Add device tree binding support for GENI based UART Controller in the
QUP Wrapper.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>
Signed-off-by: Girish Mahadevan <girishm@xxxxxxxxxxxxxx>
---
.../devicetree/bindings/serial/qcom,geni-uart.txt | 29 ++++++++++++++++++++++
.../devicetree/bindings/soc/qcom/qcom,geni-se.txt | 13 ++++++++++
2 files changed, 42 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/qcom,geni-uart.txt
diff --git a/Documentation/devicetree/bindings/serial/qcom,geni-uart.txt b/Documentation/devicetree/bindings/serial/qcom,geni-uart.txt
new file mode 100644
index 0000000..e7b9e24
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/qcom,geni-uart.txt
@@ -0,0 +1,29 @@
+Qualcomm Technologies Inc. GENI Serial Engine based UART Controller
+
+The Generic Interface (GENI) Serial Engine based UART controller supports
+console use-cases and is supported only by GENI based Qualcomm Universal
+Peripheral (QUP) cores.
+
+Required properties:
+- compatible: should contain "qcom,geni-debug-uart".
+- reg: Should contain UART register location and length.
+- reg-names: Should contain "se-phys".
+- interrupts: Should contain UART core interrupts.
+- clock-names: Should contain "se-clk".
+- clocks: clocks needed for UART, includes the core clock.
+- pinctrl-names/pinctrl-0/1: The GPIOs assigned to this core. The names
+ Should be "active" and "sleep" for the pin confuguration when core is active
+ or when entering sleep state.
+
+Example:
+uart0: qcom,serial@a88000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0xa88000 0x7000>;
+ reg-names = "se-phys";
+ interrupts = <0 355 0>;
+ clock-names = "se-clk";
+ clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_1_uart_3_active>;
+ pinctrl-1 = <&qup_1_uart_3_sleep>;
+};
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
index 2ffbb3e..c307788 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
@@ -26,6 +26,7 @@ controller, spi controller, or some combination of aforementioned devices.
See the following documentation for child node definitions:
Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
+Documentation/devicetree/bindings/serial/qcom,geni-uart.txt
Example:
qup0: qcom,geniqup0@8c0000 {
@@ -50,4 +51,16 @@ Example:
#address-cells = <1>;
#size-cells = <0>;
};
+
+ uart0: qcom,serial@a88000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0xa88000 0x7000>;
+ reg-names = "se-phys";
+ interrupts = <0 355 0>;
+ clock-names = "se-clk";
+ clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_1_uart_3_active>;
+ pinctrl-1 = <&qup_1_uart_3_sleep>;
+ };
}
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
