Hi,
On 3/14/2018 10:13 PM, Dmitry Torokhov wrote:
On Tue, Mar 13, 2018 at 07:40:48PM -0700, Bjorn Andersson wrote:
On Tue 13 Mar 01:35 PDT 2018, Tirupathi Reddy wrote:
Add resin key support to handle different types of key events
defined in different platforms.
Signed-off-by: Tirupathi Reddy <tirupath@xxxxxxxxxxxxxx>
---
.../bindings/input/qcom,pm8941-pwrkey.txt | 20 ++++++-
drivers/input/misc/pm8941-pwrkey.c | 65 +++++++++++++++++++++-
2 files changed, 83 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt
index 07bf55f..f499cf8 100644
--- a/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt
+++ b/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt
@@ -20,6 +20,14 @@ PROPERTIES
defined by the binding document describing the node's
interrupt parent.
+- interrupt-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Interrupt names. This list must match up 1-to-1 with the
+ interrupts specified in the 'interrupts' property. "kpdpwr"
+ must be specified and should be the first entry of the list.
+ "resin" may be specified for some platforms.
+
- debounce:
Usage: optional
Value type: <u32>
@@ -32,12 +40,22 @@ PROPERTIES
Definition: presence of this property indicates that the KPDPWR_N pin
should be configured for pull up.
+- linux,code:
+ Usage: required for "resin" key
+ Value type: <u32>
+ Definition: The input key-code associated with the resin key.
+ Use the linux event codes defined in
+ include/dt-bindings/input/linux-event-codes.h
For completeness sake I think this should list both the key code for the
power key and for the RESIN key.
Then it breaks existing DT nodes.
Since pwrkey functionality is fixed across platforms, "linux,code"
specification through device tree is not required for it.
+
EXAMPLE
pwrkey@800 {
compatible = "qcom,pm8941-pwrkey";
reg = <0x800>;
- interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ interrupt-names = "kpdpwr", "resin";
debounce = <15625>;
bias-pull-up;
Do we need to support defining the bias for the resin as well?
Good point, will add this support in Patch V3. Also, the debounce
configuration
in HW is common across power-key and resin.
Perhaps it makes more sense to describe the RESIN key with a separate
compatible and define that in a node of its own (we can still implement
this in the same driver - if there's any chance of reuse...).
The PMIC peripheral/module called PON(Power on) generates these key events.
Pwrkey(KPDPWR_N) is the primary supported key by this module, the others are
optional. The resin may be supported a "defined" key. How about using
the below
logic for resin key without breaking the existing DTs as shown below:
pwrkey@800 {
compatible = "qcom,pm8941-pwrkey";
reg = <0x800>;
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
resin {
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
linux,code = <KEY_VOLUMEDOWN>;
bias-pull-up;
};
};
+ linux,code = <KEY_VOLUMEDOWN>;
};
diff --git a/drivers/input/misc/pm8941-pwrkey.c b/drivers/input/misc/pm8941-pwrkey.c
index 18ad956..2fffc7c 100644
--- a/drivers/input/misc/pm8941-pwrkey.c
+++ b/drivers/input/misc/pm8941-pwrkey.c
@@ -28,6 +28,7 @@
#define PON_RT_STS 0x10
#define PON_KPDPWR_N_SET BIT(0)
+#define PON_RESIN_N_SET BIT(1)
#define PON_PS_HOLD_RST_CTL 0x5a
#define PON_PS_HOLD_RST_CTL2 0x5b
@@ -46,6 +47,7 @@
struct pm8941_pwrkey {
struct device *dev;
int irq;
+ u32 resin_key_code;
u32 baseaddr;
struct regmap *regmap;
struct input_dev *input;
@@ -130,6 +132,24 @@ static irqreturn_t pm8941_pwrkey_irq(int irq, void *_data)
return IRQ_HANDLED;
}
+static irqreturn_t pm8941_resinkey_irq(int irq, void *_data)
+{
+ struct pm8941_pwrkey *pwrkey = _data;
+ unsigned int sts;
+ int error;
+
+ error = regmap_read(pwrkey->regmap,
+ pwrkey->baseaddr + PON_RT_STS, &sts);
This needs to be broken because the line is 81 chars long, if you use a
shorter name for the return value (e.g. "ret") you don't need to do
this.
I prefer keeping it as "error" please.
Okay. I will keep it as "error".
+ if (error)
+ return IRQ_HANDLED;
+
+ input_report_key(pwrkey->input, pwrkey->resin_key_code,
+ !!(sts & PON_RESIN_N_SET));
Put pwrkey->resin_key_code in a local variable named "key" (or even
key_code) and you don't need to line wrap this one.
Okay. I will address it in Patch V3.
+ input_sync(pwrkey->input);
+
+ return IRQ_HANDLED;
+}
+
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
