Quoting ilialin@xxxxxxxxxxxxxx (2018-03-20 06:53:08)
>
>
> > -----Original Message-----
> > From: Stephen Boyd <sboyd@xxxxxxxxxx>
> > Sent: Monday, March 19, 2018 18:50
> > To: Ilia Lin <ilialin@xxxxxxxxxxxxxx>; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx;
> > linux-arm-msm@xxxxxxxxxxxxxxx; linux-clk@xxxxxxxxxxxxxxx;
> > sboyd@xxxxxxxxxxxxxx
> > Cc: mark.rutland@xxxxxxx; devicetree@xxxxxxxxxxxxxxx;
> > rnayak@xxxxxxxxxxxxxx; robh@xxxxxxxxxx; will.deacon@xxxxxxx;
> > amit.kucheria@xxxxxxxxxx; tfinkel@xxxxxxxxxxxxxx; ilialin@xxxxxxxxxxxxxx;
> > nicolas.dechesne@xxxxxxxxxx; celster@xxxxxxxxxxxxxx
> > Subject: Re: [PATCH v3 07/10] clk: qcom: clk-cpu-8996: Prepare PLLs on probe
> >
> > Quoting Ilia Lin (2018-02-14 05:59:49)
> > > The PLLs must be prepared enabled during the probe to be accessible by
> > > the OPPs. Otherwise an OPP may switch to non-enabled clock.
> >
> > Sounds like an OPP problem.
>
> And again, it could be solved by a platform specific cpufreq driver. Worth it?
>
> >
> > > #include "clk-alpha-pll.h"
> > >
> > > #define VCO(a, b, c) { \
> > > @@ -376,6 +376,18 @@ struct clk_hw_clks {
> > > clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
> > > clk_alpha_pll_configure(&pwrcl_alt_pll, regmap,
> > > &altpll_config);
> > >
> > > + /* Enable all PLLs and alt PLLs */
> > > + clk_prepare_enable(pwrcl_alt_pll.clkr.hw.clk);
> > > + clk_prepare_enable(perfcl_alt_pll.clkr.hw.clk);
> > > + clk_prepare_enable(pwrcl_pll.clkr.hw.clk);
> > > + clk_prepare_enable(perfcl_pll.clkr.hw.clk);
> >
> > And this can't be done by the cpufreq-dt driver?
>
> Are you suggesting changing the cpufreq-dt as well?
Yes?
>
> >
> > > +
> > > + /* Set initial boot frequencies for power/perf PLLs */
> > > + clk_set_rate(pwrcl_alt_pll.clkr.hw.clk, 652800000);
> > > + clk_set_rate(perfcl_alt_pll.clkr.hw.clk, 652800000);
> > > + clk_set_rate(pwrcl_pll.clkr.hw.clk, 652800000);
> > > + clk_set_rate(perfcl_pll.clkr.hw.clk, 652800000);
> >
> > We have assigned rates in DT for this.
>
> I assumed that the clock driver can live without the OPP table and any cpufreq driver. Or do you mean adding this as parameters for the kryocc DT node?
>
Yes I mean adding assigned rates to the kroycc DT node to setup PLLs to
rates you want.
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
