Qualcomm regulator supports two power supply modes: HPM and LPM. Currently, the sdhci-msm.c driver does not set the load to adjust the current for eMMC and SD. If the regulator dont't set correct load in LPM state, it will lead to the inability to properly initialize eMMC and SD. Set the correct regulator current for eMMC and SD to ensure that the device can work normally even when the regulator is in LPM. Signed-off-by: Yuanjie Yang <quic_yuanjiey@xxxxxxxxxxx> --- Changes in v3: - Optimize the code logic and separate code for regulator vmmc and vqmmc - Rebase on tag: next-20241217 - Link to v2: https://lore.kernel.org/all/20241127095029.3918290-1-quic_yuanjiey@xxxxxxxxxxx/ Changes in v2: - Add enum msm_reg_type to optimize the code - Delete redundant emmc type judgment - Link to v1: https://lore.kernel.org/linux-arm-msm/20241122075048.2006894-1-quic_yuanjiey@xxxxxxxxxxx/ --- drivers/mmc/host/sdhci-msm.c | 64 ++++++++++++++++++++++++++++++++++-- 1 file changed, 62 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c index e00208535bd1..22811964ba61 100644 --- a/drivers/mmc/host/sdhci-msm.c +++ b/drivers/mmc/host/sdhci-msm.c @@ -134,9 +134,18 @@ /* Timeout value to avoid infinite waiting for pwr_irq */ #define MSM_PWR_IRQ_TIMEOUT_MS 5000 +/* Max load for eMMC Vdd supply */ +#define MMC_VMMC_MAX_LOAD_UA 570000 + /* Max load for eMMC Vdd-io supply */ #define MMC_VQMMC_MAX_LOAD_UA 325000 +/* Max load for SD Vdd supply */ +#define SD_VMMC_MAX_LOAD_UA 800000 + +/* Max load for SD Vdd-io supply */ +#define SD_VQMMC_MAX_LOAD_UA 22000 + #define msm_host_readl(msm_host, host, offset) \ msm_host->var_ops->msm_readl_relaxed(host, offset) @@ -1403,11 +1412,59 @@ static int sdhci_msm_set_pincfg(struct sdhci_msm_host *msm_host, bool level) return ret; } -static int sdhci_msm_set_vmmc(struct mmc_host *mmc) +static void msm_config_vmmc_regulator(struct mmc_host *mmc, bool hpm) +{ + int load; + + if (!mmc->card) { + regulator_set_mode(mmc->supply.vmmc, + hpm ? REGULATOR_MODE_NORMAL : REGULATOR_MODE_IDLE); + return; + } + + if (!mmc_card_mmc(mmc->card) && + !mmc_card_sd(mmc->card)) + return; + + if (mmc_card_mmc(mmc->card)) + load = MMC_VMMC_MAX_LOAD_UA; + else if (mmc_card_sd(mmc->card)) + load = SD_VMMC_MAX_LOAD_UA; + load = hpm ? load : 0; + + regulator_set_load(mmc->supply.vmmc, load); + + return; +} + +static void msm_config_vqmmc_regulator(struct mmc_host *mmc, bool hpm) +{ + int load; + + if (!mmc->card) { + regulator_set_mode(mmc->supply.vqmmc, + hpm ? REGULATOR_MODE_NORMAL : REGULATOR_MODE_IDLE); + return; + } + + if (!mmc_card_sd(mmc->card)) + return; + + load = hpm ? SD_VQMMC_MAX_LOAD_UA : 0; + + regulator_set_load(mmc->supply.vqmmc, load); + + return; +} + +static int sdhci_msm_set_vmmc(struct sdhci_msm_host *msm_host, + struct mmc_host *mmc, bool hpm) { if (IS_ERR(mmc->supply.vmmc)) return 0; + msm_config_vmmc_regulator(mmc, hpm); + return mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, mmc->ios.vdd); } @@ -1420,6 +1477,8 @@ static int msm_toggle_vqmmc(struct sdhci_msm_host *msm_host, if (msm_host->vqmmc_enabled == level) return 0; + msm_config_vqmmc_regulator(mmc, level); + if (level) { /* Set the IO voltage regulator to default voltage level */ if (msm_host->caps_0 & CORE_3_0V_SUPPORT) @@ -1642,7 +1701,8 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq) } if (pwr_state) { - ret = sdhci_msm_set_vmmc(mmc); + ret = sdhci_msm_set_vmmc(msm_host, mmc, + pwr_state & REQ_BUS_ON); if (!ret) ret = sdhci_msm_set_vqmmc(msm_host, mmc, pwr_state & REQ_BUS_ON); -- 2.34.1
