Re: [PATCH 5/5 v2] clk: qcom: Add support for MSM8660 LCC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 05/30, Bjorn Andersson wrote:
> On Mon 29 May 05:23 PDT 2017, Linus Walleij wrote:
> 
> > On Sat, May 27, 2017 at 10:19 PM, Bjorn Andersson
> > <bjorn.andersson@xxxxxxxxxx> wrote:
> > > On Wed 19 Apr 02:13 PDT 2017, Linus Walleij wrote:
> > >> diff --git a/drivers/clk/qcom/lcc-msm8660.c b/drivers/clk/qcom/lcc-msm8660.c
> > > [..]
> > >> +/* The vendor code uses PLL4 as parent everywhere */
> > >> +static const struct parent_map lcc_parent_map[] = {
> > >> +     { P_PXO, 0 },
> > >> +     { P_CXO, 1 },
> > >> +     /* Select RPM PLL4, but also used for selecting LPA PLL0 */
> > >> +     { P_PLL4_LPA_PLL0, 2 },
> > >> +     /* Will just ground the line */
> > >> +     { P_GND, 6 },
> > >> +};
> > >> +
> > >> +static const char * const lcc_parent_tbl[] = {
> > >> +     "pxo",
> > >> +     "cxo",
> > >> +     /*
> > >> +      * PLL4 is an RPM clock on MSM8660/APQ8060, set to "pll4" for this
> > >> +      * If we enable and mux in the LPA_PLL0 on this platform, we can
> > >> +      * set this to "lpa_pll0" instead
> > >> +      */
> > >> +     "pll4_clk",
> > >> +     "gnd", /* This is a very inactive parent */
> > >> +};
> > >> +
> > >> +/*
> > >> + * This table is evidently for using PLL4 as parent, if we start using
> > >> + * LPA_PLL0 we need to provide a second table.
> > >> + */
> > >
> > > Aren't you muxing in LPA_PLL0 as source instead of PLL4 at the bottom of
> > > probe()? And as you hard code that selector, shouldn't the parent table
> > > reference lpa_pll0?
> > 
> > I think it's just a naming problem.
> > 
> > I'm actually using:
> > 
> > >> +     {   768000, P_PLL4_LPA_PLL0, 4,  1, 176 },
> > 
> > Because as far as I can tell, RPM clock PLL4 and LPA_PLL0 is the
> > same thing, just different names.
> > 
> > I don't think the 8660 has its own LPA PLL, it's just the layers of
> > confusion in the code that make it seem like so.
> > 
> > Or maybe someone was in the planning stages of adding the LPA PLL
> > to the hardware and never got there. So some code confusingly
> > refers to that...
> > 
> > I would really like to see how it actually works.
> > 
> 
> 8660 and 8960 are basically different revisions of the same SoC, so
> reviewing clock-8x60.c and clock-8960.c found in below repository gives
> some additional insight.
> 
> clock-8x60.c mentions LPA_PLL0 in _one_ comment and carries the
> definitions for a LCC_PLL0 clock, but no references are made to these
> defines. The code ever only references "pll4".
> 
> clock-8960.c goes beyond this and actually reference the LCC_PLL0
> registers and they are all used to query and configure "pll4".
> 
> 
> So AFAICT PLL4 is controlled/implemented in the LCC block and is called
> PLL0 in that context and that on 8660 it's completely controlled by the
> RPM.
> 
> As such I think it makes sense - on 8660 - to just reference "pll4",
> perhaps with some comment in the code referencing LCC_PLL0 as the actual
> implementation.

Correct, LCC_PLL0 is a local naming scheme for the audio clock
controller's 0th PLL. That just so happens to be PLL4 "globally"
in the SoC. From global clock control standpoint it's PLL4. I
would just reference PLL4 everywhere and ignore the whole
LCC_PLL0 thing.

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux