On Sat 08 Apr 06:39 PDT 2017, Pavel Machek wrote: > Hi! > > > [..] > > > > For the patterns I don't know how a trigger for this would look like, > > > > how would setting the pattern of a trigger be propagated down to the > > > > hardware? > > > > > > We'd need a new op and API similar to blink_set()/led_blink_set(). > > > > > > > I've tried to find different LED circuits with some sort of pattern > > generator in an attempt to figure out how to design this interface, but > > turned out to be quite hard to find examples; the three I can compare > > are: > > > > * LP5xx series "implements" pattern generation by executing code. > > > > * Qualcomm LPG iterates over 2-64 brightness-values in a pattern, at a > > fixed rate with knobs to configure what happens before starting and > > after finishing iterating over the defined values. It does not support > > smooth transitions between values. > > > > * AS3676 supports a pattern of 32 values controlling if the output > > should be enabled or disabled for each 32.5ms (or 250ms) time period. > > The delay before repeating the pattern can be configured. It support > > smooth transitions between the states. > > > > > > So, while I think I see how you would like to architect this interface I > > am not sure how to figure out the details. > > > > The pattern definition would have to be expressive enough to support the > > features of LP5xx and direct enough to support the limited AS3676. It > > would likely have to express transitions, so that the LPG could generate > > intermediate steps (and we will have to adapt the resolution of the > > ramps based on the other LPGs in the system). > > > > How do we do with patterns that are implementable by the LP5xx but are > > not with the LPG? Should we reject those or should we do some sort of > > best-effort approach in the kernel? > > Lets say you get series of > > (red, green, blue, delta_t ) > > points, meaning "in delta_t msec, change color to red, green, > blue. Lets ignore other channels for now. delta_t of 0 would be step > change. Would such interface work for you? > So I presume this would be input to the RGB trigger that we discussed. But in my current device I have 6 LEDs, that are not in any RGB-like configuration. So we would need to come up with an interface that looks to be the same in both single-LED and RGB-LED setups. This should be sufficient to describe a subset of the patterns I've seen so far in products. But let's consider the standard use case for an RGB LED on an Android phone; continuously blinking (pulsing based on patterns) as you have some notifications waiting. In this case you want the LED hardware to do all the work, so that you can deep-idle the CPU. So we would need to introduce a "repeat pattern"-command. Then consider the fact that you want your patterns to have decent resolution, but you have a limited amount of storage. So we either have to be able to detect palindromes or have a way to represent this. > Simple compiler from this to LP5XX code should not be hard to > do. It sounds fairly straight forward to convert a pattern to instructions, but we do have an extremely limited amount of storage so it must be a quite good implementation for people to be able to use it for anything real. We could implement some optimization steps where we try to detect slopes and generate ramp-instructions instead of set-pwm + wait instructions, use some variables to handle ramp up/down and we could probably generate some jump instructions to implement loops. But do we really want this logic in the kernel, for each LED chip supporting patterns? > AS3676 ... I'm not sure what to do, AFAICT it is too limited. > So out of the three examples I've looked at we're skipping one and we're abstracting away most functionality from another. I'm sorry for being pessimistic about this, but while I can see the theoretical benefit of providing a uniform interface for this to user space I see three very different pieces of hardware that would be used in three different ways in products. Regards, Bjorn -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
