Florian Fainelli wrote:
On 08/11/2016 02:34 PM, Timur Tabi wrote:
>Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
>This driver supports the following features:
>1) Checksum offload.
>2) Interrupt coalescing support.
>3) SGMII phy.
>4) phylib interface for external phy
OK, so this is looking good now, just a few nits, feel free to submit as
clean up patches, would this one be accepted.
I will post a v9.
>+soc {
>+ #address-cells = <1>;
>+ #size-cells = <1>;
>+ dma-ranges = <0 0 0xffffffff>;
>+
>+ emac0: ethernet@feb20000 {
>+ compatible = "qcom,fsm9900-emac";
>+ #address-cells = <1>;
>+ #size-cells = <1>;
>+ reg-names = "base", "csr", "ptp", "sgmii";
>+ reg = <0xfeb20000 0x10000>,
>+ <0xfeb36000 0x1000>,
>+ <0xfeb3c000 0x4000>,
>+ <0xfeb38000 0x400>;
>+ interrupt-parent = <&emac0>;
>+ #interrupt-cells = <1>;
>+ interrupts = <76 80>;
>+ interrupt-names = "emac_core0", "sgmii_irq";
>+ phy0: ethernet-phy@0 {
>+ compatible = "qcom,fsm9900-emac-phy";
>+ reg = <0>;
>+ }
If this is an external PHY, the expectation is that it will be hanging
off a MDIO bus controller, either the MDIO bus internal to the MAC, or
an external MDIO bus (separate register range).
So for starters, I forgot to delete the 'compatible' property from this
document. Its presence breaks of_mdiobus_child_is_phy().
If such a PHY node is provided, the expectation is that your Ethernet
MAC will have a phy-handle property and a phy-mode property to specify
how to connect to this external PHY, so in your specific case, better
remove the PHY from your example, or detail further how it should be done.
Something is odd about of_mdiobus_register().
This function scans child nodes to look for PHYs:
/* Loop over the child nodes and register a phy_device for each phy */
for_each_available_child_of_node(np, child) {
addr = of_mdio_parse_addr(&mdio->dev, child);
And in my driver, this works. However, later when I try to call
of_phy_find_device(), it fails. That's because of_phy_find_device()
wants the np of the child node. But the only way to get that is with a
phy-phandle property which I need to manually parse.
So what's the point of having of_mdiobus_register() parse child nodes,
if you need a phy-phandle pointer anyway?
>diff --git a/drivers/net/ethernet/qualcomm/Kconfig b/drivers/net/ethernet/qualcomm/Kconfig
>index a76e380..85b599f 100644
>--- a/drivers/net/ethernet/qualcomm/Kconfig
>+++ b/drivers/net/ethernet/qualcomm/Kconfig
>@@ -24,4 +24,15 @@ config QCA7000
> To compile this driver as a module, choose M here. The module
> will be called qcaspi.
>
>+config QCOM_EMAC
>+ tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
>+ select CRC32
select PHYLIB?
Ok.
>diff --git a/drivers/net/ethernet/qualcomm/Makefile b/drivers/net/ethernet/qualcomm/Makefile
>index 9da2d75..1b3a0ce 100644
>--- a/drivers/net/ethernet/qualcomm/Makefile
>+++ b/drivers/net/ethernet/qualcomm/Makefile
>@@ -4,3 +4,5 @@
>
> obj-$(CONFIG_QCA7000) += qcaspi.o
> qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o
>+
>+obj-$(CONFIG_QCOM_EMAC) += emac/
Since you have a check on CONFIG_QCOM_EMAC in emac/Makefile, you could
always recurse into that directory while building (use obj-y).
Obviously, having "obj-$(CONFIG_QCOM_EMAC)" in both Makefiles is
redundant, but wouldn't it make more sense to change
"obj-$(CONFIG_QCOM_EMAC)" to "obj-y" in
drivers/net/ethernet/qualcomm/emac/Makefile, so that I only recurse if
necessary?
>+static void emac_adjust_link(struct net_device *netdev)
>+{
>+ struct emac_adapter *adpt = netdev_priv(netdev);
>+ struct phy_device *phydev = netdev->phydev;
>+
>+ if (phydev->link)
>+ emac_mac_start(adpt);
>+ else
>+ emac_mac_stop(adpt);
This is really excessive here, you typically don't need to completely
stop your transmitter/receiver/DMA/what have you, just reprogram the MAC
with the appropriate link speed/duplex/pause parameters.
Yes, I realize that a lot of the reinit code in my driver is "heavy",
and that it could be optimized for specific situations. However, I'd
like to save that for another patch, because it would require me to
study the documentation and do extensive tests.
I can't tell you today whether emac_mac_start() is overkill for the
specific link change. For all I know, the hardware does require the TX
to stop before changing the link speed. Remember, the EMAC does have a
weird double-phy (one internal, one external).
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the
Code Aurora Forum, hosted by The Linux Foundation.
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
