Re: [PATCH v2 2/7] dt-bindings: soc: qcom: Add device tree binding for GENI SE

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri 12 Jan 17:05 PST 2018, Karthikeyan Ramasubramanian wrote:

> Add device tree binding support for the QCOM GENI SE driver.
> 
> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>

Better describe the entire GENI, with it's functions in the same
binding.

> ---
>  .../devicetree/bindings/soc/qcom/qcom,geni-se.txt  | 34 ++++++++++++++++++++++
>  1 file changed, 34 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> 
> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> new file mode 100644
> index 0000000..66f8a16
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> @@ -0,0 +1,34 @@
> +Qualcomm Technologies, Inc. GENI Serial Engine QUP Wrapper Controller
> +
> +Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper
> +is a programmable module for supporting a wide range of serial interfaces
> +like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial
> +Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP
> +Wrapper controller is modeled as a node with zero or more child nodes each
> +representing a serial engine.
> +
> +Required properties:
> +- compatible:		Must be "qcom,geni-se-qup".
> +- reg:			Must contain QUP register address and length.
> +- clock-names:		Must contain "m-ahb" and "s-ahb".
> +- clocks:		AHB clocks needed by the device.
> +
> +Required properties if child node exists:
> +- #address-cells: Must be 1
> +- #size-cells: Must be 1

But on a 64-bit system, shouldn't these be 2?

> +- ranges: Must be present
> +
> +Properties for children:
> +
> +A GENI based QUP wrapper controller node can contain 0 or more child nodes
> +representing serial devices.  These serial devices can be a QCOM UART, I2C
> +controller, spi controller, or some combination of aforementioned devices.
> +
> +Example:
> +	qup0: qcom,geniqup0@8c0000 {

I don't see a reason for this to be referenced, so skip the label. And
don't use qcom, in the node name; "geni" would be perfectly fine?

> +		compatible = "qcom,geni-se-qup";
> +		reg = <0x8c0000 0x6000>;
> +		clock-names = "m-ahb", "s-ahb";
> +		clocks = <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> +			<&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> +	}

Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux