Add Nexus 5X (msm8992) SDHCI support, including initial regulator
entries to support enabling the main SDHCI/MMC.
The msm8994 RPM regulator talks over SMD to the APPS processor.
Signed-off-by: Jeremy McNicoll <jeremymc@xxxxxxxxxx>
---
.../bindings/regulator/qcom,smd-rpm-regulator.txt | 40 ++++
.../boot/dts/qcom/msm8992-bullhead-rev-101.dts | 262 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/msm8992-pins.dtsi | 82 +++++++
arch/arm64/boot/dts/qcom/msm8992.dtsi | 153 ++++++++++++
drivers/regulator/qcom_smd-regulator.c | 49 ++++
5 files changed, 586 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt
index 1f8d6f8..126989b 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt
@@ -23,6 +23,7 @@ Regulator nodes are identified by their compatible:
"qcom,rpm-pm8916-regulators"
"qcom,rpm-pm8941-regulators"
"qcom,rpm-pma8084-regulators"
+ "qcom,rpm-pm8994-regulators"
- vdd_s1-supply:
- vdd_s2-supply:
@@ -97,6 +98,40 @@ Regulator nodes are identified by their compatible:
Definition: reference to regulator supplying the input pin, as
described in the data sheet
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_s6-supply:
+- vdd_s7-supply:
+- vdd_l1_l11-supply:
+- vdd_l2_l3_l4_l27-supply:
+- vdd_l5_l7-supply:
+- vdd_l6_l12_l14_l15_l26-supply:
+- vdd_l8-supply:
+- vdd_l9_l10_l13_l20_l23_l24-supply:
+- vdd_l1_l11-supply:
+- vdd_l6_l12_l14_l15_l26-supply:
+- vdd_l16_l25-supply:
+- vdd_l17-supply:
+- vdd_l18-supply:
+- vdd_l19-supply:
+- vdd_l21-supply:
+- vdd_l22-supply:
+- vdd_l16_l25-supply:
+- vdd_l27-supply:
+- vdd_l28-supply:
+- vdd_l29-supply:
+- vdd_l30-supply:
+- vdd_l31-supply:
+- vdd_l32-supply:
+ Usage: optional (pm8994 only)
+ Value type: <phandle>
+ Definition: reference to regulator supplying the input pin, as
+ described in the data sheet.
+
+
The regulator node houses sub-nodes for each regulator within the device. Each
sub-node is identified using the node's name, with valid values listed for each
of the pmics below.
@@ -118,6 +153,11 @@ pma8084:
l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20,
l21, l22, l23, l24, l25, l26, l27, lvs1, lvs2, lvs3, lvs4, 5vs1
+pm8994:
+ s1, s2, s3, s4, s5, s6, s7, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
+ l12, l13, l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, l26,
+ l27, l28, l29, l30, l31, l32, lvs1, lvs2
+
The content of each sub-node is defined by the standard binding for regulators -
see regulator.txt.
