Re: [RESEND: PATCH v4 3/4] remoteproc: qcom: Make secure world call for mem ownership switch

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue 16 May 11:02 PDT 2017, Avaneesh Kumar Dwivedi wrote:

> +static int q6v5_assign_mem_to_subsys(struct q6v5 *qproc,
> +		phys_addr_t addr, size_t size)
> +{
> +	struct qcom_scm_destVmPerm next[] = {{ QCOM_SCM_VMID_MSS_MSA,
> +		(QCOM_SCM_PERM_READ | QCOM_SCM_PERM_WRITE)} };

struct qcom_scm_destVmPerm next = {
	.vmid = QCOM_SCM_VMID_MSS_MSA,
	.perm = QCOM_SCM_PERM_RW
};

> +	int ret;
> +
> +	size = ALIGN(size, SZ_4K);

I believe it will be cleaner if you just put this alignment directly in
the function call below.

> +	if (!qproc->need_mem_protection)
> +		return 0;

Put a blank line here, to give separation between the sections of the
function.

> +	ret = qcom_scm_assign_mem(addr, size,
> +		BIT(QCOM_SCM_VMID_HLOS), next, sizeof(next));

	qcom_scm_assign_mem(addr, ALIGN(size, SZ_4K),
			    BIT(QCOM_SCM_VMID_HLOS), &next, 1);

> +	if (ret)
> +		pr_err("%s: Failed to assign memory access, ret = %d\n",
> +			__func__, ret);

There's no point in printing an error here and in the calling function,
but as it makes sense to have the error message to include which memory
region we operated on (mba vs mpss) I think you should remove the print
here and keep it in the callers.

So just return qcom-scm_assign_mem().

> +	return ret;
> +}
> +
> +static int q6v5_assign_mem_to_linux(struct q6v5 *qproc,
> +		phys_addr_t addr, size_t size)
> +{
> +	struct qcom_scm_destVmPerm next[] = { { QCOM_SCM_VMID_HLOS,
> +		(QCOM_SCM_PERM_READ | QCOM_SCM_PERM_WRITE | QCOM_SCM_PERM_EXEC)}
> +		};

struct qcom_scm_destVmPerm next = {
	.vmid = QCOM_SCM_VMID_HLOS,
	.perm = QCOM_SCM_PERM_RWX,
};

(And add RWX to the list of defines in patch 1)

[..]
> @@ -471,6 +517,11 @@ static int q6v5_mpss_init_image(struct q6v5 *qproc, const struct firmware *fw)
>  		dev_err(qproc->dev,
>  			"metadata authentication failed: %d\n", ret);
>  
> +	/* Metadata authentication done, remove modem access */
> +	ret = q6v5_assign_mem_to_linux(qproc, phys, fw->size);
> +	if (ret)
> +		dev_err(qproc->dev,
> +			"Failed to reclaim metadata memory, ret - %d\n", ret);

If this assignment fails (for any reason) we can't return the memory to
the free pool in Linux, because at some point in the future these pages
will be allocated to someone else resulting in a memory access violation
scenario that will be just terrible to debug.

I do however not have a better idea at the moment than just leaking the
memory.

>  	dma_free_attrs(qproc->dev, fw->size, ptr, phys, dma_attrs);
>  
>  	return ret < 0 ? ret : 0;
[..]
> @@ -656,16 +719,21 @@ static int q6v5_start(struct rproc *rproc)
>  
>  	ret = q6v5_mpss_load(qproc);
>  	if (ret)
> -		goto halt_axi_ports;
> +		goto reclaim_mem;

This doesn't allow us to distinguish between failures before or after
the memory assignment in mpss_load(), so although you're duplicating the
reclaim code, mpss_load() must be responsible of restoring the state on
failure.

The timeout below still has to reclaim the memory.

>  
>  	ret = wait_for_completion_timeout(&qproc->start_done,
>  					  msecs_to_jiffies(5000));
>  	if (ret == 0) {
>  		dev_err(qproc->dev, "start timed out\n");
>  		ret = -ETIMEDOUT;
> -		goto halt_axi_ports;
> +		goto reclaim_mem;
>  	}
>  
> +	ret = q6v5_assign_mem_to_linux(qproc,
> +		qproc->mba_phys, qproc->mba_size);
> +	if (ret)
> +		dev_err(qproc->dev,
> +			"Failed to reclaim mba memory, ret - %d\n", ret);

I think it's okay for symmetrical purposes to keep the memory assigned
to the remote until we call stop().

Although this shows that we should be able to release the mba allocation
here.

>  	qproc->running = true;
>  
>  	q6v5_clk_disable(qproc->dev, qproc->proxy_clks,
> @@ -675,12 +743,19 @@ static int q6v5_start(struct rproc *rproc)
>  
>  	return 0;
>  
> +reclaim_mem:
> +	assign_mem_result =
> +		q6v5_assign_mem_to_linux(qproc,
> +		qproc->mpss_phys, qproc->mpss_size);

If this fails we're screwed. We have no way to fail in a way that will
not free the memory at any later point in time.

So I do believe you should have a BUG_ON(assign_mem_result); here. With
a clear comment in the lines of:

/*
 * Failed to reclaim memory, any future access to these pages will cause
 * security violations and a seemingly random crash
 */

>  halt_axi_ports:
>  	q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_q6);
>  	q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem);
>  	q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc);
>  	q6v5_clk_disable(qproc->dev, qproc->active_clks,
>  			 qproc->active_clk_count);
> +	assign_mem_result =
> +		q6v5_assign_mem_to_linux(qproc,
> +		qproc->mba_phys, qproc->mba_size);

Shouldn't we move them even further down?

Same BUG_ON() as above.

>  assert_reset:
>  	reset_control_assert(qproc->mss_restart);
>  disable_vdd:

Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux