The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-adc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).
As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.
This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.
Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.
Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
Cc: linux-arm-msm@xxxxxxxxxxxxxxx
Cc: Ivan T. Ivanov <iivanov.xz@xxxxxxxxx>
Cc: Andy Gross <andy.gross@xxxxxxxxxx>
Cc: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
Cc: Stephen Boyd <sboyd@xxxxxxxxxxxxxx>
Cc: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
Cc: Rama Krishna Phani A <rphani@xxxxxxxxxxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
ChangeLog v3->v4:
- Only reposting this patch as the DT bindings and refactorings
are merged.
- Prefix all channel names with PM8XXX_* to avoid namespace clashes.
- Use the compatible string to name the IIO device for greater
model precision.
- Fix up a few excess newlines.
ChangeLog v2->v3:
- Rebase using Rama Krishna's improvements, set up defaults for
scaling function and prescaler for each channel, per ASIC variant.
- Also set up RSV per-variant as the vendor tree does this and
it seems necessary to set RSV0 on the muxoff channel to get
readings from the XO thermistor.
- Encode default IIO type in the default per-PMIC channel table.
- Fixed a bug in ratiometric calibration (needed to force ratiometric
mode).
- Dropped PM8917: that doesn't have any XOADC.
- Added a special flag for the PM8058: it apparently needs special
RSV muxing due to being necessarily different.
- Augmented to handle altered ratiometric DT property.
- Do not hardcode that the reference voltage must be 2.2V, just fetch
and enable the regulator. Different PMICs use different reference
voltages.
ChangeLog v1->v2:
- Introduce a mutex to avoid different clients stepping on each others'
toes
- Add an of_xlate function to be sure to match the right ADC
- Add all compatible strings, not just PM8058
---
drivers/iio/adc/Kconfig | 10 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/qcom-pm8xxx-xoadc.c | 930 ++++++++++++++++++++++++++++++++++++
3 files changed, 941 insertions(+)
create mode 100644 drivers/iio/adc/qcom-pm8xxx-xoadc.c
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 817693a14eb9..3184e36b1987 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -421,6 +421,16 @@ config PALMAS_GPADC
is used in smartphones and tablets and supports a 16 channel
general purpose ADC.
+config QCOM_PM8XXX_XOADC
+ tristate "Qualcomm SSBI PM8xxx PMIC XOADCs"
+ depends on MFD_PM8XXX
+ help
+ ADC driver for the XOADC portions of the Qualcomm PM8xxx PMICs
+ using SSBI transport: PM8018, PM8038, PM8058, PM8921.
+
+ To compile this driver as a module, choose M here: the module
+ will be called qcom-pm8xxx-xoadc.
+
config QCOM_SPMI_IADC
tristate "Qualcomm SPMI PMIC current ADC"
depends on SPMI
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index f8fe647b7abe..8d2b80cdcb6f 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
qcom-vadc-y := qcom-vadc-common.o
obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-vadc.o qcom-spmi-vadc.o
+obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-vadc.o qcom-pm8xxx-xoadc.o
obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o
obj-$(CONFIG_STX104) += stx104.o
obj-$(CONFIG_STM32_ADC_CORE) += stm32-adc-core.o
diff --git a/drivers/iio/adc/qcom-pm8xxx-xoadc.c b/drivers/iio/adc/qcom-pm8xxx-xoadc.c
new file mode 100644
index 000000000000..fdc85fb88204
--- /dev/null
+++ b/drivers/iio/adc/qcom-pm8xxx-xoadc.c
@@ -0,0 +1,930 @@
+/*
+ * Qualcomm PM8xxx PMIC XOADC driver
+ *
+ * These ADCs are known as HK/XO (house keeping / chrystal oscillator)
+ * "XO" in "XOADC" means Chrystal Oscillator. It's a bunch of
+ * specific-purpose and general purpose ADC converters and channels.
+ *
+ * Copyright (C) 2016 Linaro Ltd.
+ * Author: Linus Walleij <linus.walleij@xxxxxxxxxx>
+ */
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/regulator/consumer.h>
+
+#include "qcom-vadc-common.h"
+
+/*
+ * Definitions for the "user processor" registers lifted from the v3.4
+ * Qualcomm tree. Their kernel has two out-of-tree drivers for the ADC:
+ * drivers/misc/pmic8058-xoadc.c
+ * drivers/hwmon/pm8xxx-adc.c
+ * None of them contain any complete register specification, so this is
+ * a best effort of combining the information.
+ */
+
+/* These appear to be "battery monitor" registers */
+#define ADC_ARB_BTM_CNTRL1 0x17e
+#define ADC_ARB_BTM_CNTRL1_EN_BTM BIT(0)
+#define ADC_ARB_BTM_CNTRL1_SEL_OP_MODE BIT(1)
+#define ADC_ARB_BTM_CNTRL1_MEAS_INTERVAL1 BIT(2)
+#define ADC_ARB_BTM_CNTRL1_MEAS_INTERVAL2 BIT(3)
+#define ADC_ARB_BTM_CNTRL1_MEAS_INTERVAL3 BIT(4)
+#define ADC_ARB_BTM_CNTRL1_MEAS_INTERVAL4 BIT(5)
+#define ADC_ARB_BTM_CNTRL1_EOC BIT(6)
+#define ADC_ARB_BTM_CNTRL1_REQ BIT(7)
+
+#define ADC_ARB_BTM_AMUX_CNTRL 0x17f
+#define ADC_ARB_BTM_ANA_PARAM 0x180
+#define ADC_ARB_BTM_DIG_PARAM 0x181
+#define ADC_ARB_BTM_RSV 0x182
+#define ADC_ARB_BTM_DATA1 0x183
+#define ADC_ARB_BTM_DATA0 0x184
+#define ADC_ARB_BTM_BAT_COOL_THR1 0x185
+#define ADC_ARB_BTM_BAT_COOL_THR0 0x186
+#define ADC_ARB_BTM_BAT_WARM_THR1 0x187
+#define ADC_ARB_BTM_BAT_WARM_THR0 0x188
+#define ADC_ARB_BTM_CNTRL2 0x18c
+
+/* Proper ADC registers */
+
+#define ADC_ARB_USRP_CNTRL 0x197
+#define ADC_ARB_USRP_CNTRL_EN_ARB BIT(0)
+#define ADC_ARB_USRP_CNTRL_RSV1 BIT(1)
+#define ADC_ARB_USRP_CNTRL_RSV2 BIT(2)
+#define ADC_ARB_USRP_CNTRL_RSV3 BIT(3)
+#define ADC_ARB_USRP_CNTRL_RSV4 BIT(4)
+#define ADC_ARB_USRP_CNTRL_RSV5 BIT(5)
+#define ADC_ARB_USRP_CNTRL_EOC BIT(6)
+#define ADC_ARB_USRP_CNTRL_REQ BIT(7)
+
+#define ADC_ARB_USRP_AMUX_CNTRL 0x198
+#define ADC_ARB_USRP_AMUX_CNTRL_RSV0 BIT(0)
+#define ADC_ARB_USRP_AMUX_CNTRL_RSV1 BIT(1)
+#define ADC_ARB_USRP_AMUX_CNTRL_PREMUX0 BIT(2)
+#define ADC_ARB_USRP_AMUX_CNTRL_PREMUX1 BIT(3)
+#define ADC_ARB_USRP_AMUX_CNTRL_SEL0 BIT(4)
+#define ADC_ARB_USRP_AMUX_CNTRL_SEL1 BIT(5)
+#define ADC_ARB_USRP_AMUX_CNTRL_SEL2 BIT(6)
+#define ADC_ARB_USRP_AMUX_CNTRL_SEL3 BIT(7)
+#define ADC_AMUX_PREMUX_SHIFT 2
+#define ADC_AMUX_SEL_SHIFT 4
+
+/* We know very little about the bits in this register */
+#define ADC_ARB_USRP_ANA_PARAM 0x199
+#define ADC_ARB_USRP_ANA_PARAM_DIS 0xFE
+#define ADC_ARB_USRP_ANA_PARAM_EN 0xFF
+
+#define ADC_ARB_USRP_DIG_PARAM 0x19A
+#define ADC_ARB_USRP_DIG_PARAM_SEL_SHIFT0 BIT(0)
+#define ADC_ARB_USRP_DIG_PARAM_SEL_SHIFT1 BIT(1)
+#define ADC_ARB_USRP_DIG_PARAM_CLK_RATE0 BIT(2)
+#define ADC_ARB_USRP_DIG_PARAM_CLK_RATE1 BIT(3)
+#define ADC_ARB_USRP_DIG_PARAM_EOC BIT(4)
+/*
+ * On a later ADC the decimation factors are defined as
+ * 00 = 512, 01 = 1024, 10 = 2048, 11 = 4096 so assume this
+ * holds also for this older XOADC.
+ */
+#define ADC_ARB_USRP_DIG_PARAM_DEC_RATE0 BIT(5)
+#define ADC_ARB_USRP_DIG_PARAM_DEC_RATE1 BIT(6)
+#define ADC_ARB_USRP_DIG_PARAM_EN BIT(7)
+#define ADC_DIG_PARAM_DEC_SHIFT 5
+
+#define ADC_ARB_USRP_RSV 0x19B
+#define ADC_ARB_USRP_RSV_RST BIT(0)
+#define ADC_ARB_USRP_RSV_DTEST0 BIT(1)
+#define ADC_ARB_USRP_RSV_DTEST1 BIT(2)
+#define ADC_ARB_USRP_RSV_OP BIT(3)
+#define ADC_ARB_USRP_RSV_IP_SEL0 BIT(4)
+#define ADC_ARB_USRP_RSV_IP_SEL1 BIT(5)
+#define ADC_ARB_USRP_RSV_IP_SEL2 BIT(6)
+#define ADC_ARB_USRP_RSV_TRM BIT(7)
+#define ADC_RSV_IP_SEL_SHIFT 4
+
+#define ADC_ARB_USRP_DATA0 0x19D
+#define ADC_ARB_USRP_DATA1 0x19C
+
+/**
+ * Physical channels, the vendor tree call these "channel path type"
+ * for some reason, they have pretty much hardwired characteristics.
+ * MPP = Multi-Purpose Pin. Channel info:
+ *
+ * @PM8XXX_CHANNEL_VCOIN: Coincell backup power source
+ * @PM8XXX_CHANNEL_VBAT: Battery voltage
+ * @PM8XXX_CHANNEL_DCIN: Charger voltage
+ * @PM8XXX_CHANNEL_ICHG: Charger current monitor
+ * @PM8XXX_CHANNEL_VPH_PWR: Main system power VPH
+ * @PM8XXX_CHANNEL_MPP5: general purpose, used for headset detection on some
+ * set-ups
+ * @PM8XXX_CHANNEL_MPP6: general purpose, used for battery temperature on some
+ * set-ups
+ * @PM8XXX_CHANNEL_MPP7: general purpose, used for system temperature on some
+ * set-ups
+ * @PM8XXX_CHANNEL_MPP8: general purpose, used for battery ID detection on
+ * some set-ups
+ * @PM8XXX_CHANNEL_MPP9: general purpose, used for external charger current on
+ * some set-ups
+ * @PM8XXX_CHANNEL_USB_VBUS: USB bus voltage, used for USB charging
+ * @PM8XXX_CHANNEL_DIE_TEMP: PMIC die temperature
+ * @PM8XXX_CHANNEL_INTERNAL: 625mV reference channel
+ * @PM8XXX_CHANNEL_125V: 1250mV reference channel
+ * @PM8XXX_CHANNEL_INTERNAL_2: 325mV reference channel
+ * @PM8XXX_CHANNEL_MUXOFF: channel to reduce input load on mux, apparently also
+ * measures XO temperature
+ */
+#define PM8XXX_CHANNEL_VCOIN 0x0
+#define PM8XXX_CHANNEL_VBAT 0x1
+#define PM8XXX_CHANNEL_DCIN 0x2
+#define PM8XXX_CHANNEL_ICHG 0x3
+#define PM8XXX_CHANNEL_VPH_PWR 0x4
+#define PM8XXX_CHANNEL_MPP5 0x5
+#define PM8XXX_CHANNEL_MPP6 0x6
+#define PM8XXX_CHANNEL_MPP7 0x7
+#define PM8XXX_CHANNEL_MPP8 0x8
+#define PM8XXX_CHANNEL_MPP9 0x9
+#define PM8XXX_CHANNEL_USB_VBUS 0xa
+#define PM8XXX_CHANNEL_DIE_TEMP 0xb
+#define PM8XXX_CHANNEL_INTERNAL 0xc
+#define PM8XXX_CHANNEL_125V 0xd
+#define PM8XXX_CHANNEL_INTERNAL_2 0xe
+#define PM8XXX_CHANNEL_MUXOFF 0xf
+
+#define XOADC_CHANNELS 16 /* 4 bits */
+
+/* MPP = Multi-Purpose Pins, premux scaling */
+#define MPP_SCALE_0 0x0 /* No scaling on the signal */
+#define MPP_SCALE_1 0x1 /* Unity scaling selected by the user */
+#define MPP_SCALE_1_DIV3 0x2 /* 1/3 prescaler on the input from MPP */
+
+/* Defines reference voltage for the XOADC */
+#define AMUX_RSV0 0x0 /* XO_IN/XOADC_GND, special selection to read XO temp */
+#define AMUX_RSV1 0x1 /* PMIC_IN/XOADC_GND */
+#define AMUX_RSV2 0x2 /* PMIC_IN/BMS_CSP */
+#define AMUX_RSV3 0x3 /* not used */
+#define AMUX_RSV4 0x4 /* XOADC_GND/XOADC_GND */
+#define AMUX_RSV5 0x5 /* XOADC_VREF/XOADC_GND */
+#define XOADC_RSV_MAX 5 /* 3 bits 0..7, 3 and 6,7 are invalid */
+
+/*
+ * The different hardware channel names, hardware characteristics
+ * and sensible default settings.
+ * @datasheet_name: the hardwarename of this channel
+ * @prescale: the channels have hard-coded prescale ratios defined
+ * by the hardware, this tells us what it is
+ * @type: corresponding IIO channel type, usually IIO_VOLTAGE or
+ * IIO_TEMP
+ * @scale_fn_type: the liner interpolation etc to convert the
+ * ADC code to the value that IIO expects, in uV or millicelsius
+ * etc. This scale function can be pretty elaborate if different
+ * thermistors are connected or other hardware characteristics are
+ * deployed.
+ * @amux_ip_rsv: ratiometric scale value used by the analig muxer: this
+ * selects the reference voltage for ratiometric scaling
+ */
+struct xoadc_channel {
+ const char *datasheet_name;
+ const struct vadc_prescale_ratio prescale;
+ enum iio_chan_type type;
+ enum vadc_scale_fn_type scale_fn_type;
+ u8 amux_ip_rsv:3;
+};
+
+#define XOADC_CHAN(_dname, _type, _prenum, _preden, _scale, _amip) \
+ [PM8XXX_CHANNEL_##_dname] = { \
+ .datasheet_name = __stringify(_dname), \
+ .prescale = { .num = _prenum, .den = _preden }, \
+ .type = _type, \
+ .scale_fn_type = _scale, \
+ .amux_ip_rsv = _amip, \
+ } \
+
+/*
+ * Taken from arch/arm/mach-msm/board-9615.c in the vendor tree:
+ * TODO: incomplete, needs testing.
+ */
+static const struct xoadc_channel pm8018_xoadc_channels[] = {
+ XOADC_CHAN(VCOIN, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(VBAT, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(VPH_PWR, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(DIE_TEMP, IIO_TEMP, 1, 1, SCALE_PMIC_THERM, AMUX_RSV1),
+ /* Used for battery ID or battery temperature */
+ XOADC_CHAN(MPP8, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV2),
+ XOADC_CHAN(INTERNAL, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(125V, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MUXOFF, IIO_TEMP, 1, 1, SCALE_XOTHERM, AMUX_RSV0),
+};
+
+/*
+ * Taken from arch/arm/mach-msm/board-8930-pmic.c in the vendor tree:
+ * TODO: needs testing.
+ */
+static const struct xoadc_channel pm8038_xoadc_channels[] = {
+ XOADC_CHAN(VCOIN, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(VBAT, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(DCIN, IIO_VOLTAGE, 1, 6, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(ICHG, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(VPH_PWR, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP5, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP6, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP7, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ /* MPP8 used for battery temperature in most cases */
+ XOADC_CHAN(MPP8, IIO_TEMP, 1, 1, SCALE_THERM_100K_PULLUP, AMUX_RSV2),
+ XOADC_CHAN(MPP9, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(USB_VBUS, IIO_VOLTAGE, 1, 4, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(DIE_TEMP, IIO_TEMP, 1, 1, SCALE_PMIC_THERM, AMUX_RSV1),
+ XOADC_CHAN(INTERNAL, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(125V, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(INTERNAL_2, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MUXOFF, IIO_TEMP, 1, 1, SCALE_XOTHERM, AMUX_RSV0),
+};
+
+/*
+ * This was created by cross-referencing the vendor tree
+ * arch/arm/mach-msm/board-msm8x60.c msm_adc_channels_data[]
+ * with the "channel types" (first field) to find the right
+ * configuration for these channels on an MSM8x60 i.e. PM8058
+ * setup.
+ */
+static const struct xoadc_channel pm8058_xoadc_channels[] = {
+ XOADC_CHAN(VCOIN, IIO_VOLTAGE, 1, 2, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(VBAT, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(DCIN, IIO_VOLTAGE, 1, 10, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(ICHG, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(VPH_PWR, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP5, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP6, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP7, IIO_VOLTAGE, 1, 2, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP8, IIO_VOLTAGE, 1, 2, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP9, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(USB_VBUS, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(DIE_TEMP, IIO_TEMP, 1, 1, SCALE_PMIC_THERM, AMUX_RSV1),
+ XOADC_CHAN(INTERNAL, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(125V, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(INTERNAL_2, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MUXOFF, IIO_TEMP, 1, 1, SCALE_XOTHERM, AMUX_RSV0),
+};
+
+/*
+ * The PM8921 is similar, this comes from the vendor tree
+ * board-flo-pmic.c (Nexus 7) and board-8064-pmic.c
+ * Notably the prescalers are differing.
+ */
+static const struct xoadc_channel pm8921_xoadc_channels[] = {
+ XOADC_CHAN(VCOIN, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(VBAT, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(DCIN, IIO_VOLTAGE, 1, 6, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(ICHG, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(VPH_PWR, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1),
+ /* MPP scaling is unknown, these scalings are a guess */
+ XOADC_CHAN(MPP5, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP6, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MPP7, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ /* MPP8 is usually used for battery temperature */
+ XOADC_CHAN(MPP8, IIO_TEMP, 1, 1, SCALE_THERM_100K_PULLUP, AMUX_RSV1),
+ XOADC_CHAN(MPP9, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(USB_VBUS, IIO_VOLTAGE, 1, 4, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(DIE_TEMP, IIO_TEMP, 1, 1, SCALE_PMIC_THERM, AMUX_RSV1),
+ XOADC_CHAN(INTERNAL, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(125V, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(INTERNAL_2, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
+ XOADC_CHAN(MUXOFF, IIO_TEMP, 1, 1, SCALE_XOTHERM, AMUX_RSV0),
+};
+
+/**
+ * struct pm8xxx_chan_info - ADC channel information
+ * @name: name of this channel
+ * @calibration: whether to use absolute or ratiometric calibration
+ * @scale_fn_type: scaling function type
+ * @amux_channel: channel 0..15
+ * @decimation: 0,1,2,3
+ * @amux_mpp_channel: MPP channel 0..3, selects prescaling
+ * @amux_ip_rsv: ratiometric scale value if using ratiometric
+ * calibration: 0, 1, 2, 4, 5.
+ */
+struct pm8xxx_chan_info {
+ const char *name;
+ enum vadc_calibration calibration;
+ const struct vadc_prescale_ratio *prescale;
+ enum vadc_scale_fn_type scale_fn_type;
+ u8 amux_channel:4;
+ u8 decimation:2;
+ u8 amux_mpp_channel:2;
+ u8 amux_ip_rsv:3;
+};
+
+/**
+ * struct pm8xxx_xoadc - state container for the XOADC
+ * @dev: pointer to device
+ * @map: regmap to access registers
+ * @vref: reference voltage regulator
+ * @hw_channels: the hardware channel defaults, information about the hardcoded
+ * characteristics of the channels, and sensible default settings
+ * @nchans: number of channels, configured by the device tree
+ * @chans: the channel information per-channel, configured by the device tree
+ * @iio_chans: IIO channel specifiers
+ * @graph: linear calibration parameters for absolute and
+ * ratiometric measurements
+ * @complete: completion to indicate end of conversion
+ * @lock: lock to restrict access to the hardware to one client at the time
+ * @is_pm8058: the PM8058 has some bugs that need handling
+ */
+struct pm8xxx_xoadc {
+ struct device *dev;
+ struct regmap *map;
+ struct regulator *vref;
+ const struct xoadc_channel *hw_channels;
+ unsigned int nchans;
+ struct pm8xxx_chan_info *chans;
+ struct iio_chan_spec *iio_chans;
+ struct vadc_linear_graph graph[2];
+ struct completion complete;
+ struct mutex lock;
+ bool is_pm8058;
+};
+
+static irqreturn_t pm8xxx_eoc_irq(int irq, void *d)
+{
+ struct iio_dev *indio_dev = d;
+ struct pm8xxx_xoadc *adc = iio_priv(indio_dev);
+
+ complete(&adc->complete);
+
+ return IRQ_HANDLED;
+}
+
+static struct pm8xxx_chan_info *
+pm8xxx_get_channel(struct pm8xxx_xoadc *adc, u8 chan)
+{
+ struct pm8xxx_chan_info *ch;
+ int i;
+
+ for (i = 0; i < adc->nchans; i++) {
+ ch = &adc->chans[i];
+ if (ch->amux_channel == chan)
+ break;
+ }
+ if (i == adc->nchans)
+ return NULL;
+
+ return ch;
+}
+
+static int pm8xxx_read_channel_rsv(struct pm8xxx_xoadc *adc,
+ const struct pm8xxx_chan_info *ch,
+ u8 rsv, u16 *adc_code,
+ bool force_ratiometric)
+{
+ int ret;
+ unsigned int val;
+ u8 rsvmask, rsvval;
+ u8 lsb, msb;
+
+ dev_dbg(adc->dev, "read channel \"%s\", amux %d, mpp %d, rsv %d\n",
+ ch->name, ch->amux_channel, ch->amux_mpp_channel, rsv);
+
+ mutex_lock(&adc->lock);
+
+ /* Mux in this channel */
+ ret = regmap_write(adc->map, ADC_ARB_USRP_AMUX_CNTRL,
+ ch->amux_channel << ADC_AMUX_SEL_SHIFT |
+ ch->amux_mpp_channel << ADC_AMUX_PREMUX_SHIFT);
+ if (ret)
+ goto unlock;
+
+ /* Set up ratiometric scale value, mask off all bits except these */
+ rsvmask = (ADC_ARB_USRP_RSV_RST | ADC_ARB_USRP_RSV_DTEST0 |
+ ADC_ARB_USRP_RSV_DTEST1 | ADC_ARB_USRP_RSV_OP);
+ if (adc->is_pm8058 && !force_ratiometric) {
+ /*
+ * Apparently the PM8058 has some kind of bug which is
+ * reflected in the vendor tree drivers/misc/pmix8058-xoadc.c
+ * which just hardcodes the RSV selector to SEL1 (0x20) for
+ * most cases and SEL0 (0x10) for the MUXOFF channel only.
+ * If we force ratiometric (currently only done when attempting
+ * to do ratiometric calibration) this doesn't seem to work
+ * very well and I suspect ratiometric conversion is simply
+ * broken or not supported on the PM8058.
+ *
+ * Maybe IO_SEL2 doesn't exist on PM8058 and bits 4 & 5 select
+ * the mode alone.
+ *
+ * Some PM8058 register documentation would be nice to get
+ * this right.
+ */
+ if (ch->amux_channel == PM8XXX_CHANNEL_MUXOFF)
+ rsvval = ADC_ARB_USRP_RSV_IP_SEL0;
+ else
+ rsvval = ADC_ARB_USRP_RSV_IP_SEL1;
+ } else {
+ if (rsv == 0xff)
+ rsvval = (ch->amux_ip_rsv << ADC_RSV_IP_SEL_SHIFT) |
+ ADC_ARB_USRP_RSV_TRM;
+ else
+ rsvval = (rsv << ADC_RSV_IP_SEL_SHIFT) |
+ ADC_ARB_USRP_RSV_TRM;
+ }
+
+ ret = regmap_update_bits(adc->map,
+ ADC_ARB_USRP_RSV,
+ ~rsvmask,
+ rsvval);
+ if (ret)
+ goto unlock;
+
+ ret = regmap_write(adc->map, ADC_ARB_USRP_ANA_PARAM,
+ ADC_ARB_USRP_ANA_PARAM_DIS);
+ if (ret)
+ goto unlock;
+
+ /* Decimation factor */
+ ret = regmap_write(adc->map, ADC_ARB_USRP_DIG_PARAM,
+ ADC_ARB_USRP_DIG_PARAM_SEL_SHIFT0 |
+ ADC_ARB_USRP_DIG_PARAM_SEL_SHIFT1 |
+ ch->decimation << ADC_DIG_PARAM_DEC_SHIFT);
+ if (ret)
+ goto unlock;
+
+ ret = regmap_write(adc->map, ADC_ARB_USRP_ANA_PARAM,
+ ADC_ARB_USRP_ANA_PARAM_EN);
+ if (ret)
+ goto unlock;
+
+ /* Enable the arbiter, the Qualcomm code does it twice like this */
+ ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL,
+ ADC_ARB_USRP_CNTRL_EN_ARB);
+ if (ret)
+ goto unlock;
+ ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL,
+ ADC_ARB_USRP_CNTRL_EN_ARB);
+ if (ret)
+ goto unlock;
+
+
+ /* Fire a request! */
+ reinit_completion(&adc->complete);
+ ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL,
+ ADC_ARB_USRP_CNTRL_EN_ARB |
+ ADC_ARB_USRP_CNTRL_REQ);
+ if (ret)
+ goto unlock;
+
+ /* Next the interrupt occurs */
+ ret = wait_for_completion_timeout(&adc->complete,
+ VADC_CONV_TIME_MAX_US);
+ if (!ret) {
+ dev_err(adc->dev, "conversion timed out\n");
+ ret = -ETIMEDOUT;
+ goto unlock;
+ }
+
+ ret = regmap_read(adc->map, ADC_ARB_USRP_DATA0, &val);
+ if (ret)
+ goto unlock;
+ lsb = val;
+ ret = regmap_read(adc->map, ADC_ARB_USRP_DATA1, &val);
+ if (ret)
+ goto unlock;
+ msb = val;
+ *adc_code = (msb << 8) | lsb;
+
+ /* Turn off the ADC by setting the arbiter to 0 twice */
+ ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL, 0);
+ if (ret)
+ goto unlock;
+ ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL, 0);
+ if (ret)
+ goto unlock;
+
+unlock:
+ mutex_unlock(&adc->lock);
+ return ret;
+}
+
+static int pm8xxx_read_channel(struct pm8xxx_xoadc *adc,
+ const struct pm8xxx_chan_info *ch,
+ u16 *adc_code)
+{
+ /*
+ * Normally we just use the ratiometric scale value (RSV) predefined
+ * for the channel, but during calibration we need to modify this
+ * so this wrapper is a helper hiding the more complex version.
+ */
+ return pm8xxx_read_channel_rsv(adc, ch, 0xff, adc_code, false);
+}
+
+static int pm8xxx_calibrate_device(struct pm8xxx_xoadc *adc)
+{
+ const struct pm8xxx_chan_info *ch;
+ u16 read_1250v;
+ u16 read_0625v;
+ u16 read_nomux_rsv5;
+ u16 read_nomux_rsv4;
+ int ret;
+
+ adc->graph[VADC_CALIB_ABSOLUTE].dx = VADC_ABSOLUTE_RANGE_UV;
+ adc->graph[VADC_CALIB_RATIOMETRIC].dx = VADC_RATIOMETRIC_RANGE;
+
+ /* Common reference channel calibration */
+ ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_125V);
+ if (!ch)
+ return -ENODEV;
+ ret = pm8xxx_read_channel(adc, ch, &read_1250v);
+ if (ret) {
+ dev_err(adc->dev, "could not read 1.25V reference channel\n");
+ return -ENODEV;
+ }
+ ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_INTERNAL);
+ if (!ch)
+ return -ENODEV;
+ ret = pm8xxx_read_channel(adc, ch, &read_0625v);
+ if (ret) {
+ dev_err(adc->dev, "could not read 0.625V reference channel\n");
+ return -ENODEV;
+ }
+ if (read_1250v == read_0625v) {
+ dev_err(adc->dev, "read same ADC code for 1.25V and 0.625V\n");
+ return -ENODEV;
+ }
+
+ adc->graph[VADC_CALIB_ABSOLUTE].dy = read_1250v - read_0625v;
+ adc->graph[VADC_CALIB_ABSOLUTE].gnd = read_0625v;
+
+ dev_info(adc->dev, "absolute calibration dx = %d uV, dy = %d units\n",
+ VADC_ABSOLUTE_RANGE_UV, adc->graph[VADC_CALIB_ABSOLUTE].dy);
+
+ /* Ratiometric calibration */
+ ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_MUXOFF);
+ if (!ch)
+ return -ENODEV;
+ ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV5,
+ &read_nomux_rsv5, true);
+ if (ret) {
+ dev_err(adc->dev, "could not read MUXOFF reference channel\n");
+ return -ENODEV;
+ }
+ ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV4,
+ &read_nomux_rsv4, true);
+ if (ret) {
+ dev_err(adc->dev, "could not read MUXOFF reference channel\n");
+ return -ENODEV;
+ }
+ adc->graph[VADC_CALIB_RATIOMETRIC].dy =
+ read_nomux_rsv5 - read_nomux_rsv4;
+ adc->graph[VADC_CALIB_RATIOMETRIC].gnd = read_nomux_rsv4;
+
+ dev_info(adc->dev, "ratiometric calibration dx = %d, dy = %d units\n",
+ VADC_RATIOMETRIC_RANGE,
+ adc->graph[VADC_CALIB_RATIOMETRIC].dy);
+
+ return 0;
+}
+
+static int pm8xxx_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ struct pm8xxx_xoadc *adc = iio_priv(indio_dev);
+ const struct pm8xxx_chan_info *ch;
+ u16 adc_code;
+ int ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_PROCESSED:
+ ch = pm8xxx_get_channel(adc, chan->address);
+ if (!ch) {
+ dev_err(adc->dev, "no such channel %lu\n",
+ chan->address);
+ return -EINVAL;
+ }
+ ret = pm8xxx_read_channel(adc, ch, &adc_code);
+ if (ret)
+ return ret;
+
+ ret = qcom_vadc_scale(ch->scale_fn_type,
+ &adc->graph[ch->calibration],
+ ch->prescale,
+ (ch->calibration == VADC_CALIB_ABSOLUTE),
+ adc_code, val);
+ if (ret)
+ return ret;
+
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_RAW:
+ ch = pm8xxx_get_channel(adc, chan->address);
+ if (!ch) {
+ dev_err(adc->dev, "no such channel %lu\n",
+ chan->address);
+ return -EINVAL;
+ }
+ ret = pm8xxx_read_channel(adc, ch, &adc_code);
+ if (ret)
+ return ret;
+
+ *val = (int)adc_code;
+ return IIO_VAL_INT;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int pm8xxx_of_xlate(struct iio_dev *indio_dev,
+ const struct of_phandle_args *iiospec)
+{
+ struct pm8xxx_xoadc *adc = iio_priv(indio_dev);
+ unsigned int i;
+
+ for (i = 0; i < adc->nchans; i++)
+ if (adc->iio_chans[i].channel == iiospec->args[0])
+ return i;
+
+ return -EINVAL;
+}
+
+static const struct iio_info pm8xxx_xoadc_info = {
+ .driver_module = THIS_MODULE,
+ .of_xlate = pm8xxx_of_xlate,
+ .read_raw = pm8xxx_read_raw,
+};
+
+static int pm8xxx_xoadc_parse_channel(struct device *dev,
+ struct device_node *np,
+ const struct xoadc_channel *hw_channels,
+ struct iio_chan_spec *iio_chan,
+ struct pm8xxx_chan_info *ch)
+{
+ const char *name = np->name;
+ u32 chan, rsv, dec;
+ int ret;
+
+ ret = of_property_read_u32(np, "reg", &chan);
+ if (ret) {
+ dev_err(dev, "invalid channel number %s\n", name);
+ return ret;
+ }
+ if (chan >= XOADC_CHANNELS) {
+ dev_err(dev, "%s too big channel number %d\n", name, chan);
+ return -EINVAL;
+ }
+
+ /* Look up default channel settings */
+ ch->amux_channel = chan;
+ ch->name = name;
+ ch->prescale = &hw_channels[chan].prescale;
+ ch->scale_fn_type = hw_channels[chan].scale_fn_type;
+ ch->amux_ip_rsv = hw_channels[chan].amux_ip_rsv;
+ /* Everyone seems to use absolute calibration except in special cases */
+ ch->calibration = VADC_CALIB_ABSOLUTE;
+ /* Everyone seems to use default ("type 2") decimation */
+ ch->decimation = VADC_DEF_DECIMATION;
+ /* Everyone seems to use this 1-to-1 premux scaling channel */
+ ch->amux_mpp_channel = MPP_SCALE_0;
+
+ if (!of_property_read_u32(np, "qcom,ratiometric", &rsv)) {
+ ch->calibration = VADC_CALIB_RATIOMETRIC;
+ if (rsv > XOADC_RSV_MAX) {
+ dev_err(dev, "%s too large RSV value %d\n", name, rsv);
+ return -EINVAL;
+ }
+ if (rsv == AMUX_RSV3) {
+ dev_err(dev, "%s invalid RSV value %d\n", name, rsv);
+ return -EINVAL;
+ }
+ }
+
+ /* Optional decimation, if omitted we use the default */
+ ret = of_property_read_u32(np, "qcom,decimation", &dec);
+ if (!ret) {
+ ret = qcom_vadc_decimation_from_dt(dec);
+ if (ret < 0) {
+ dev_err(dev, "%s invalid decimation %d\n",
+ name, dec);
+ return ret;
+ }
+ ch->decimation = ret;
+ }
+
+ iio_chan->channel = ch->amux_channel;
+ iio_chan->address = ch->amux_channel;
+ iio_chan->datasheet_name = ch->name;
+ iio_chan->type = hw_channels[chan].type;
+ /* All channels are raw or processed */
+ iio_chan->info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_PROCESSED);
+ iio_chan->indexed = 1;
+
+ dev_dbg(dev, "channel %d \"%s\" ref voltage: %d, decimation %d "
+ "prescale %d/%d, scale function %d\n",
+ ch->amux_channel, ch->name, ch->amux_ip_rsv,
+ ch->decimation, ch->prescale->num, ch->prescale->den,
+ ch->scale_fn_type);
+
+ return 0;
+}
+
+static int pm8xxx_xoadc_parse_channels(struct pm8xxx_xoadc *adc,
+ struct device_node *np)
+{
+ struct device_node *child;
+ struct pm8xxx_chan_info *ch;
+ int ret;
+ int i;
+
+ adc->nchans = of_get_available_child_count(np);
+ if (!adc->nchans) {
+ dev_err(adc->dev, "no channel children\n");
+ return -ENODEV;
+ }
+ dev_dbg(adc->dev, "found %d ADC channels\n", adc->nchans);
+
+ adc->iio_chans = devm_kcalloc(adc->dev, adc->nchans,
+ sizeof(*adc->iio_chans), GFP_KERNEL);
+ if (!adc->iio_chans)
+ return -ENOMEM;
+
+ adc->chans = devm_kcalloc(adc->dev, adc->nchans,
+ sizeof(*adc->chans), GFP_KERNEL);
+ if (!adc->chans)
+ return -ENOMEM;
+
+ i = 0;
+ for_each_available_child_of_node(np, child) {
