On 2018-02-16 10:05, Sricharan R wrote:
On 2/3/2018 1:28 PM, Abhishek Sahu wrote:
Currently each message length in complete transfer is being
checked for determining DMA mode and if any of the message length
is less than FIFO length then non DMA mode is being used which
will increase overhead. DMA can be used for any length and it
should be determined with complete transfer length. Now, this
patch introduces DMA threshold length and the transfer will be
done in DMA mode if the total length is greater than this
threshold length.
Signed-off-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
---
drivers/i2c/busses/i2c-qup.c | 15 +++++++++------
1 file changed, 9 insertions(+), 6 deletions(-)
diff --git a/drivers/i2c/busses/i2c-qup.c
b/drivers/i2c/busses/i2c-qup.c
index 6227a5c..a91fc70 100644
--- a/drivers/i2c/busses/i2c-qup.c
+++ b/drivers/i2c/busses/i2c-qup.c
@@ -192,6 +192,8 @@ struct qup_i2c_dev {
bool is_dma;
/* To check if the current transfer is using DMA */
bool use_dma;
+ /* The threshold length above which DMA will be used */
+ unsigned int dma_threshold;
struct dma_pool *dpool;
struct qup_i2c_tag start_tag;
struct qup_i2c_bam brx;
@@ -1294,7 +1296,8 @@ static int qup_i2c_xfer_v2(struct i2c_adapter
*adap,
int num)
{
struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
- int ret, len, idx = 0;
+ int ret, idx = 0;
+ unsigned int total_len = 0;
qup->bus_err = 0;
qup->qup_err = 0;
@@ -1320,14 +1323,13 @@ static int qup_i2c_xfer_v2(struct i2c_adapter
*adap,
goto out;
}
- len = (msgs[idx].len > qup->out_fifo_sz) ||
- (msgs[idx].len > qup->in_fifo_sz);
-
- if (is_vmalloc_addr(msgs[idx].buf) || !len)
+ if (is_vmalloc_addr(msgs[idx].buf))
break;
+
+ total_len += msgs[idx].len;
}
- if (idx == num)
+ if (idx == num && total_len > qup->dma_threshold)
qup->use_dma = true;
}
@@ -1587,6 +1589,7 @@ static int qup_i2c_probe(struct platform_device
*pdev)
size = QUP_INPUT_FIFO_SIZE(io_mode);
qup->in_fifo_sz = qup->in_blk_sz * (2 << size);
+ qup->dma_threshold = min(qup->out_fifo_sz, qup->in_fifo_sz);
The patch is fine. small nit, you can avoid this global
dma_threshold. Instead
have it locally in qup_i2c_xfer_v2 itself.
Thanks Sricharan.
The idea for introducing global dma_threshold was to give option
for controlling the behavior from one place. If someone wants to
change the length above which dma will be used, then It can be
controlled from once place in the probe function itself.
Also, min(qup->out_fifo_sz, qup->in_fifo_sz) requires comparison
and adding in qup_i2c_xfer_v2 will make this happen everytime.
Regards,
Abhishek
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
