On 11/05/2016 09:55 PM, Rob Clark wrote:
Split out the hardware pipe specifics from mdp5_plane. To start, the hw pipes are statically assigned to planes, but next step is to assign the hw pipes during plane->atomic_check() based on requested caps (scaling, YUV, etc). And then hw pipe re-assignment if required if required SMP blocks changes. Signed-off-by: Rob Clark <robdclark@xxxxxxxxx> --- drivers/gpu/drm/msm/Makefile | 1 + drivers/gpu/drm/msm/mdp/mdp5/mdp5_kms.c | 126 +++++++++++++++++++----------- drivers/gpu/drm/msm/mdp/mdp5/mdp5_kms.h | 7 +- drivers/gpu/drm/msm/mdp/mdp5/mdp5_pipe.c | 43 ++++++++++ drivers/gpu/drm/msm/mdp/mdp5/mdp5_pipe.h | 39 +++++++++ drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c | 66 +++++++--------- 6 files changed, 197 insertions(+), 85 deletions(-) create mode 100644 drivers/gpu/drm/msm/mdp/mdp5/mdp5_pipe.c create mode 100644 drivers/gpu/drm/msm/mdp/mdp5/mdp5_pipe.h diff --git a/drivers/gpu/drm/msm/Makefile b/drivers/gpu/drm/msm/Makefile index fb5be3e..90f66c4 100644 --- a/drivers/gpu/drm/msm/Makefile +++ b/drivers/gpu/drm/msm/Makefile @@ -37,6 +37,7 @@ msm-y := \ mdp/mdp5/mdp5_irq.o \ mdp/mdp5/mdp5_mdss.o \ mdp/mdp5/mdp5_kms.o \ + mdp/mdp5/mdp5_pipe.o \ mdp/mdp5/mdp5_plane.o \ mdp/mdp5/mdp5_smp.o \ msm_atomic.o \ diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_kms.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_kms.c index f1288c7..d3d45ed 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_kms.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_kms.c @@ -119,6 +119,10 @@ static void mdp5_kms_destroy(struct msm_kms *kms) { struct mdp5_kms *mdp5_kms = to_mdp5_kms(to_mdp_kms(kms)); struct msm_gem_address_space *aspace = mdp5_kms->aspace; + int i; + + for (i = 0; i < mdp5_kms->num_hwpipes; i++) + mdp5_pipe_destroy(mdp5_kms->hwpipes[i]); if (aspace) { aspace->mmu->funcs->detach(aspace->mmu, @@ -323,15 +327,6 @@ static int modeset_init_intf(struct mdp5_kms *mdp5_kms, int intf_num) static int modeset_init(struct mdp5_kms *mdp5_kms) { - static const enum mdp5_pipe rgb_planes[] = { - SSPP_RGB0, SSPP_RGB1, SSPP_RGB2, SSPP_RGB3, - }; - static const enum mdp5_pipe vig_planes[] = { - SSPP_VIG0, SSPP_VIG1, SSPP_VIG2, SSPP_VIG3, - }; - static const enum mdp5_pipe dma_planes[] = { - SSPP_DMA0, SSPP_DMA1, - }; struct drm_device *dev = mdp5_kms->dev; struct msm_drm_private *priv = dev->dev_private; const struct mdp5_cfg_hw *hw_cfg; @@ -339,58 +334,34 @@ static int modeset_init(struct mdp5_kms *mdp5_kms) hw_cfg = mdp5_cfg_get_hw_config(mdp5_kms->cfg); - /* construct CRTCs and their private planes: */ - for (i = 0; i < hw_cfg->pipe_rgb.count; i++) { + /* Construct planes equaling the number of hw pipes, and CRTCs + * for the N layer-mixers (LM). The first N planes become primary + * planes for the CRTCs, with the remainder as overlay planes: + */
Jfyi, we might need to change this a bit in the future. It'll be better to get the max number of displays connected on our platform via parsing DT, etc, and calculate CRTCs based on that, and not number of layermixers. Maybe add a couple for writeback too. This way, we get the right number of CRTCs, and we don't rely on #LMs, since we can have 2 per crtc in the future. Reviewed-by: Archit Taneja <architt@xxxxxxxxxxxxxx> -- Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html