On 2017-12-05 10:15, Bjorn Andersson wrote:
On Thu 16 Nov 04:18 PST 2017, Kiran Gunda wrote:
WLED peripheral has over voltage protection(OVP) circuitry and the OVP
fault is notified through an interrupt. Though this fault condition
rising
is due to an incorrect hardware configuration is mitigated in the
hardware,
it still needs to be detected and handled. Add support for it.
When WLED module is enabled, keep OVP fault interrupt disabled for 10
ms to
account for soft start delay.
Signed-off-by: Kiran Gunda <kgunda@xxxxxxxxxxxxxx>
---
.../bindings/leds/backlight/qcom-spmi-wled.txt | 7 +-
drivers/video/backlight/qcom-spmi-wled.c | 83
++++++++++++++++++++++
2 files changed, 87 insertions(+), 3 deletions(-)
diff --git
a/Documentation/devicetree/bindings/leds/backlight/qcom-spmi-wled.txt
b/Documentation/devicetree/bindings/leds/backlight/qcom-spmi-wled.txt
index 768608c..d39ee93 100644
---
a/Documentation/devicetree/bindings/leds/backlight/qcom-spmi-wled.txt
+++
b/Documentation/devicetree/bindings/leds/backlight/qcom-spmi-wled.txt
@@ -92,7 +92,7 @@ The PMIC is connected to the host processor via SPMI
bus.
Usage: optional
Value type: <string>
Definition: Interrupt names associated with the interrupts.
- Must be "sc-irq".
+ Currently supported interrupts are "sc-irq" and "ovp-irq".
As before, we know this is an IRQ, so omit the -irq from the name.
[..]
Sure. Will change it in the next series.
diff --git a/drivers/video/backlight/qcom-spmi-wled.c
b/drivers/video/backlight/qcom-spmi-wled.c
[..]
@@ -115,6 +123,28 @@ static int qcom_wled_module_enable(struct
qcom_wled *wled, int val)
rc = regmap_update_bits(wled->regmap, wled->ctrl_addr +
QCOM_WLED_CTRL_MOD_ENABLE, QCOM_WLED_CTRL_MOD_EN_MASK,
val << QCOM_WLED_CTRL_MODULE_EN_SHIFT);
+ if (rc < 0)
+ return rc;
+ /*
+ * Wait for at least 10ms before enabling OVP fault interrupt after
+ * enabling the module so that soft start is completed. Keep the OVP
+ * interrupt disabled when the module is disabled.
+ */
+ if (val) {
+ usleep_range(QCOM_WLED_SOFT_START_DLY_US,
+ QCOM_WLED_SOFT_START_DLY_US + 1000);
This is sleeping in the brightness/enable code path, can you
schedule_delayed_work() instead to not block this code path
unnecessarily?
Sure. Will change it in the next series.
+
+ if (wled->cfg.ovp_irq > 0 && wled->ovp_irq_disabled) {
+ enable_irq(wled->cfg.ovp_irq);
+ wled->ovp_irq_disabled = false;
+ }
+ } else {
+ if (wled->cfg.ovp_irq > 0 && !wled->ovp_irq_disabled) {
+ disable_irq(wled->cfg.ovp_irq);
+ wled->ovp_irq_disabled = true;
+ }
+ }
+
return rc;
}
@@ -264,12 +294,42 @@ static irqreturn_t qcom_wled_sc_irq_handler(int
irq, void *_wled)
return IRQ_HANDLED;
}
+static irqreturn_t qcom_wled_ovp_irq_handler(int irq, void *_wled)
+{
+ struct qcom_wled *wled = _wled;
+ int rc;
+ u32 int_sts, fault_sts;
+
+ rc = regmap_read(wled->regmap,
+ wled->ctrl_addr + QCOM_WLED_CTRL_INT_RT_STS, &int_sts);
+ if (rc < 0) {
+ pr_err("Error in reading WLED_INT_RT_STS rc=%d\n", rc);
+ return IRQ_HANDLED;
+ }
+
+ rc = regmap_read(wled->regmap, wled->ctrl_addr +
+ QCOM_WLED_CTRL_FAULT_STATUS, &fault_sts);
+ if (rc < 0) {
+ pr_err("Error in reading WLED_FAULT_STATUS rc=%d\n", rc);
+ return IRQ_HANDLED;
+ }
+
+ if (fault_sts &
+ (QCOM_WLED_CTRL_OVP_FAULT_BIT | QCOM_WLED_CTRL_ILIM_FAULT_BIT))
+ pr_err("WLED OVP fault detected, int_sts=%x fault_sts= %x\n",
+ int_sts, fault_sts);
All this function does is print things to the log. When is this
information consumed and by whom? dev_dbg() instead?
Sure. Will change it in the next series.
+
+ return IRQ_HANDLED;
+}
+
static int qcom_wled_setup(struct qcom_wled *wled)
{
int rc, temp, i;
u8 sink_en = 0;
+ u32 val;
u8 string_cfg = wled->cfg.string_cfg;
int sc_irq = wled->cfg.sc_irq;
+ int ovp_irq = wled->cfg.ovp_irq;
rc = regmap_update_bits(wled->regmap,
wled->ctrl_addr + QCOM_WLED_CTRL_OVP,
@@ -367,6 +427,25 @@ static int qcom_wled_setup(struct qcom_wled
*wled)
}
}
+ if (ovp_irq >= 0) {
As with the previous patch.
[..]
Sure. Will change it in the next series.
@@ -539,6 +618,10 @@ static int qcom_wled_configure(struct qcom_wled
*wled, struct device *dev)
[..]
+ wled->cfg.ovp_irq = platform_get_irq_byname(wled->pdev, "ovp-irq");
+ if (wled->cfg.ovp_irq < 0)
+ dev_dbg(&wled->pdev->dev, "ovp irq is not used\n");
+
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