diff --git a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
index 4542133..2ce8798 100644
--- a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
+++ b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
@@ -39,3 +39,265 @@
};
};
};
+
+&smd_rpm {
+ rpm {
+ rpm_requests {
+ pm8994-regulators {
+
+ vdd_l1-supply = <&pm8994_s1>;
+ vdd_l2_26_28-supply = <&pm8994_s3>;
+ vdd_l3_11-supply = <&pm8994_s3>;
+ vdd_l4_27_31-supply = <&pm8994_s3>;
+ vdd_l5_7-supply = <&pm8994_s3>;
+ vdd_l6_12_32-supply = <&pm8994_s5>;
+ vdd_l8_16_30-supply = <&vreg_vph_pwr>;
+ vdd_l9_10_18_22-supply = <&vreg_vph_pwr>;
+ vdd_l13_19_23_24-supply = <&vreg_vph_pwr>;
+ vdd_l14_15-supply = <&pm8994_s5>;
+ vdd_l17_29-supply = <&vreg_vph_pwr>;
+ vdd_l20_21-supply = <&vreg_vph_pwr>;
+ vdd_l25-supply = <&pm8994_s5>;
+ /*vin_lvs1_2 = <&pm8994_s4>; */
+
+ s1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ s2 {
+ };
+
+ s3 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allow-set-load;
+ regulator-system-load = <325000>;
+ };
+
+ s5 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ };
+
+ s7 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l5 {
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l7 {
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,init-voltage = <1800000>;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ qcom,init-voltage = <1200000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,init-voltage = <1800000>;
+ proxy-supply = <&pm8994_l12>;
+ qcom,proxy-consumer-enable;
+ qcom,proxy-consumer-current = <10000>;
+ status = "okay";
+ };
+
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ qcom,init-voltage = <2950000>;
+ status = "okay";
+ };
+
+ l14 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ qcom,init-voltage = <1200000>;
+ proxy-supply = <&pm8994_l14>;
+ qcom,proxy-consumer-enable;
+ qcom,proxy-consumer-current = <10000>;
+ status = "okay";
+ };
+
+ l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,init-voltage = <1800000>;
+ status = "okay";
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ qcom,init-voltage = <2700000>;
+ status = "okay";
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ qcom,init-voltage = <2700000>;
+ status = "okay";
+ };
+
+ l18 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ qcom,init-voltage = <3000000>;
+ qcom,init-ldo-mode = <1>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,init-voltage = <1800000>;
+ status = "okay";
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ regulator-system-load = <570000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ qcom,init-voltage = <1800000>;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3100000>;
+ regulator-max-microvolt = <3100000>;
+ qcom,init-voltage = <3100000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ qcom,init-voltage = <2800000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3150000>;
+ qcom,init-voltage = <3075000>;
+ };
+
+ l25 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,init-voltage = <1800000>;
+ };
+
+ l26 {
+ /* TODO: value from downstream
+ regulator-min-microvolt = <987500>;
+ fails to apply */
+ };
+
+ l27 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ qcom,init-voltage = <1050000>;
+ };
+
+ l28 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ qcom,init-voltage = <1000000>;
+ proxy-supply = <&pm8994_l28>;
+ qcom,proxy-consumer-enable;
+ qcom,proxy-consumer-current = <10000>;
+ };
+
+ l29 {
+ /* TODO: Unsupported voltage range..
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ qcom,init-voltage = <2800000>;
+ */
+ };
+
+ l30 {
+ /* TODO: get this verified
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,init-voltage = <1800000>;
+ */
+ };
+
+ l31 {
+ regulator-min-microvolt = <1262500>;
+ regulator-max-microvolt = <1262500>;
+ qcom,init-voltage = <1262500>;
+ };
+
+ l32 {
+ /* TODO: get this verified
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,init-voltage = <1800000>;
+ */
+ };
+
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8992-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8992-pins.dtsi
index d2a26f0..15202c8 100644
--- a/arch/arm64/boot/dts/qcom/msm8992-pins.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992-pins.dtsi
@@ -35,4 +35,86 @@
bias-pull-down;
};
};
+
+ /* 0-3 for sdc1 4-6 for sdc2 */
+ /* Order of pins */
+ /* SDC1: CLK -> 0, CMD -> 1, DATA -> 2, RCLK -> 3 */
+ /* SDC2: CLK -> 4, CMD -> 5, DATA -> 6 */
+ pmx_sdc1_clk {
+ sdc1_clk_on: clk_on {
+ pinmux {
+ pins = "sdc1_clk";
+ };
+ pinconf {
+ pins = "sdc1_clk";
+ bias-disable = <0>; /* No pull */
+ drive-strength = <16>; /* 16mA */
+ };
+ };
+ sdc1_clk_off: clk_off {
+ pinmux {
+ pins = "sdc1_clk";
+ };
+ pinconf {
+ pins = "sdc1_clk";
+ bias-disable = <0>; /* No pull */
+ drive-strength = <2>; /* 2mA */
+ };
+ };
+ };
+
+ pmx_sdc1_cmd {
+ sdc1_cmd_on: cmd_on {
+ pinmux {
+ pins = "sdc1_cmd";
+ };
+ pinconf {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+ };
+ sdc1_cmd_off: cmd_off {
+ pinmux {
+ pins = "sdc1_cmd";
+ };
+ pinconf {
+ pins = "sdc1_cmd";
+ bias-pull-up = <0x3>; /* same as 3.10 ?? */
+ drive-strength = <2>; /* 2mA */
+ };
+ };
+ };
+
+ pmx_sdc1_data {
+ sdc1_data_on: data_on {
+ pinmux {
+ pins = "sdc1_data";
+ };
+ pinconf {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <8>; /* 8mA */
+ };
+ };
+ sdc1_data_off: data_off {
+ pinmux {
+ pins = "sdc1_data";
+ };
+ pinconf {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };
+ };
+
+ pmx_sdc1_rclk {
+ sdc1_rclk_on: rclk_on {
+ bias-pull-down; /* pull down */
+ };
+ sdc1_rclk_off: rclk_off {
+ bias-pull-down; /* pull down */
+ };
+ };
};
diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi
index 44b2d37..d104770 100644
--- a/arch/arm64/boot/dts/qcom/msm8992.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi
@@ -82,6 +82,12 @@
<0xf9002000 0x1000>;
};
+ apcs: syscon@0xf900d000 {
+ compatible = "syscon";
+ reg = <0xf900d000 0x2000>;
+ };
+
+
timer@f9020000 {
#address-cells = <1>;
#size-cells = <1>;
@@ -172,12 +178,159 @@
#power-domain-cells = <1>;
reg = <0xfc400000 0x2000>;
};
+
+ sdhci1: qcom,sdhci@f9824900 {
+ compatible = "qcom,sdhci-msm-v4";
+ reg = <0xf9824900 0x1a0>, <0xf9824000 0x800>;
+ reg-names = "hc_mem", "core_mem";
+
+ interrupts = <GIC_SPI 123 IRQ_TYPE_NONE>,
+ <GIC_SPI 138 IRQ_TYPE_NONE>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&clock_gcc GCC_SDCC1_APPS_CLK>,
+ <&clock_gcc GCC_SDCC1_AHB_CLK>;
+ clock-names = "core", "iface";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on
+ &sdc1_rclk_on>;
+ pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off
+ &sdc1_rclk_off>;
+
+ vdd-supply = <&pm8994_l20>;
+ qcom,vdd-voltage-level = <2950000 2950000>;
+ qcom,vdd-current-level = <200 570000>;
+
+ vdd-io-supply = <&pm8994_s4>;
+ qcom,vdd-io-voltage-level = <1800000 1800000>;
+ qcom,vdd-io-current-level = <200 325000>;
+
+ regulator-always-on;
+ bus-width = <8>;
+ mmc-hs400-1_8v;
+ status = "okay";
+ };
+
+ vreg_vph_pwr: vreg-vph-pwr {
+ compatible = "regulator-fixed";
+ status = "okay";
+ regulator-name = "vph-pwr";
+
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+
+ regulator-always-on;
+ };
+
+ rpm_msg_ram: memory@fc428000 {
+ compatible = "qcom,rpm-msg-ram";
+ reg = <0xfc428000 0x4000>;
+ };
+
+ sfpb_mutex_regs: syscon@fd484000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "syscon";
+ reg = <0xfd484000 0x400>;
+ };
+
+ sfpb_mutex: hwmutex {
+ compatible = "qcom,sfpb-mutex";
+ syscon = <&sfpb_mutex_regs 0x0 0x100>;
+ #hwlock-cells = <1>;
+ };
+
+ smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem_region>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ hwlocks = <&sfpb_mutex 3>;
+ };
};
memory {
device_type = "memory";
reg = <0 0 0 0>; // bootloader will update
};
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ smem_region: smem@6a00000 {
+ reg = <0x0 0x6a00000 0x0 0x200000>;
+ no-map;
+ };
+ };
+
+ smd_rpm: smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+ qcom,ipc = <&apcs 8 0>;
+ qcom,smd-edge = <15>;
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <6>;
+
+ rpm_requests {
+ compatible = "qcom,rpm-msm8994";
+ qcom,smd-channels = "rpm_requests";
+
+ rpmcc: qcom,rpmcc {
+ /* TODO: update when rpmcc-msm8994 support added */
+ compatible = "qcom,rpmcc-msm8916",
+ "qcom,rpmcc";
+ #clock-cells = <1>;
+ };
+
+ smd_rpm_regulators: pm8994-regulators {
+ compatible = "qcom,rpm-pm8994-regulators";
+
+ pm8994_s1: s1 {};
+ pm8994_s2: s2 {};
+ pm8994_s3: s3 {};
+ pm8994_s4: s4 {};
+ pm8994_s5: s5 {};
+ pm8994_s6: s6 {};
+ pm8994_s7: s7 {};
+
+ pm8994_l1: l1 {};
+ pm8994_l2: l2 {};
+ pm8994_l3: l3 {};
+ pm8994_l4: l4 {};
+ pm8994_l6: l6 {};
+ pm8994_l8: l8 {};
+ pm8994_l9: l9 {};
+ pm8994_l10: l10 {};
+ pm8994_l11: l11 {};
+ pm8994_l12: l12 {};
+ pm8994_l13: l13 {};
+ pm8994_l14: l14 {};
+ pm8994_l15: l15 {};
+ pm8994_l16: l16 {};
+ pm8994_l17: l17 {};
+ pm8994_l18: l18 {};
+ pm8994_l19: l19 {};
+ pm8994_l20: l20 {};
+ pm8994_l21: l21 {};
+ pm8994_l22: l22 {};
+ pm8994_l23: l23 {};
+ pm8994_l24: l24 {};
+ pm8994_l25: l25 {};
+ pm8994_l26: l26 {};
+ pm8994_l27: l27 {};
+ pm8994_l28: l28 {};
+ pm8994_l29: l29 {};
+ pm8994_l30: l30 {};
+ pm8994_l31: l31 {};
+ pm8994_l32: l32 {};
+ };
+ };
+ };
+ };
};
diff --git a/drivers/regulator/qcom_smd-regulator.c b/drivers/regulator/qcom_smd-regulator.c
index 8ed46a9..a7e8ce7 100644
--- a/drivers/regulator/qcom_smd-regulator.c
+++ b/drivers/regulator/qcom_smd-regulator.c
@@ -443,11 +443,60 @@ static const struct rpm_regulator_data rpm_pma8084_regulators[] = {
{}
};
+static const struct rpm_regulator_data rpm_pm8994_regulators[] = {
+ { "s1", QCOM_SMD_RPM_SMPA, 1, &pma8084_ftsmps, "vdd_s1" },
+ { "s2", QCOM_SMD_RPM_SMPA, 2, &pma8084_ftsmps, "vdd_s2" },
+ { "s3", QCOM_SMD_RPM_SMPA, 3, &pma8084_hfsmps, "vdd_s3" },
+ { "s4", QCOM_SMD_RPM_SMPA, 4, &pma8084_hfsmps, "vdd_s4" },
+ { "s5", QCOM_SMD_RPM_SMPA, 5, &pma8084_hfsmps, "vdd_s5" },
+ { "s6", QCOM_SMD_RPM_SMPA, 6, &pma8084_ftsmps, "vdd_s6" },
+ { "s7", QCOM_SMD_RPM_SMPA, 7, &pma8084_ftsmps, "vdd_s7" },
+
+ { "l1", QCOM_SMD_RPM_LDOA, 1, &pma8084_nldo, "vdd_l1_l11" },
+ { "l2", QCOM_SMD_RPM_LDOA, 2, &pma8084_nldo, "vdd_l2_l3_l4_l27" },
+ { "l3", QCOM_SMD_RPM_LDOA, 3, &pma8084_nldo, "vdd_l2_l3_l4_l27" },
+ { "l4", QCOM_SMD_RPM_LDOA, 4, &pma8084_nldo, "vdd_l2_l3_l4_l27" },
+ { "l5", QCOM_SMD_RPM_LDOA, 5, &pma8084_pldo, "vdd_l5_l7" },
+ { "l6", QCOM_SMD_RPM_LDOA, 6, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+ { "l7", QCOM_SMD_RPM_LDOA, 7, &pma8084_pldo, "vdd_l5_l7" },
+ { "l8", QCOM_SMD_RPM_LDOA, 8, &pma8084_pldo, "vdd_l8" },
+ { "l9", QCOM_SMD_RPM_LDOA, 9, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+ { "l10", QCOM_SMD_RPM_LDOA, 10, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+ { "l11", QCOM_SMD_RPM_LDOA, 11, &pma8084_nldo, "vdd_l1_l11" },
+ { "l12", QCOM_SMD_RPM_LDOA, 12, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+ { "l13", QCOM_SMD_RPM_LDOA, 13, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+ { "l14", QCOM_SMD_RPM_LDOA, 14, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+ { "l15", QCOM_SMD_RPM_LDOA, 15, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+ { "l16", QCOM_SMD_RPM_LDOA, 16, &pma8084_pldo, "vdd_l16_l25" },
+ { "l17", QCOM_SMD_RPM_LDOA, 17, &pma8084_pldo, "vdd_l17" },
+ { "l18", QCOM_SMD_RPM_LDOA, 18, &pma8084_pldo, "vdd_l18" },
+ { "l19", QCOM_SMD_RPM_LDOA, 19, &pma8084_pldo, "vdd_l19" },
+ { "l20", QCOM_SMD_RPM_LDOA, 20, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+ { "l21", QCOM_SMD_RPM_LDOA, 21, &pma8084_pldo, "vdd_l21" },
+ { "l22", QCOM_SMD_RPM_LDOA, 22, &pma8084_pldo, "vdd_l22" },
+ { "l23", QCOM_SMD_RPM_LDOA, 23, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+ { "l24", QCOM_SMD_RPM_LDOA, 24, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+ { "l25", QCOM_SMD_RPM_LDOA, 25, &pma8084_pldo, "vdd_l16_l25" },
+ { "l26", QCOM_SMD_RPM_LDOA, 26, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+ { "l27", QCOM_SMD_RPM_LDOA, 27, &pma8084_nldo, "vdd_l27" },
+ { "l28", QCOM_SMD_RPM_LDOA, 28, &pma8084_nldo, "vdd_l28" },
+ { "l29", QCOM_SMD_RPM_LDOA, 29, &pma8084_nldo, "vdd_l29" },
+ { "l30", QCOM_SMD_RPM_LDOA, 30, &pma8084_nldo, "vdd_l30" },
+ { "l31", QCOM_SMD_RPM_LDOA, 31, &pma8084_nldo, "vdd_l31" },
+ { "l32", QCOM_SMD_RPM_LDOA, 32, &pma8084_nldo, "vdd_l32" },
+
+ { "lvs1", QCOM_SMD_RPM_VSA, 1, &pma8084_switch },
+ { "lvs2", QCOM_SMD_RPM_VSA, 2, &pma8084_switch },
+
+ {}
+};
+
static const struct of_device_id rpm_of_match[] = {
{ .compatible = "qcom,rpm-pm8841-regulators", .data = &rpm_pm8841_regulators },
{ .compatible = "qcom,rpm-pm8916-regulators", .data = &rpm_pm8916_regulators },
{ .compatible = "qcom,rpm-pm8941-regulators", .data = &rpm_pm8941_regulators },
{ .compatible = "qcom,rpm-pma8084-regulators", .data = &rpm_pma8084_regulators },
+ { .compatible = "qcom,rpm-pm8994-regulators", .data = &rpm_pm8994_regulators },
{}
};
MODULE_DEVICE_TABLE(of, rpm_of_match);
--
2.6.1
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
