Add DSI and panel nodes to get graphics up and running
on the Nexus7.
This still depends on the panel driver being present
along with the rpmclk code.
Feedback would be greatly appreciated!
Cc: Archit Taneja <architt@xxxxxxxxxxxxxx>
Cc: vinay simha <vinaysimha@xxxxxxxxxxxxxxxxxxxx>
Cc: andy.gross@xxxxxxxxxx
Cc: robdclark@xxxxxxxxx
Cc: linux-arm-msm@xxxxxxxxxxxxxxx
Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx
Signed-off-by: John Stultz <john.stultz@xxxxxxxxxx>
---
v2: Integrated cleanups from Vinay and Archit
arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts | 63 +++++++++++++++++++++-
1 file changed, 61 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index ff856c3..7637092 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -99,6 +99,7 @@
l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
+ regulator-always-on;
};
/* msm_otg-HSUSB_3p3 */
@@ -133,13 +134,14 @@
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
bias-pull-down;
+ regulator-always-on;
};
/* pwm_power for backlight */
l17 {
regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3600000>;
- bias-pull-down;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
};
/* camera, qdsp6 */
@@ -184,6 +186,63 @@
};
};
+ mdp@5100000 {
+ status = "okay";
+ ports {
+ port@1 {
+ mdp_dsi1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: mdss_dsi@4700000 {
+ status = "okay";
+ vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
+ vdd-supply = <&pm8921_l8>;
+ vddio-supply = <&pm8921_lvs7>;
+ avdd-supply = <&pm8921_l11>;
+ vcss-supply = <&ext_3p3v>;
+
+ panel@0 {
+ reg = <0>;
+ compatible = "jdi,lt070me05000";
+
+ vddp-supply = <&pm8921_l17>;
+ iovcc-supply = <&pm8921_lvs7>;
+
+ enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
+ dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+ ports {
+ port@0 {
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp_dsi1_out>;
+ };
+ };
+
+ port@1 {
+ dsi0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+ };
+
+ dsi-phy@4700200 {
+ status = "okay";
+ vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
+ };
+
gsbi@16200000 {
status = "okay";
qcom,mode = <GSBI_PROT_I2C>;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
