On Tue, Jan 16, 2018 at 07:02:34PM +0000, srinivas.kandagatla@xxxxxxxxxx wrote: > From: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx> > > When Linux is master of BAM, it can directly read registers to know number > of supported channels, however when its remotely controlled reading these > registers would trigger a crash if the BAM is not yet intialized/powered up > on the remote side. > > This patch adds num-channels binding to specify number of supported > dma channels on remotely controlled BAM. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx> > --- > Documentation/devicetree/bindings/dma/qcom_bam_dma.txt | 2 ++ > drivers/dma/qcom/bam_dma.c | 13 +++++++++++-- > 2 files changed, 13 insertions(+), 2 deletions(-) > > diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt > index 9cbf5d9df8fd..aa6822cbb230 100644 > --- a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt > +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt > @@ -15,6 +15,8 @@ Required properties: > the secure world. > - qcom,controlled-remotely : optional, indicates that the bam is controlled by > remote proccessor i.e. execution environment. > +- num-channels : optional, indicates supported number of DMA channels in a > + remotely controlled bam. > > Example: > > diff --git a/drivers/dma/qcom/bam_dma.c b/drivers/dma/qcom/bam_dma.c > index 78e488e8f96d..523bd178047a 100644 > --- a/drivers/dma/qcom/bam_dma.c > +++ b/drivers/dma/qcom/bam_dma.c > @@ -1083,8 +1083,10 @@ static int bam_init(struct bam_device *bdev) > if (bdev->ee >= val) > return -EINVAL; > > - val = readl_relaxed(bam_addr(bdev, 0, BAM_NUM_PIPES)); > - bdev->num_channels = val & BAM_NUM_PIPES_MASK; > + if (!bdev->num_channels) { > + val = readl_relaxed(bam_addr(bdev, 0, BAM_NUM_PIPES)); > + bdev->num_channels = val & BAM_NUM_PIPES_MASK; > + } > > if (bdev->controlled_remotely) > return 0; > @@ -1179,6 +1181,13 @@ static int bam_dma_probe(struct platform_device *pdev) > bdev->controlled_remotely = of_property_read_bool(pdev->dev.of_node, > "qcom,controlled-remotely"); > > + if (bdev->controlled_remotely) { hmm so if we remove the remotely controlled instanced from DT and then Linux won't see them and not do anything. Do we need to do configuration of these instances too? > + ret = of_property_read_u32(pdev->dev.of_node, "num-channels", > + &bdev->num_channels); > + if (ret) > + dev_err(bdev->dev, "num-channels unspecified in dt\n"); > + } > + > bdev->bamclk = devm_clk_get(bdev->dev, "bam_clk"); > if (IS_ERR(bdev->bamclk)) { > bdev->bamclk = NULL; > -- > 2.15.1 > -- ~Vinod -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html