[PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Some Qualcomm PMICs have a misc device that performs USB id pin
detection via an interrupt. When the interrupt triggers, we
should read the interrupt line to see if it has gone high or low.
If the interrupt is low then the ID pin is grounded, and if the
interrupt is high then the ID pin is being held high.

Cc: Roger Quadros <rogerq@xxxxxx>
Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
Signed-off-by: Stephen Boyd <stephen.boyd@xxxxxxxxxx>
---

Changes from v1:
 * Fixed Makefile ordering
 * Fixed up copyright markings

 .../bindings/extcon/qcom,pm8941-misc.txt           |  41 +++++
 drivers/extcon/Kconfig                             |   6 +
 drivers/extcon/Makefile                            |   1 +
 drivers/extcon/extcon-qcom-spmi-misc.c             | 167 +++++++++++++++++++++
 4 files changed, 215 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt
 create mode 100644 drivers/extcon/extcon-qcom-spmi-misc.c

diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt
new file mode 100644
index 000000000000..35383adb10f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt
@@ -0,0 +1,41 @@
+Qualcomm's PM8941 USB ID Extcon device
+
+Some Qualcomm PMICs have a "misc" module that can be used to detect when
+the USB ID pin has been pulled low or high.
+
+PROPERTIES
+
+- compatible:
+    Usage: required
+    Value type: <string>
+    Definition: Should contain "qcom,pm8941-misc";
+
+- reg:
+    Usage: required
+    Value type: <u32>
+    Definition: Should contain the offset to the misc address space
+
+- interrupts:
+    Usage: required
+    Value type: <prop-encoded-array>
+    Definition: Should contain the usb id interrupt
+
+- interrupt-names:
+    Usage: required
+    Value type: <stringlist>
+    Definition: Should contain the string "usb_id" for the usb id interrupt
+
+Example:
+
+	pmic {
+		usb_id: misc@900 {
+			compatible = "qcom,pm8941-misc";
+			reg = <0x900>;
+			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "usb_id";
+		};
+	}
+
+	usb-controller {
+		extcon = <&usb_id>;
+	};
diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
index 3d89e60a3e71..04788d92ea52 100644
--- a/drivers/extcon/Kconfig
+++ b/drivers/extcon/Kconfig
@@ -96,6 +96,12 @@ config EXTCON_PALMAS
 	  Say Y here to enable support for USB peripheral and USB host
 	  detection by palmas usb.
 
+config EXTCON_QCOM_SPMI_MISC
+	tristate "Qualcomm USB extcon support"
+	help
+	  Say Y here to enable SPMI PMIC based USB cable detection
+	  support on Qualcomm PMICs such as PM8941.
+
 config EXTCON_RT8973A
 	tristate "Richtek RT8973A EXTCON support"
 	depends on I2C
diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
index 972c813c375b..31a0a999c4fb 100644
--- a/drivers/extcon/Makefile
+++ b/drivers/extcon/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_EXTCON_MAX77693)	+= extcon-max77693.o
 obj-$(CONFIG_EXTCON_MAX77843)	+= extcon-max77843.o
 obj-$(CONFIG_EXTCON_MAX8997)	+= extcon-max8997.o
 obj-$(CONFIG_EXTCON_PALMAS)	+= extcon-palmas.o
+obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o
 obj-$(CONFIG_EXTCON_RT8973A)	+= extcon-rt8973a.o
 obj-$(CONFIG_EXTCON_SM5502)	+= extcon-sm5502.o
 obj-$(CONFIG_EXTCON_USB_GPIO)	+= extcon-usb-gpio.o
diff --git a/drivers/extcon/extcon-qcom-spmi-misc.c b/drivers/extcon/extcon-qcom-spmi-misc.c
new file mode 100644
index 000000000000..1b8e24494c60
--- /dev/null
+++ b/drivers/extcon/extcon-qcom-spmi-misc.c
@@ -0,0 +1,167 @@
+/**
+ * Based on extcon-usb-gpio.c
+ *
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/extcon.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+
+#define USB_ID_DEBOUNCE_MS	5	/* ms */
+
+struct qcom_usb_extcon_info {
+	struct extcon_dev *edev;
+	int irq;
+	struct delayed_work wq_detcable;
+	unsigned long debounce_jiffies;
+};
+
+static const unsigned int qcom_usb_extcon_cable[] = {
+	EXTCON_USB_HOST,
+	EXTCON_NONE,
+};
+
+static void qcom_usb_extcon_detect_cable(struct work_struct *work)
+{
+	bool id;
+	int ret;
+	struct qcom_usb_extcon_info *info = container_of(to_delayed_work(work),
+						    struct qcom_usb_extcon_info,
+						    wq_detcable);
+
+	/* check ID and update cable state */
+	ret = irq_get_irqchip_state(info->irq, IRQCHIP_STATE_LINE_LEVEL, &id);
+	if (ret)
+		return;
+
+	extcon_set_cable_state_(info->edev, EXTCON_USB_HOST, !id);
+}
+
+static irqreturn_t qcom_usb_irq_handler(int irq, void *dev_id)
+{
+	struct qcom_usb_extcon_info *info = dev_id;
+
+	queue_delayed_work(system_power_efficient_wq, &info->wq_detcable,
+			   info->debounce_jiffies);
+
+	return IRQ_HANDLED;
+}
+
+static int qcom_usb_extcon_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct qcom_usb_extcon_info *info;
+	int ret;
+
+	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	info->edev = devm_extcon_dev_allocate(dev, qcom_usb_extcon_cable);
+	if (IS_ERR(info->edev)) {
+		dev_err(dev, "failed to allocate extcon device\n");
+		return -ENOMEM;
+	}
+
+	ret = devm_extcon_dev_register(dev, info->edev);
+	if (ret < 0) {
+		dev_err(dev, "failed to register extcon device\n");
+		return ret;
+	}
+
+	info->debounce_jiffies = msecs_to_jiffies(USB_ID_DEBOUNCE_MS);
+	INIT_DELAYED_WORK(&info->wq_detcable, qcom_usb_extcon_detect_cable);
+
+	info->irq = platform_get_irq_byname(pdev, "usb_id");
+	if (info->irq < 0)
+		return info->irq;
+
+	ret = devm_request_threaded_irq(dev, info->irq, NULL,
+					qcom_usb_irq_handler,
+					IRQF_TRIGGER_RISING |
+					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+					pdev->name, info);
+	if (ret < 0) {
+		dev_err(dev, "failed to request handler for ID IRQ\n");
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, info);
+	device_init_wakeup(dev, 1);
+
+	/* Perform initial detection */
+	qcom_usb_extcon_detect_cable(&info->wq_detcable.work);
+
+	return 0;
+}
+
+static int qcom_usb_extcon_remove(struct platform_device *pdev)
+{
+	struct qcom_usb_extcon_info *info = platform_get_drvdata(pdev);
+
+	cancel_delayed_work_sync(&info->wq_detcable);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int qcom_usb_extcon_suspend(struct device *dev)
+{
+	struct qcom_usb_extcon_info *info = dev_get_drvdata(dev);
+	int ret = 0;
+
+	if (device_may_wakeup(dev))
+		ret = enable_irq_wake(info->irq);
+
+	return ret;
+}
+
+static int qcom_usb_extcon_resume(struct device *dev)
+{
+	struct qcom_usb_extcon_info *info = dev_get_drvdata(dev);
+	int ret = 0;
+
+	if (device_may_wakeup(dev))
+		ret = disable_irq_wake(info->irq);
+
+	return ret;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(qcom_usb_extcon_pm_ops,
+			 qcom_usb_extcon_suspend, qcom_usb_extcon_resume);
+
+static const struct of_device_id qcom_usb_extcon_dt_match[] = {
+	{ .compatible = "qcom,pm8941-misc", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_extcon_dt_match);
+
+static struct platform_driver qcom_usb_extcon_driver = {
+	.probe		= qcom_usb_extcon_probe,
+	.remove		= qcom_usb_extcon_remove,
+	.driver		= {
+		.name	= "extcon-pm8941-misc",
+		.pm	= &qcom_usb_extcon_pm_ops,
+		.of_match_table = qcom_usb_extcon_dt_match,
+	},
+};
+module_platform_driver(qcom_usb_extcon_driver);
+
+MODULE_DESCRIPTION("QCOM USB ID extcon driver");
+MODULE_LICENSE("GPL v2");
-- 
2.9.0.rc2.8.ga28705d

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux