On 12/24/2024 12:27 AM, Dmitry Baryshkov wrote:
On Sun, Nov 24, 2024 at 07:02:48AM +0530, Krishna Chaitanya Chundru wrote:
On 11/15/2024 9:48 PM, Rob Herring wrote:
On Tue, Nov 12, 2024 at 08:31:33PM +0530, Krishna chaitanya chundru wrote:
Add binding describing the Qualcomm PCIe switch, QPS615,
which provides Ethernet MAC integrated to the 3rd downstream port
and two downstream PCIe ports.
Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
---
.../devicetree/bindings/pci/qcom,qps615.yaml | 205 +++++++++++++++++++++
1 file changed, 205 insertions(+)
diff --git a/Documentation/devicetree/bindings/pci/qcom,qps615.yaml b/Documentation/devicetree/bindings/pci/qcom,qps615.yaml
new file mode 100644
index 000000000000..e6a63a0bb0f3
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/qcom,qps615.yaml
@@ -0,0 +1,205 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/qcom,qps615.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm QPS615 PCIe switch
+
+maintainers:
+ - Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
+
+description: |
+ Qualcomm QPS615 PCIe switch has one upstream and three downstream
+ ports. The 3rd downstream port has integrated endpoint device of
+ Ethernet MAC. Other two downstream ports are supposed to connect
+ to external device.
+
+ The QPS615 PCIe switch can be configured through I2C interface before
+ PCIe link is established to change FTS, ASPM related entry delays,
+ tx amplitude etc for better power efficiency and functionality.
+
+properties:
+ compatible:
+ enum:
+ - pci1179,0623
+
+ reg:
+ maxItems: 1
+
+ i2c-parent:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: |
Don't need '|' if no formatting to preserve.
ack
+ A phandle to the parent I2C node and the slave address of the device
+ used to do configure qps615 to change FTS, tx amplitude etc.
+ items:
+ - description: Phandle to the I2C controller node
+ - description: I2C slave address
+
+ vdd18-supply: true
+
+ vdd09-supply: true
+
+ vddc-supply: true
+
+ vddio1-supply: true
+
+ vddio2-supply: true
+
+ vddio18-supply: true
+
+ reset-gpios:
+ maxItems: 1
+ description:
+ GPIO controlling the RESX# pin.
Is the PERST# or something else?
it is not PERST GPIO, it is similar to PERST in terms
of functionality which brings switch out from reset.
Do you have an actual PERST# on upstream facing port? Is it a separate
wire? Judging by the RB3 Gen2 this line is being used as PERST#
we had PERST# as a separate line. It has two inputs one is PERST# &
other one is RESX# gpio functionality wise both are similar.
+
+ qps615,axi-clk-freq-hz:
qps615 is not a vendor prefix.
+ description:
+ AXI clock rate which is internal bus of the switch
+ The switch only runs in two frequencies i.e 250MHz and 125MHz.
+ enum: [125000000, 250000000]
+
+allOf:
+ - $ref: "#/$defs/qps615-node"
+
+patternProperties:
+ "@1?[0-9a-f](,[0-7])?$":
You have 3 ports. So isn't this fixed and limited to 0-2?
sure I will change it to below as suggested
"@1?[0-3](,[0-1])?$"
Why do you still need '1?' ?
we want to represent integrated ethernet MAC also here and to represent
it we need '1' as it is multi function device. I will update the
description to reflect the same.
+ description: child nodes describing the internal downstream ports
+ the qps615 switch.
Please be consistent with starting after the ':' or on the next line.
And start with capital C.
ack
+ type: object
+ $ref: "#/$defs/qps615-node"
+ unevaluatedProperties: false
+
+$defs:
+ qps615-node:
+ type: object
+
+ properties:
+ qcom,l0s-entry-delay-ns:
+ description: Aspm l0s entry delay.
+
+ qcom,l1-entry-delay-ns:
+ description: Aspm l1 entry delay.
These should probably be common being standard PCIe things. Though, why
are they needed? I'm sure the timing is defined by the PCIe spec, so
they are not compliant?
