Hi,
On 3/19/2018 5:56 PM, Doug Anderson wrote:
> Hi,
>
> On Mon, Mar 19, 2018 at 3:15 PM, Sagar Dharia <sdharia@xxxxxxxxxxxxxx> wrote:
>>>> + pinconf {
>>>> + pins = "gpio55", "gpio56";
>>>> + drive-strength = <2>;
>>>> + bias-disable;
>>>> + };
>>>> + };
>>>> +
>>>> + qup-i2c10-sleep {
>>>> + pinconf {
>>>> + pins = "gpio55", "gpio56";
>>>> + bias-pull-up;
>>>
>>> Are you sure that you want pullups enabled for sleep here? There are
>>> external pulls on this line (as there are on many i2c busses) so doing
>>> this will double-enable pulls. It probably won't hurt, but I'm
>>> curious if there's some sort of reason here.
>>>
>> 1. We need the lines to remain high to avoid slaves sensing a false
>> start-condition (this can happen if the SDA goes down before SCL).
>> 2. Disclaimer: I'm not a HW expert, but we were told that
>> tri-state/bias-disabled lines can draw more current. I will find out
>> more about that.
>
> Agreed that they need to remain high, but you've got very strong
> pullups external to the SoC. Those will keep it high. You don't need
> the internal ones too.
>
> As extra evidence that the external pullups _must_ be present on your
> board: you specify bias-disable in the active state. That can only
> work if there are external pullups (or if there were some special
> extra secret internal pullups that were part of geni). i2c is an
> open-drain bus and thus there must be pullups on the bus in order to
> communicate.
>
You are right, I followed up about the pull-up recommendation and that
was for a GPIO where there was no external pull-up (GPIO was not used
for I2C). It's safe to assume I2C will always have external pullup. We
will change sleep-config of I2C GPIOs to no-pull.
>
>>>> + };
>>>> + };
>>>> };
>>>> };
>>>> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
>>>> index 59334d9..9ef056f 100644
>>>> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
>>>> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
>>>> @@ -209,6 +209,21 @@
>>>> pins = "gpio4", "gpio5";
>>>> };
>>>> };
>>>> +
>>>> + qup_i2c10_default: qup-i2c10-default {
>>>> + pinmux {
>>>> + function = "qup10";
>>>> + pins = "gpio55", "gpio56";
>>>> + };
>>>> + };
>>>> +
>>>> + qup_i2c10_sleep: qup-i2c10-sleep {
>>>> + pinmux {
>>>> + function = "gpio";
>>>> + pins = "gpio55", "gpio56";
>>>> + };
>>>> + };
>>>> +
>>>> };
>>>>
>>>> timer@17c90000 {
>>>> @@ -309,6 +324,20 @@
>>>> interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
>>>> status = "disabled";
>>>> };
>>>> +
>>>> + i2c10: i2c@a88000 {
>>>
>>> Seems like it might be nice to add all the i2c busses into the main
>>> sdm845.dtsi file. Sure, most won't be enabled, but it seems like it
>>> would avoid churn later.
>>>
>>> ...if you're sure you want to add only one i2c controller, subject of
>>> this patch should indicate that.
>>>
>>
>> Yes, we typically have a "platform(sdm845 here)-qupv3.dtsi" defining
>> most of the serial-bus instances (i2c, spi, and uart with
>> status=disabled) that we include from the common header. The boards
>> enable instances they need.
>> Will that be okay?
>
> Unless you really feel the need to put these in a separate file I'd
> just put them straight in sdm845.dtsi. Yeah, it'll get big, but
> that's OK by me. I _think_ this matches what Bjorn was suggesting on
> previous device tree patches, but CCing him just in case. I'm
> personally OK with whatever Bjorn and other folks with more Qualcomm
> history would like.
>
> ...but yeah, I'm asking for them all to be listed with status="disabled".
>
Sure, we will change the subject of this patch to indicate that we are
adding 1 controller as of now. Later we will add all I2C controllers to
dtsi as another patch since that will need pinctrl settings for GPIOs
used by those instances and the wrappers devices needed by them.
Thanks
Sagar
>
> -Doug
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
