Re: [PATCH v4 8/9] mmc: sdhci-msm: Add clock changes for DDR mode.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Adrian,


On 8/29/2016 6:47 PM, Adrian Hunter wrote:
On 24/08/16 13:03, Ritesh Harjani wrote:
SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.

Signed-off-by: Ritesh Harjani <riteshh@xxxxxxxxxxxxxx>
---
 drivers/mmc/host/sdhci-msm.c | 22 ++++++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 853639b..538594c 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -667,21 +667,35 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
-	u32 msm_clock = 0;
+	struct mmc_ios curr_ios = host->mmc->ios;
+	u32 msm_clock, ddr_clock;
 	int rc = 0;

 	if (!clock)
 		goto out;

-	if (clock != msm_host->clk_rate) {
-		msm_clock = sdhci_msm_get_msm_clk_rate(host, clock);
+	msm_clock = sdhci_msm_get_msm_clk_rate(host, clock);
+	if ((curr_ios.timing == MMC_TIMING_UHS_DDR50) ||
+		(curr_ios.timing == MMC_TIMING_MMC_DDR52) ||
+		(curr_ios.timing == MMC_TIMING_MMC_HS400)) {
+		/*
+		 * The SDHC requires internal clock frequency to be double the
+		 * actual clock that will be set for DDR mode. The controller
+		 * uses the faster clock(100/400MHz) for some of its parts and
+		 * send the actual required clock (50/200MHz) to the card.
+		 */
+		ddr_clock = clock * 2;
+		msm_clock = sdhci_msm_get_msm_clk_rate(host, ddr_clock);
+	}
+

Could be slightly simpler e.g.

	if ((curr_ios.timing == MMC_TIMING_UHS_DDR50) ||
	    (curr_ios.timing == MMC_TIMING_MMC_DDR52) ||
	    (curr_ios.timing == MMC_TIMING_MMC_HS400)) {
		/*
		 * The SDHC requires internal clock frequency to be double the
		 * actual clock that will be set for DDR mode. The controller
		 * uses the faster clock(100/400MHz) for some of its parts and
		 * send the actual required clock (50/200MHz) to the card.
		 */
		clock *= 2;
	}
	msm_clock = sdhci_msm_get_msm_clk_rate(host, clock);
Sure. Done.



+	if (msm_clock != msm_host->clk_rate) {
 		rc = clk_set_rate(msm_host->clk, msm_clock);
 		if (rc) {
 			pr_err("%s: failed to set clock at rate %u, requested clock rate %u\n",
 				mmc_hostname(host->mmc), msm_clock, clock);
 			goto out;
 		}
-		msm_host->clk_rate = clock;
+		msm_host->clk_rate = msm_clock;
 		pr_debug("%s: setting clock at rate %lu\n",
 			mmc_hostname(host->mmc), clk_get_rate(msm_host->clk));
 	}


--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux