On Thu, Mar 06, 2025 at 04:46:09PM +0530, Manikanta Mylavarapu wrote:
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ5424 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxxxx>
> Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@xxxxxxxxxxx>
When validating this against linux-next DT bindings I get:
arch/arm64/boot/dts/qcom/ipq5424-rdp466.dtb: pcie@f8000: reg: [[0, 1015808, 0, 12288], [0, 1073741824, 0, 3868], [0, 1073745696, 0, 168], [0, 1073745920, 0, 4096], [0, 1074790400, 0, 4096], [0, 1040384, 0, 4096]] is too long
arch/arm64/boot/dts/qcom/ipq5424-rdp466.dtb: pcie@f8000: reg-names:0: 'dbi' was expected
arch/arm64/boot/dts/qcom/ipq5424-rdp466.dtb: pcie@f8000: reg-names:1: 'elbi' was expected
arch/arm64/boot/dts/qcom/ipq5424-rdp466.dtb: pcie@f8000: reg-names:2: 'atu' was expected
arch/arm64/boot/dts/qcom/ipq5424-rdp466.dtb: pcie@f8000: reg-names:3: 'parf' was expected
arch/arm64/boot/dts/qcom/ipq5424-rdp466.dtb: pcie@f8000: reg-names: ['parf', 'dbi', 'elbi', 'atu', 'config', 'mhi'] is too long
Are we still missing something?
Regards,
Bjorn
> ---
> Changes in V5:
> - Pick up R-b tag.
> - Updated pcie node order based on unit address.
> - Updated the dbi address space size from 0xf1d to 0xf1c
> in all pcie controller nodes.
> - Rebased on linux-next tip.
>
> arch/arm64/boot/dts/qcom/ipq5424.dtsi | 514 +++++++++++++++++++++++++-
> 1 file changed, 510 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq5424.dtsi b/arch/arm64/boot/dts/qcom/ipq5424.dtsi
> index 7a7ad700a382..ff6faffc3b48 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5424.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq5424.dtsi
> @@ -9,6 +9,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,ipq5424-gcc.h>
> #include <dt-bindings/reset/qcom,ipq5424-gcc.h>
> +#include <dt-bindings/interconnect/qcom,ipq5424.h>
> #include <dt-bindings/gpio/gpio.h>
>
> / {
> @@ -152,6 +153,258 @@ soc@0 {
> #size-cells = <2>;
> ranges = <0 0 0 0 0x10 0>;
>
> + pcie0: pcie@80000 {
> + compatible = "qcom,pcie-ipq5424", "qcom,pcie-ipq9574";
> + reg = <0x0 0x00080000 0x0 0x3000>,
> + <0x0 0x70000000 0x0 0xf1c>,
> + <0x0 0x70000f20 0x0 0xa8>,
> + <0x0 0x70001000 0x0 0x1000>,
> + <0x0 0x70100000 0x0 0x1000>,
> + <0x0 0x00086000 0x0 0x1000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> + device_type = "pci";
> + linux,pci-domain = <0>;
> + num-lanes = <1>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x70200000 0x0 0x00100000>,
> + <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x0fd00000>;
> +
> + msi-map = <0x0 &intc 0x0 0x1000>;
> +
> + interrupts = <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 427 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 428 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 432 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7",
> + "global";
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0x0 0x0 0x0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 436 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 437 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc GCC_PCIE0_AXI_M_CLK>,
> + <&gcc GCC_PCIE0_AXI_S_CLK>,
> + <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
> + <&gcc GCC_PCIE0_RCHNG_CLK>,
> + <&gcc GCC_PCIE0_AHB_CLK>,
> + <&gcc GCC_PCIE0_AUX_CLK>;
> + clock-names = "axi_m",
> + "axi_s",
> + "axi_bridge",
> + "rchng",
> + "ahb",
> + "aux";
> +
> + assigned-clocks = <&gcc GCC_PCIE0_RCHNG_CLK>;
> + assigned-clock-rates = <100000000>;
> +
> + resets = <&gcc GCC_PCIE0_PIPE_ARES>,
> + <&gcc GCC_PCIE0_CORE_STICKY_RESET>,
> + <&gcc GCC_PCIE0_AXI_S_STICKY_RESET>,
> + <&gcc GCC_PCIE0_AXI_S_ARES>,
> + <&gcc GCC_PCIE0_AXI_M_STICKY_RESET>,
> + <&gcc GCC_PCIE0_AXI_M_ARES>,
> + <&gcc GCC_PCIE0_AUX_ARES>,
> + <&gcc GCC_PCIE0_AHB_ARES>;
> + reset-names = "pipe",
> + "sticky",
> + "axi_s_sticky",
> + "axi_s",
> + "axi_m_sticky",
> + "axi_m",
> + "aux",
> + "ahb";
> +
> + phys = <&pcie0_phy>;
> + phy-names = "pciephy";
> + interconnects = <&gcc MASTER_ANOC_PCIE0 &gcc SLAVE_ANOC_PCIE0>,
> + <&gcc MASTER_CNOC_PCIE0 &gcc SLAVE_CNOC_PCIE0>;
> + interconnect-names = "pcie-mem", "cpu-pcie";
> +
> + status = "disabled";
> +
> + pcie@0 {
> + device_type = "pci";
> + reg = <0x0 0x0 0x0 0x0 0x0>;
> + bus-range = <0x01 0xff>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> + };
> +
> + pcie0_phy: phy@84000 {
> + compatible = "qcom,ipq5424-qmp-gen3x1-pcie-phy",
> + "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> + reg = <0x0 0x00084000 0x0 0x2000>;
> + clocks = <&gcc GCC_PCIE0_AUX_CLK>,
> + <&gcc GCC_PCIE0_AHB_CLK>,
> + <&gcc GCC_PCIE0_PIPE_CLK>;
> + clock-names = "aux", "cfg_ahb", "pipe";
> +
> + assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + #clock-cells = <0>;
> + clock-output-names = "gcc_pcie0_pipe_clk_src";
> +
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> +
> + pcie1: pcie@88000 {
> + compatible = "qcom,pcie-ipq5424", "qcom,pcie-ipq9574";
> + reg = <0x0 0x00088000 0x0 0x3000>,
> + <0x0 0x60000000 0x0 0xf1c>,
> + <0x0 0x60000f20 0x0 0xa8>,
> + <0x0 0x60001000 0x0 0x1000>,
> + <0x0 0x60100000 0x0 0x1000>,
> + <0x0 0x0008e000 0x0 0x1000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> + device_type = "pci";
> + linux,pci-domain = <1>;
> + num-lanes = <1>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x00100000>,
> + <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x0fd00000>;
> +
> + msi-map = <0x0 &intc 0x0 0x1000>;
> +
> + interrupts = <GIC_SPI 440 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 441 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 442 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 443 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 447 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7",
> + "global";
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0x0 0x0 0x0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 449 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 450 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 451 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 452 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc GCC_PCIE1_AXI_M_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
> + <&gcc GCC_PCIE1_RCHNG_CLK>,
> + <&gcc GCC_PCIE1_AHB_CLK>,
> + <&gcc GCC_PCIE1_AUX_CLK>;
> + clock-names = "axi_m",
> + "axi_s",
> + "axi_bridge",
> + "rchng",
> + "ahb",
> + "aux";
> +
> + assigned-clocks = <&gcc GCC_PCIE1_RCHNG_CLK>;
> + assigned-clock-rates = <100000000>;
> +
> + resets = <&gcc GCC_PCIE1_PIPE_ARES>,
> + <&gcc GCC_PCIE1_CORE_STICKY_RESET>,
> + <&gcc GCC_PCIE1_AXI_S_STICKY_RESET>,
> + <&gcc GCC_PCIE1_AXI_S_ARES>,
> + <&gcc GCC_PCIE1_AXI_M_STICKY_RESET>,
> + <&gcc GCC_PCIE1_AXI_M_ARES>,
> + <&gcc GCC_PCIE1_AUX_ARES>,
> + <&gcc GCC_PCIE1_AHB_ARES>;
> + reset-names = "pipe",
> + "sticky",
> + "axi_s_sticky",
> + "axi_s",
> + "axi_m_sticky",
> + "axi_m",
> + "aux",
> + "ahb";
> +
> + phys = <&pcie1_phy>;
> + phy-names = "pciephy";
> + interconnects = <&gcc MASTER_ANOC_PCIE1 &gcc SLAVE_ANOC_PCIE1>,
> + <&gcc MASTER_CNOC_PCIE1 &gcc SLAVE_CNOC_PCIE1>;
> + interconnect-names = "pcie-mem", "cpu-pcie";
> +
> + status = "disabled";
> +
> + pcie@0 {
> + device_type = "pci";
> + reg = <0x0 0x0 0x0 0x0 0x0>;
> + bus-range = <0x01 0xff>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> + };
> +
> + pcie1_phy: phy@8c000 {
> + compatible = "qcom,ipq5424-qmp-gen3x1-pcie-phy",
> + "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> + reg = <0x0 0x0008c000 0x0 0x2000>;
> + clocks = <&gcc GCC_PCIE1_AUX_CLK>,
> + <&gcc GCC_PCIE1_AHB_CLK>,
> + <&gcc GCC_PCIE1_PIPE_CLK>;
> + clock-names = "aux", "cfg_ahb", "pipe";
> +
> + assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + #clock-cells = <0>;
> + clock-output-names = "gcc_pcie1_pipe_clk_src";
> +
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> +
> efuse@a4000 {
> compatible = "qcom,ipq5424-qfprom", "qcom,qfprom";
> reg = <0 0x000a4000 0 0x741>;
> @@ -209,6 +462,259 @@ tsens_base1: base1@41a {
> };
> };
>
> + pcie2: pcie@f0000 {
> + compatible = "qcom,pcie-ipq5424", "qcom,pcie-ipq9574";
> + reg = <0x0 0x000f0000 0x0 0x3000>,
> + <0x0 0x50000000 0x0 0xf1c>,
> + <0x0 0x50000f20 0x0 0xa8>,
> + <0x0 0x50001000 0x0 0x1000>,
> + <0x0 0x50100000 0x0 0x1000>,
> + <0x0 0x000f6000 0x0 0x1000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> + device_type = "pci";
> + linux,pci-domain = <2>;
> + num-lanes = <2>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x50200000 0x0 0x00100000>,
> + <0x02000000 0x0 0x50300000 0x0 0x50300000 0x0 0x0fd00000>;
> +
> + msi-map = <0x0 &intc 0x0 0x1000>;
> +
> + interrupts = <GIC_SPI 455 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 460 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7",
> + "global";
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0x0 0x0 0x0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 464 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 465 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 466 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 467 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc GCC_PCIE2_AXI_M_CLK>,
> + <&gcc GCC_PCIE2_AXI_S_CLK>,
> + <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
> + <&gcc GCC_PCIE2_RCHNG_CLK>,
> + <&gcc GCC_PCIE2_AHB_CLK>,
> + <&gcc GCC_PCIE2_AUX_CLK>;
> + clock-names = "axi_m",
> + "axi_s",
> + "axi_bridge",
> + "rchng",
> + "ahb",
> + "aux";
> +
> + assigned-clocks = <&gcc GCC_PCIE2_RCHNG_CLK>;
> + assigned-clock-rates = <100000000>;
> +
> + resets = <&gcc GCC_PCIE2_PIPE_ARES>,
> + <&gcc GCC_PCIE2_CORE_STICKY_RESET>,
> + <&gcc GCC_PCIE2_AXI_S_STICKY_RESET>,
> + <&gcc GCC_PCIE2_AXI_S_ARES>,
> + <&gcc GCC_PCIE2_AXI_M_STICKY_RESET>,
> + <&gcc GCC_PCIE2_AXI_M_ARES>,
> + <&gcc GCC_PCIE2_AUX_ARES>,
> + <&gcc GCC_PCIE2_AHB_ARES>;
> + reset-names = "pipe",
> + "sticky",
> + "axi_s_sticky",
> + "axi_s",
> + "axi_m_sticky",
> + "axi_m",
> + "aux",
> + "ahb";
> +
> + phys = <&pcie2_phy>;
> + phy-names = "pciephy";
> + interconnects = <&gcc MASTER_ANOC_PCIE2 &gcc SLAVE_ANOC_PCIE2>,
> + <&gcc MASTER_CNOC_PCIE2 &gcc SLAVE_CNOC_PCIE2>;
> + interconnect-names = "pcie-mem", "cpu-pcie";
> +
> + status = "disabled";
> +
> + pcie@0 {
> + device_type = "pci";
> + reg = <0x0 0x0 0x0 0x0 0x0>;
> + bus-range = <0x01 0xff>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> + };
> +
> + pcie2_phy: phy@f4000 {
> + compatible = "qcom,ipq5424-qmp-gen3x2-pcie-phy",
> + "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> + reg = <0x0 0x000f4000 0x0 0x2000>;
> + clocks = <&gcc GCC_PCIE2_AUX_CLK>,
> + <&gcc GCC_PCIE2_AHB_CLK>,
> + <&gcc GCC_PCIE2_PIPE_CLK>;
> + clock-names = "aux", "cfg_ahb", "pipe";
> +
> + assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE2_PHY_BCR>,
> + <&gcc GCC_PCIE2PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + #clock-cells = <0>;
> + clock-output-names = "gcc_pcie2_pipe_clk_src";
> +
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> +
> + pcie3: pcie@f8000 {
> + compatible = "qcom,pcie-ipq5424", "qcom,pcie-ipq9574";
> + reg = <0x0 0x000f8000 0x0 0x3000>,
> + <0x0 0x40000000 0x0 0xf1c>,
> + <0x0 0x40000f20 0x0 0xa8>,
> + <0x0 0x40001000 0x0 0x1000>,
> + <0x0 0x40100000 0x0 0x1000>,
> + <0x0 0x000fe000 0x0 0x1000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> + device_type = "pci";
> + linux,pci-domain = <3>;
> + num-lanes = <2>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x00100000>,
> + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x0fd00000>;
> +
> + msi-map = <0x0 &intc 0x0 0x1000>;
> +
> + interrupts = <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 476 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7",
> + "global";
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0x0 0x0 0x0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 479 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 480 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 481 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 482 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc GCC_PCIE3_AXI_M_CLK>,
> + <&gcc GCC_PCIE3_AXI_S_CLK>,
> + <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
> + <&gcc GCC_PCIE3_RCHNG_CLK>,
> + <&gcc GCC_PCIE3_AHB_CLK>,
> + <&gcc GCC_PCIE3_AUX_CLK>;
> + clock-names = "axi_m",
> + "axi_s",
> + "axi_bridge",
> + "rchng",
> + "ahb",
> + "aux";
> +
> + assigned-clocks = <&gcc GCC_PCIE3_RCHNG_CLK>;
> + assigned-clock-rates = <100000000>;
> +
> + resets = <&gcc GCC_PCIE3_PIPE_ARES>,
> + <&gcc GCC_PCIE3_CORE_STICKY_RESET>,
> + <&gcc GCC_PCIE3_AXI_S_STICKY_RESET>,
> + <&gcc GCC_PCIE3_AXI_S_ARES>,
> + <&gcc GCC_PCIE3_AXI_M_STICKY_RESET>,
> + <&gcc GCC_PCIE3_AXI_M_ARES>,
> + <&gcc GCC_PCIE3_AUX_ARES>,
> + <&gcc GCC_PCIE3_AHB_ARES>;
> + reset-names = "pipe",
> + "sticky",
> + "axi_s_sticky",
> + "axi_s",
> + "axi_m_sticky",
> + "axi_m",
> + "aux",
> + "ahb";
> +
> + phys = <&pcie3_phy>;
> + phy-names = "pciephy";
> + interconnects = <&gcc MASTER_ANOC_PCIE3 &gcc SLAVE_ANOC_PCIE3>,
> + <&gcc MASTER_CNOC_PCIE3 &gcc SLAVE_CNOC_PCIE3>;
> + interconnect-names = "pcie-mem", "cpu-pcie";
> +
> + status = "disabled";
> +
> + pcie@0 {
> + device_type = "pci";
> + reg = <0x0 0x0 0x0 0x0 0x0>;
> + bus-range = <0x01 0xff>;
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> + };
> +
> + pcie3_phy: phy@fc000 {
> + compatible = "qcom,ipq5424-qmp-gen3x2-pcie-phy",
> + "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> + reg = <0x0 0x000fc000 0x0 0x2000>;
> + clocks = <&gcc GCC_PCIE3_AUX_CLK>,
> + <&gcc GCC_PCIE3_AHB_CLK>,
> + <&gcc GCC_PCIE3_PIPE_CLK>;
> + clock-names = "aux", "cfg_ahb", "pipe";
> +
> + assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
> + assigned-clock-rates = <20000000>;
> +
> + resets = <&gcc GCC_PCIE3_PHY_BCR>,
> + <&gcc GCC_PCIE3PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> +
> + #clock-cells = <0>;
> + clock-output-names = "gcc_pcie3_pipe_clk_src";
> +
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> +
> tsens: thermal-sensor@4a9000 {
> compatible = "qcom,ipq5424-tsens";
> reg = <0 0x004a9000 0 0x1000>,
> @@ -276,10 +782,10 @@ gcc: clock-controller@1800000 {
> reg = <0 0x01800000 0 0x40000>;
> clocks = <&xo_board>,
> <&sleep_clk>,
> - <0>,
> - <0>,
> - <0>,
> - <0>,
> + <&pcie0_phy>,
> + <&pcie1_phy>,
> + <&pcie2_phy>,
> + <&pcie3_phy>,
> <0>;
> #clock-cells = <1>;
> #reset-cells = <1>;
> --
> 2.34.1
>
