;
> + gpio-ranges = <&tlmm_pinmux 0 0 90>;
This seems reasonable.
> #gpio-cells = <2>;
> interrupt-controller;
> #interrupt-cells = <2>;
[..]
> diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
> index 495432f3341b..f2580bbba741 100644
> --- a/drivers/pinctrl/qcom/pinctrl-msm.c
> +++ b/drivers/pinctrl/qcom/pinctrl-msm.c
> @@ -831,13 +831,6 @@ static int msm_gpio_init(struct msm_pinctrl *pctrl)
> return ret;
> }
>
> - ret = gpiochip_add_pin_range(&pctrl->chip, dev_name(pctrl->dev), 0, 0, chip->ngpio);
> - if (ret) {
> - dev_err(pctrl->dev, "Failed to add pin range\n");
> - gpiochip_remove(&pctrl->chip);
> - return ret;
> - }
> -
But, this will break backwards compatibility with existing DTBs and I
don't see how this would work with the ACPI based platforms using this
driver.
Iirc this driver follows the same pattern as several other pinctrl
drivers providing gpios, how are they handling this?
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
