On Wed, Mar 19, 2025 at 03:12:50PM +0100, Konrad Dybcio wrote:
> On 3/19/25 12:06 PM, Dmitry Baryshkov wrote:
> > On Wed, Mar 19, 2025 at 04:16:33PM +0530, Krishna Chaitanya Chundru wrote:
> >>
> >>
> >> On 3/19/2025 3:51 PM, Dmitry Baryshkov wrote:
> >>> On Wed, Mar 19, 2025 at 03:46:00PM +0530, Krishna Chaitanya Chundru wrote:
> >>>>
> >>>>
> >>>> On 3/19/2025 3:43 PM, Dmitry Baryshkov wrote:
> >>>>> On Wed, Mar 19, 2025 at 09:14:22AM +0530, Krishna Chaitanya Chundru wrote:
> >>>>>>
> >>>>>>
> >>>>>> On 3/18/2025 10:30 PM, Dmitry Baryshkov wrote:
> >>>>>>> On Tue, 18 Mar 2025 at 18:11, Krishna Chaitanya Chundru
> >>>>>>> <krishna.chundru@xxxxxxxxxxxxxxxx> wrote:
> >>>>>>>>
> >>>>>>>>
> >>>>>>>>
> >>>>>>>> On 3/17/2025 4:57 PM, Dmitry Baryshkov wrote:
> >>>>>>>>> On Tue, Feb 25, 2025 at 03:03:59PM +0530, Krishna Chaitanya Chundru wrote:
> >>>>>>>>>> Add a node for the TC956x PCIe switch, which has three downstream ports.
> >>>>>>>>>> Two embedded Ethernet devices are present on one of the downstream ports.
> >>>>>>>>>>
> >>>>>>>>>> Power to the TC956x is supplied through two LDO regulators, controlled by
> >>>>>>>>>> two GPIOs, which are added as fixed regulators. Configure the TC956x
> >>>>>>>>>> through I2C.
> >>>>>>>>>>
> >>>>>>>>>> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@xxxxxxxxxxxxxxxx>
> >>>>>>>>>> Reviewed-by: Bjorn Andersson <andersson@xxxxxxxxxx>
> >>>>>>>>>> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
> >>>>>>>>>> ---
> >>>>>>>>>> arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 116 +++++++++++++++++++++++++++
> >>>>>>>>>> arch/arm64/boot/dts/qcom/sc7280.dtsi | 2 +-
> >>>>>>>>>> 2 files changed, 117 insertions(+), 1 deletion(-)
> >>>>>>>>>>
> >>>>>>>>>> @@ -735,6 +760,75 @@ &pcie1_phy {
> >>>>>>>>>> status = "okay";
> >>>>>>>>>> };
> >>>>>>>>>>
> >>>>>>>>>> +&pcie1_port {
> >>>>>>>>>> + pcie@0,0 {
> >>>>>>>>>> + compatible = "pci1179,0623", "pciclass,0604";
> >>>>>>>>>> + reg = <0x10000 0x0 0x0 0x0 0x0>;
> >>>>>>>>>> + #address-cells = <3>;
> >>>>>>>>>> + #size-cells = <2>;
> >>>>>>>>>> +
> >>>>>>>>>> + device_type = "pci";
> >>>>>>>>>> + ranges;
> >>>>>>>>>> + bus-range = <0x2 0xff>;
> >>>>>>>>>> +
> >>>>>>>>>> + vddc-supply = <&vdd_ntn_0p9>;
> >>>>>>>>>> + vdd18-supply = <&vdd_ntn_1p8>;
> >>>>>>>>>> + vdd09-supply = <&vdd_ntn_0p9>;
> >>>>>>>>>> + vddio1-supply = <&vdd_ntn_1p8>;
> >>>>>>>>>> + vddio2-supply = <&vdd_ntn_1p8>;
> >>>>>>>>>> + vddio18-supply = <&vdd_ntn_1p8>;
> >>>>>>>>>> +
> >>>>>>>>>> + i2c-parent = <&i2c0 0x77>;
> >>>>>>>>>> +
> >>>>>>>>>> + reset-gpios = <&pm8350c_gpios 1 GPIO_ACTIVE_LOW>;
> >>>>>>>>>> +
> >>>>>>>>>
> >>>>>>>>> I think I've responded here, but I'm not sure where the message went:
> >>>>>>>>> please add pinctrl entry for this pin.
> >>>>>>>>>
> >>>>>>>> Do we need to also add pinctrl property for this node and refer the
> >>>>>>>> pinctrl entry for this pin?
> >>>>>>>
> >>>>>>> I think that is what I've asked for, was that not?
> >>>>>> Currently there is no pincntrl property defined for this.
> >>>>>
> >>>>> Does it need to be defined separately / specially?
> >>>>>
> >>>> yes we need to define this property now.
> >>>
> >>> Could you please point out existing schema files defining those
> >>> properties?
> >> sorry I was not able to get which schema file you are requesting for,
> >> if it is tc956x it is in this series only.
> >>
> >> What I understood from these conversation is we need to define pinctrl
> >> property and refer the reset gpio pin in next series. If it was wrong
> >> please correct me.
> >
> > You claimed that pinctrl properties (there are several of those) are to
> > be defined in the schema for TC956x. I asked you to point out other
> > schema files which define those properties for the devices that use
> > GPIO pins.
>
> pinctrl-x is part of common schema (see gh/devicetree-org/dt-schema/)
Right :-)
So there is no need to define anything, they just need to be added to
the DTS file.
--
With best wishes
Dmitry
