Hi, This is v9 version of the patch series which adds support for MSM8996. Adds HS400 driver support as well. These are tested on internal msm8996 & db410c HW. The patch series is ready. Do we think we can apply these patches for next now? There are only minor changes in v9. 1. From <&xo_board 0> -> <&xo_board>. 2. Addressed Adrian minor comments on 009. 3. Other minor changes. Older history:- Changes from v7 -> v8 :- 1. Added patch 005 to add dt bindings for xo_clock. 2. Added patch 009 to factor out sdhci_enable_clock as discussed on v7 series. 2.a. Modified patch 010 by making use of sdhci_enable_clock. 2.b. Addressed Stephen's comment on patch 010 to call clk_set_rate unconditionally. 3. Addressed Stephen comments to remove unncessary one line comments, braces and other minor comments. 4. Added changes from Jeremy in patch 002 for gcc-msm8994 as well for sdcc clk_rcg2_floor_ops. minor comments. v7 was verified on my Nexus 5X (msm8992). Older history :- Below are the changes in v7. Changes from v6 -> v7 :- 1. Removed patch "clk: Add clk_hw_get_clk() helper API to be used by clk providers" in v7 as it was not required. 2. Addressed Stephen review comments on - "clk: qcom: Add rcg ops to return floor value closest to the requested rate" 3. Addressed comments from Stephen to add xo_clock entry in the sdhc clock node. Using the same xo_clock entry from DT to get the clk_rate of xo_clock used in sdhci-msm driver. Patch 04 adds this entry into DT. Patch 05 adds the driver support for xo_clock mentioned above. Hence there is a minor change in Patch05, which can be reviewed and taken into the tree. IMHO, almost all patches are almost done and are ready to be accepted. Will below process work out? Patches 001 & 002 :- (clock changes) - Can go via Stephen's Boyd Tree. Patches 004 & 010 :- (DTS changes) - Can go via Andy Gross. Patches 003, 005-009 & 011-014 :- (sdhci-msm changes) - Adrian's tree. Please let me know in case if anything else is required on above. Changes from v5 -> v6 :- 1. Earlier in v5 series DT node was added to get the clk-rates table needed for sdhci-msm driver. But this is removed in this(v6) patch series and instead the clk changes are done in the clk driver as per Rob H comment. 2. Added clk driver changes(patch 1-3) to provide floor rate values of requested clock for sdhc client. For following boards- apq8084, msm8996, msm8916, msm8974. 3. Other minor patch comments were addressed. Changes from v4 -> v5 :- 1. Added HS400 sdhci-msm controller specific changes:- (Patch 10, 11, 12) 2. Addressed comment from Adrian on Patch 07 @[3]. 3. Addressed comment from Arnd on Patch 03, to directly add clk_table into sdhci_msm_host. [4] 4. Addressed comment from Bjorn to not enforce having clk-rates property in DT for older targets based on discussion at [5] 5. Retained Acks from Adrian on patches (01 & 02 & 06) where there were no changes made while addressing above comments. Older history:- This is v4 version of the patch series. Patches 01, 02, 05 & 06 were Acked-by Adrian. Changes from v3 -> v4 :- 1. Addressed comments from Adrian on Patch 03, 07, 08. 2. Addressed comments from Bjorn on Patch 03. 3. Added clk-rate support for sdhc DT nodes to all MSM platforms. in Pacth 04. 4. Rebased on next branch of Ulf. Changes from v2 -> v3 :- 1. Addded Patch 01 based on Bjorn comment[2] - This fixes/unrolls the poor coding style of read/writes of registers from base sdhci-msm driver. 2. Fixed/unrolled poor style of reads/writes of registers in Patch 02, based on Bjorn comment[2]. Also changed name of flag from use_updated_dll_reset -> use_14lpp_dll_reset. Changes from v1->v2 :- 1. Removed patch 06 & 08 from v1 patch series[1] (which were introducing unnecessary quirks). Instead have implemented __sdhci_msm_set_clock version of sdhci_set_clock in sdhci_msm driver itself in patch 07 of this patch series. 2. Enabled extra quirk (SDHCI_QUIRK2_PRESET_VALUE_BROKEN) in patch 05 of this patch series. Description of patches :- This patchset adds clk-rates & other required changes to upstream sdhci-msm driver from codeaurora tree. It has been tested on a db410c Dragonboard and msm8996 based platform. Patch 0001-0003- Adds support in qcom clk driver to return floor value of requested clock rate instead of ceil rate for sdhc clients. Patch 0004- Adds updated dll sequence for newer controllers which has minor_version >= 0x42. This is required for msm8996. MSM controller HW recommendation is to use the base MCI clock and directly control this MCI clock at GCC in order to change the clk-rate. Patches 06-08 bring in required change for this to sdhci-msm. MSM controller would require 2x clock rate from source for DDR bus speed modes. Patch 09 adds this support. Patch 0010- adds DDR support in DT for sdhc1 of msm8916. Patches 0011-0014- Adds HS400 support to sdhci-msm. [1]:- http://www.spinics.net/lists/linux-mmc/msg38467.html [2]:- http://www.spinics.net/lists/linux-mmc/msg38578.html [3]:- https://patchwork.kernel.org/patch/9289345/ [4]:- https://www.spinics.net/lists/linux-mmc/msg39107.html [5]:- http://www.spinics.net/lists/linux-mmc/msg38749.html [6]:- https://patchwork.kernel.org/patch/9297381/ Rajendra Nayak (2): clk: qcom: Add rcg ops to return floor value closest to the requested rate clk: qcom: Move all sdcc rcgs to use clk_rcg2_floor_ops Ritesh Harjani (12): mmc: sdhci-msm: Change poor style writel/readl of registers ARM: dts: Add xo to sdhc clock node on qcom platforms dt-bindings: sdhci-msm: Add xo value mmc: sdhci-msm: Add get_min_clock() and get_max_clock() callback mmc: sdhci-msm: Enable few quirks mmc: sdhci: Factor out sdhci_enable_clk mmc: sdhci-msm: Implement set_clock callback for sdhci-msm mmc: sdhci-msm: Add clock changes for DDR mode. arm64: dts: qcom: msm8916: Add ddr support to sdhc1 mmc: sdhci-msm: Save the calculated tuning phase mmc: sdhci-msm: Add calibration tuning for CDCLP533 circuit sdhci: sdhci-msm: update dll configuration Venkat Gopalakrishnan (2): mmc: sdhci-msm: Update DLL reset sequence mmc: sdhci-msm: Add HS400 platform support .../devicetree/bindings/mmc/sdhci-msm.txt | 1 + arch/arm/boot/dts/qcom-apq8084.dtsi | 16 +- arch/arm/boot/dts/qcom-msm8974.dtsi | 16 +- arch/arm64/boot/dts/qcom/msm8916.dtsi | 11 +- arch/arm64/boot/dts/qcom/msm8996.dtsi | 9 +- drivers/clk/qcom/clk-rcg.h | 1 + drivers/clk/qcom/clk-rcg2.c | 76 ++- drivers/clk/qcom/common.c | 16 + drivers/clk/qcom/common.h | 2 + drivers/clk/qcom/gcc-apq8084.c | 8 +- drivers/clk/qcom/gcc-msm8916.c | 4 +- drivers/clk/qcom/gcc-msm8974.c | 8 +- drivers/clk/qcom/gcc-msm8994.c | 8 +- drivers/clk/qcom/gcc-msm8996.c | 8 +- drivers/mmc/host/sdhci-msm.c | 626 +++++++++++++++++++-- drivers/mmc/host/sdhci.c | 28 +- drivers/mmc/host/sdhci.h | 1 + 17 files changed, 739 insertions(+), 100 deletions(-) -- The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project. -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
