Qualcomm chipsets have QUSB2 phy controller that provides
HighSpeed functionality for DWC3 controller.
Adding dt binding information for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@xxxxxxxxxxxxxx>
Acked-by: Rob Herring <robh@xxxxxxxxxx>
---
Changes since v6:
- Dropped 'vdd-phy-supply' that used pm8994_s2 regulator, from bindings.
As Stephen said, the pm8994_s2 is a 'corner' regulator and it shouldn't
be right to put it as a regulator supply.
Work is in progress to handle these sort of power supplies.
Changes since v5:
- Removed leading 0 from the address in 'reg' property.
Changes since v4:
- None.
Changes since v3:
- Added 'Acked-by' from Rob.
- Removed 'reset-names' and 'nvmem-cell-names' from the bindings
since we use only one cell.
Changes since v2:
- Removed binding for "ref_clk_src" since we don't request this
clock in the driver.
- Addressed s/vdda-phy-dpdm/vdda-phy-dpdm-supply.
- Addressed s/ref_clk/ref. Don't need to add '_clk' suffix to clock names.
- Addressed s/tune2_hstx_trim_efuse/tune2_hstx_trim. Don't need to add
'efuse' suffix to nvmem cell.
- Addressed s/qusb2phy/phy for the node name.
Changes since v1:
- New patch, forked out of the original driver patch:
"phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips"
- Updated dt bindings to remove 'hstx-trim-bit-offset' and
'hstx-trim-bit-len' bindings.
.../devicetree/bindings/phy/qcom-qusb2-phy.txt | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
new file mode 100644
index 000000000000..aa0fcb05acb3
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -0,0 +1,43 @@
+Qualcomm QUSB2 phy controller
+=============================
+
+QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
+
+Required properties:
+ - compatible: compatible list, contains "qcom,msm8996-qusb2-phy".
+ - reg: offset and length of the PHY register set.
+ - #phy-cells: must be 0.
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: must be "cfg_ahb" for phy config clock,
+ "ref" for 19.2 MHz ref clk,
+ "iface" for phy interface clock (Optional).
+
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+ - vdda-phy-dpdm-supply: Phandle to 3.1V regulator supply to Dp/Dm port signals.
+
+ - resets: Phandle to reset to phy block.
+
+Optional properties:
+ - nvmem-cells: Phandle to nvmem cell that contains 'HS Tx trim'
+ tuning parameter value for qusb2 phy.
+
+ - qcom,tcsr-syscon: Phandle to TCSR syscon register region.
+
+Example:
+ hsusb_phy: phy@7411000 {
+ compatible = "qcom,msm8996-qusb2-phy";
+ reg = <0x7411000 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_RX1_USB2_CLKREF_CLK>,
+ clock-names = "cfg_ahb", "ref";
+
+ vdda-pll-supply = <&pm8994_l12>;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+ nvmem-cells = <&qusb2p_hstx_trim>;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
