Qualcomm chipsets have QMP phy controller that provides
support to a number of controller, viz. PCIe, UFS, and USB.
Adding dt binding information for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@xxxxxxxxxxxxxx>
Acked-by: Rob Herring <robh@xxxxxxxxxx>
---
Changes since v3:
- Added #clock-cells = <1>, indicating that phy is a clock provider.
Changes since v2:
- Removed binding for "ref_clk_src" since we don't request this
clock in the driver.
- Addressed s/ref_clk/ref. Don't need to add '_clk' suffix to clock names.
- Using 'phy' for the node name.
Changes since v1:
- New patch, forked out of the original driver patch:
"phy: qcom-qmp: new qmp phy driver for qcom-chipsets"
- Added 'Acked-by' from Rob.
- Updated bindings to include mem resource as a list of
offset - length pair for serdes block and for each lane.
- Added a new binding for 'lane-offsets' that contains offsets
to tx, rx and pcs blocks from each lane base address.
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 76 ++++++++++++++++++++++
1 file changed, 76 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
new file mode 100644
index 000000000000..6f510fe48f46
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
@@ -0,0 +1,76 @@
+Qualcomm QMP PHY controller
+===========================
+
+QMP phy controller supports physical layer functionality for a number of
+controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
+
+Required properties:
+ - compatible: compatible list, contains:
+ "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
+ "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996.
+ - reg: list of offset and length pair of the PHY register sets.
+ at index 0: offset and length of register set for PHY common
+ serdes block.
+ from index 1 - N: offset and length of register set for each lane,
+ for N number of phy lanes (ports).
+ - lane-offsets: array of offsets to tx, rx and pcs blocks for phy lanes.
+ - #phy-cells: must be 1
+ - Cell after phy phandle should be the port (lane) number.
+ - #clock-cells: must be 1
+ - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
+ interface (for pipe based PHYs). These clock are then gate-controlled
+ by gcc.
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: must be "cfg_ahb" for phy config clock,
+ "aux" for phy aux clock,
+ "ref" for 19.2 MHz ref clk,
+ "pipe<port-number>" for pipe clock specific to
+ each port/lane (Optional).
+ - resets: a list of phandles and reset controller specifier pairs,
+ one for each entry in reset-names.
+ - reset-names: must be "phy" for reset of phy block,
+ "common" for phy common block reset,
+ "cfg" for phy's ahb cfg block reset (Optional).
+ "port<port-number>" for reset specific to
+ each port/lane (Optional).
+ - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+Optional properties:
+ - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
+ pll block.
+
+Example:
+ pcie_phy: phy@34000 {
+ compatible = "qcom,msm8996-qmp-pcie-phy";
+ reg = <0x034000 0x48f>,
+ <0x035000 0x5bf>,
+ <0x036000 0x5bf>,
+ <0x037000 0x5bf>;
+ /* tx, rx, pcs */
+ lane-offsets = <0x0 0x200 0x400>;
+ #phy-cells = <1>;
+ #clock-cells = <1>;
+
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_CLKREF_CLK>,
+ <&gcc GCC_PCIE_0_PIPE_CLK>,
+ <&gcc GCC_PCIE_1_PIPE_CLK>,
+ <&gcc GCC_PCIE_2_PIPE_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref",
+ "pipe0", "pipe1", "pipe2";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+
+ resets = <&gcc GCC_PCIE_PHY_BCR>,
+ <&gcc GCC_PCIE_PHY_COM_BCR>,
+ <&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>,
+ <&gcc GCC_PCIE_0_PHY_BCR>,
+ <&gcc GCC_PCIE_1_PHY_BCR>,
+ <&gcc GCC_PCIE_2_PHY_BCR>;
+ reset-names = "phy", "common", "cfg",
+ "lane0", "lane1", "lane2";