+ ch = &adc->chans[i];
+ ret = pm8xxx_xoadc_parse_channel(adc->dev, child,
+ adc->hw_channels,
+ &adc->iio_chans[i],
+ ch);
+ if (ret) {
+ of_node_put(child);
+ return ret;
+ }
+ i++;
+ }
+
+ /* Check for required channels */
+ ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_125V);
+ if (!ch) {
+ dev_err(adc->dev, "missing 1.25V reference channel\n");
+ return -ENODEV;
+ }
+ ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_INTERNAL);
+ if (!ch) {
+ dev_err(adc->dev, "missing 0.625V reference channel\n");
+ return -ENODEV;
+ }
+ ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_MUXOFF);
+ if (!ch) {
+ dev_err(adc->dev, "missing MUXOFF reference channel\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int pm8xxx_xoadc_probe(struct platform_device *pdev)
+{
+ struct pm8xxx_xoadc *adc;
+ struct iio_dev *indio_dev;
+ struct device_node *np = pdev->dev.of_node;
+ struct regmap *map;
+ struct device *dev = &pdev->dev;
+ const char *compat;
+ int ret;
+
+ /* We need this compatible string */
+ if (of_property_read_string(np, "compatible", &compat))
+ return -ENODEV;
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
+ if (!indio_dev)
+ return -ENOMEM;
+ platform_set_drvdata(pdev, indio_dev);
+
+ adc = iio_priv(indio_dev);
+ adc->dev = dev;
+ init_completion(&adc->complete);
+ mutex_init(&adc->lock);
+
+ /* Look up variant data */
+ adc->hw_channels = of_device_get_match_data(dev);
+ if (!adc->hw_channels) {
+ dev_err(dev, "missing variant data\n");
+ return -ENODEV;
+ }
+
+ /* This variant has special bugs that we need to deal with */
+ if (of_device_is_compatible(np, "qcom,pm8058-adc"))
+ adc->is_pm8058 = true;
+
+ ret = pm8xxx_xoadc_parse_channels(adc, np);
+ if (ret)
+ return ret;
+
+ map = dev_get_regmap(dev->parent, NULL);
+ if (!map) {
+ dev_err(dev, "parent regmap unavailable.\n");
+ return -ENXIO;
+ }
+ adc->map = map;
+
+ /* Bring up regulator */
+ adc->vref = devm_regulator_get(dev, "xoadc-ref");
+ if (IS_ERR(adc->vref)) {
+ dev_err(dev, "failed to get XOADC VREF regulator\n");
+ return PTR_ERR(adc->vref);
+ }
+ ret = regulator_enable(adc->vref);
+ if (ret) {
+ dev_err(dev, "failed to enable XOADC VREF regulator\n");
+ return ret;
+ }
+
+ ret = devm_request_threaded_irq(dev, platform_get_irq(pdev, 0),
+ pm8xxx_eoc_irq, NULL, 0, "pm8xxx-adc", indio_dev);
+ if (ret) {
+ dev_err(dev, "unable to request IRQ\n");
+ goto out_disable_vref;
+ }
+
+ indio_dev->dev.parent = dev;
+ indio_dev->dev.of_node = np;
+ indio_dev->name = compat;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->info = &pm8xxx_xoadc_info;
+ indio_dev->channels = adc->iio_chans;
+ indio_dev->num_channels = adc->nchans;
+
+ ret = iio_device_register(indio_dev);
+ if (ret)
+ goto out_disable_vref;
+
+ ret = pm8xxx_calibrate_device(adc);
+ if (ret)
+ goto out_unreg_device;
+
+ dev_info(dev, "PM8xxx XOADC driver enabled\n");
+
+ return 0;
+
+out_unreg_device:
+ iio_device_unregister(indio_dev);
+out_disable_vref:
+ regulator_disable(adc->vref);
+
+ return ret;
+}
+
+static int pm8xxx_xoadc_remove(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+ struct pm8xxx_xoadc *adc = iio_priv(indio_dev);
+
+ iio_device_unregister(indio_dev);
+
+ regulator_disable(adc->vref);
+
+ return 0;
+}
+
+static const struct of_device_id pm8xxx_xoadc_id_table[] = {
+ {
+ .compatible = "qcom,pm8018-adc",
+ .data = &pm8018_xoadc_channels,
+ },
+ {
+ .compatible = "qcom,pm8038-adc",
+ .data = &pm8038_xoadc_channels,
+ },
+ {
+ .compatible = "qcom,pm8058-adc",
+ .data = &pm8058_xoadc_channels,
+ },
+ {
+ .compatible = "qcom,pm8921-adc",
+ .data = &pm8921_xoadc_channels,
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(of, pm8xxx_xoadc_id_table);
+
+static struct platform_driver pm8xxx_xoadc_driver = {
+ .driver = {
+ .name = "pm8xxx-adc",
+ .of_match_table = pm8xxx_xoadc_id_table,
+ },
+ .probe = pm8xxx_xoadc_probe,
+ .remove = pm8xxx_xoadc_remove,
+};
+module_platform_driver(pm8xxx_xoadc_driver);
+
+MODULE_DESCRIPTION("PM8xxx XOADC driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:pm8xxx-xoadc");
--
2.9.3
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
