Hi Sricharan, Robin,
On Wed, May 3, 2017 at 12:24 PM, Sricharan R <sricharan@xxxxxxxxxxxxxx> wrote:
> On 5/3/2017 3:24 PM, Robin Murphy wrote:
>> On 02/05/17 19:35, Geert Uytterhoeven wrote:
>>> On Fri, Feb 3, 2017 at 4:48 PM, Sricharan R <sricharan@xxxxxxxxxxxxxx> wrote:
>>>> From: Laurent Pinchart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
>>>>
>>>> Failures to look up an IOMMU when parsing the DT iommus property need to
>>>> be handled separately from the .of_xlate() failures to support deferred
>>>> probing.
>>>>
>>>> The lack of a registered IOMMU can be caused by the lack of a driver for
>>>> the IOMMU, the IOMMU device probe not having been performed yet, having
>>>> been deferred, or having failed.
>>>>
>>>> The first case occurs when the device tree describes the bus master and
>>>> IOMMU topology correctly but no device driver exists for the IOMMU yet
>>>> or the device driver has not been compiled in. Return NULL, the caller
>>>> will configure the device without an IOMMU.
>>>>
>>>> The second and third cases are handled by deferring the probe of the bus
>>>> master device which will eventually get reprobed after the IOMMU.
>>>>
>>>> The last case is currently handled by deferring the probe of the bus
>>>> master device as well. A mechanism to either configure the bus master
>>>> device without an IOMMU or to fail the bus master device probe depending
>>>> on whether the IOMMU is optional or mandatory would be a good
>>>> enhancement.
>>>>
>>>> Tested-by: Marek Szyprowski <m.szyprowski@xxxxxxxxxxx>
>>>> Signed-off-by: Laurent Pichart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
>>>> Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
>>>
>>> This patch broke Renesas R-Car Gen3 platforms in renesas-drivers.
>>> As the IOMMU nodes in DT are not yet enabled, all devices having iommus
>>> properties in DT now fail to probe.
>>
>> How exactly do they fail to probe? Per d7b0558230e4, if there are no ops
>> registered then they should merely defer until we reach the point of
>> giving up and ignoring the IOMMU. Is it just that you have no other
>> late-probing drivers or post-init module loads to kick the deferred
>> queue after that point? I did try to find a way to explicitly kick it
>> from a suitably late initcall, but there didn't seem to be any obvious
>> public interface - anyone have any suggestions?
>>
>> I think that's more of a general problem with the probe deferral
>> mechanism itself (I've seen the same thing happen with some of the
>> CoreSight stuff on Juno due to the number of inter-component
>> dependencies) rather than any specific fault of this series.
I had a deeper look into the issue.
What changed, is that of_dma_configure() now returns an error code,
and dma_configure() looks at it.
Actually there are two failure modes:
1. Devices with an iommus property pointing to a disabled IOMMU node.
These return -EPROBE_DEFER, and are now retried forever.
2. Devices that are blacklisted in the IPMMU driver, as we don't want to
use them with an IOMMU yet.
These return -ENODEV, due to ipmmu_of_xlate_dma().
> I was thinking of an additional check like below to avoid the
> situation ?
>
> From 499b6e662f60f23740b8880882b0a16f16434501 Mon Sep 17 00:00:00 2001
> From: Sricharan R <sricharan@xxxxxxxxxxxxxx>
> Date: Wed, 3 May 2017 13:16:59 +0530
> Subject: [PATCH] iommu: of: Fix check for returning EPROBE_DEFER
>
> While returning EPROBE_DEFER for iommu masters
> take in to account of iommu nodes that could be
> marked in DT as 'status=disabled', in which case
> simply return NULL and let the master's probe
> continue rather than deferring.
>
> Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
> ---
> drivers/iommu/of_iommu.c | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/drivers/iommu/of_iommu.c b/drivers/iommu/of_iommu.c
> index 9f44ee8..e6e9bec 100644
> --- a/drivers/iommu/of_iommu.c
> +++ b/drivers/iommu/of_iommu.c
> @@ -118,6 +118,7 @@ static bool of_iommu_driver_present(struct device_node *np)
>
> ops = iommu_ops_from_fwnode(fwnode);
> if ((ops && !ops->of_xlate) ||
> + !of_device_is_available(iommu_spec->np) ||
> (!ops && !of_iommu_driver_present(iommu_spec->np)))
> return NULL;
Thanks, this fixes the first class of failures.
The second class can be worked around using:
--- a/drivers/iommu/of_iommu.c
+++ b/drivers/iommu/of_iommu.c
@@ -196,6 +196,11 @@ static const struct iommu_ops
ops = of_iommu_xlate(dev, &iommu_spec);
of_node_put(iommu_spec.np);
idx++;
+ if (PTR_ERR(ops) == -ENODEV) {
+ dev_info(dev, "%s: Ignoring -ENODEV => NULL\n",
+ __func__);
+ return NULL;
+ }
if (IS_ERR_OR_NULL(ops))
break;
}
but obviously that's too hackish to apply...
Magnus, do you have a suggestion?
Thanks!
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
