Manu,
On 16/01/18 08:26, Manu Gautam wrote:
> Commit 689bf72c6e0d ("usb: dwc3: Don't reinitialize core during
> host bus-suspend/resume") updated suspend/resume routines to not
> power_off and reinit PHYs/core for host mode.
> It broke platforms that rely on DWC3 core to power_off PHYs to
> enter low power state on system suspend.
>
> Perform dwc3_core_exit/init only during host mode system_suspend/
> resume to addresses power regression from above mentioned patch
> and also allow USB session to stay connected across
> runtime_suspend/resume in host mode.
>
> Fixes: 689bf72c6e0d ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume")
> Signed-off-by: Manu Gautam <mgautam@xxxxxxxxxxxxxx>
> ---
> drivers/usb/dwc3/core.c | 23 +++++++++++++++--------
> 1 file changed, 15 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index 0783250..e9fbee9 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -1279,7 +1279,7 @@ static int dwc3_remove(struct platform_device *pdev)
> }
>
> #ifdef CONFIG_PM
> -static int dwc3_suspend_common(struct dwc3 *dwc)
> +static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
> {
> unsigned long flags;
>
> @@ -1292,14 +1292,16 @@ static int dwc3_suspend_common(struct dwc3 *dwc)
> break;
> case DWC3_GCTL_PRTCAP_HOST:
> default:
> - /* do nothing */
> + /* do nothing during host runtime_suspend */
> + if (!PMSG_IS_AUTO(msg))
> + dwc3_core_exit(dwc);
> break;
since we're now doing something specific to HOST case we need to separate out the 'default' case
so,
+ default:
+ break;
> }
>
> return 0;
> }
>
> -static int dwc3_resume_common(struct dwc3 *dwc)
> +static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg)
> {
> unsigned long flags;
> int ret;
> @@ -1316,7 +1318,12 @@ static int dwc3_resume_common(struct dwc3 *dwc)
> break;
> case DWC3_GCTL_PRTCAP_HOST:
> default:
> - /* do nothing */
> + /* nothing to do on host runtime_resume */
> + if (!PMSG_IS_AUTO(msg)) {
> + ret = dwc3_core_init(dwc);
> + if (ret)
> + return ret;
> + }
> break;
same here.
> }
>
> @@ -1348,7 +1355,7 @@ static int dwc3_runtime_suspend(struct device *dev)
> if (dwc3_runtime_checks(dwc))
> return -EBUSY;
>
> - ret = dwc3_suspend_common(dwc);
> + ret = dwc3_suspend_common(dwc, PMSG_AUTO_SUSPEND);
> if (ret)
> return ret;
>
> @@ -1364,7 +1371,7 @@ static int dwc3_runtime_resume(struct device *dev)
>
> device_init_wakeup(dev, false);
>
> - ret = dwc3_resume_common(dwc);
> + ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME);
> if (ret)
> return ret;
>
> @@ -1411,7 +1418,7 @@ static int dwc3_suspend(struct device *dev)
> struct dwc3 *dwc = dev_get_drvdata(dev);
> int ret;
>
> - ret = dwc3_suspend_common(dwc);
> + ret = dwc3_suspend_common(dwc, PMSG_SUSPEND);
> if (ret)
> return ret;
>
> @@ -1427,7 +1434,7 @@ static int dwc3_resume(struct device *dev)
>
> pinctrl_pm_select_default_state(dev);
>
> - ret = dwc3_resume_common(dwc);
> + ret = dwc3_resume_common(dwc, PMSG_RESUME);
> if (ret)
> return ret;
>
>
You also need to fix-up
index e9fbee9..a213295 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -1333,12 +1333,11 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg)
static int dwc3_runtime_checks(struct dwc3 *dwc)
{
switch (dwc->current_dr_role) {
- case USB_DR_MODE_PERIPHERAL:
- case USB_DR_MODE_OTG:
+ case DWC3_GCTL_PRTCAP_DEVICE:
if (dwc->connected)
return -EBUSY;
break;
- case USB_DR_MODE_HOST:
+ case DWC3_GCTL_PRTCAP_HOST:
default:
/* do nothing */
break;
and finally
index a213295..728955c 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -218,7 +218,7 @@ static int dwc3_core_soft_reset(struct dwc3 *dwc)
* XHCI driver will reset the host block. If dwc3 was configured for
* host-only mode, then we can return early.
*/
- if (dwc->dr_mode == USB_DR_MODE_HOST)
+ if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST)
return 0;
reg = dwc3_readl(dwc->regs, DWC3_DCTL);
After these changes applied, I could get suspend/resume working properly on dra7x-evm
for host, device and dual-role cases.
--
cheers,
-roger
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