Usually the firmware in the endpoints/switches should do this these
configurations. But the qps615 PCIe switch doesn't have any firmware
running to configure these. So the hardware exposes i2c interface to
configure these before link training.
If they are following the standard, why do you need to have them in the
DT? Can you hardcode thos evalues in the driver?
These values can be changed from platform to platform based upon the
different power goals and latency requirements so we can't have hard
coded values.
And even DWC controllers also provide provision to change these values
currently we are not using them. As bjorn suggested if we move these to
common pcie bindings these can be used in future by controller drivers also.
+
+ qcom,tx-amplitude-millivolt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Change Tx Margin setting for low power consumption.
+
+ qcom,no-dfe-support:
+ type: boolean
+ description: Disable DFE (Decision Feedback Equalizer), which mitigates
+ intersymbol interference and some reflections caused by impedance mismatches.
+
+ qcom,nfts:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Number of Fast Training Sequence (FTS) used during L0s to L0 exit
+ for bit and Symbol lock.
Also something common.
The problem I have with all these properties is you are using them on
both the upstream and downstream sides of the PCIe links. They belong in
either the device's node (downstream) or the bus's node (upstream).
This switch allows us to configure both upstream, downstream ports and
also embedded Ethernet port which is internal to the switch. These
properties are applicable for all of those.
+
+ allOf:
+ - $ref: /schemas/pci/pci-bus.yaml#
pci-pci-bridge.yaml is more specific and closer to what this device is.
I tried this now, I was getting warning saying the compatible
/local/mnt/workspace/skales/kobj/Documentation/devicetree/bindings/pci/qcom,qps615.example.dtb:
pcie@0,0: compatible: ['pci1179,0623'] does not contain items matching the
given schema
from schema $id: http://devicetree.org/schemas/pci/qcom,qps615.yaml#
/local/mnt/workspace/skales/kobj/Documentation/devicetree/bindings/pci/qcom,qps615.example.dtb:
pcie@0,0: Unevaluated properties are not allowed ('#address-cells',
'#size-cells', 'bus-range', 'device_type', 'ranges' were unexpected)
I think pci-pci-bridge is expecting the compatible string in this format
only "pciclass,0604".
I think the pci-pci-bridge schema requires to have "pciclass,0604" among
other compatibles. So you should be able to do something like:
compatible = "pci1179,0623", "pciclass,0604";
At least if follows PCI Bus Binding to Open Firmware document.
let us try this and come back.
+
+unevaluatedProperties: false
+
+required:
+ - vdd18-supply
+ - vdd09-supply
+ - vddc-supply
+ - vddio1-supply
+ - vddio2-supply
+ - vddio18-supply
+ - i2c-parent
+ - reset-gpios
+
+examples:
+ - |
+
+ #include <dt-bindings/gpio/gpio.h>
+
+ pcie {
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ bus-range = <0x01 0xff>;
+
+ pcie@0,0 {
+ compatible = "pci1179,0623";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ bus-range = <0x02 0xff>;
+
+ i2c-parent = <&qup_i2c 0x77>;
+
+ vdd18-supply = <&vdd>;
+ vdd09-supply = <&vdd>;
+ vddc-supply = <&vdd>;
+ vddio1-supply = <&vdd>;
+ vddio2-supply = <&vdd>;
+ vddio18-supply = <&vdd>;
+
+ reset-gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+
+ pcie@1,0 {
+ reg = <0x20800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x03 0xff>;
+
+ qcom,no-dfe-support;
+ };
+
+ pcie@2,0 {
+ reg = <0x21000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x04 0xff>;
+
+ qcom,nfts = <10>;
+ };
+
+ pcie@3,0 {
+ reg = <0x21800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x05 0xff>;
+
+ qcom,tx-amplitude-millivolt = <10>;
+ pcie@0,0 {
+ reg = <0x50000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
There's a 2nd PCI-PCI bridge?
This the embedded ethernet port which is as part of DSP3.
So is there an adidtional bus for that ethernet device?
yes for ethernet it has aditional bus assigned.
- Krishna Chaitanya.
+ ranges;
+
+ qcom,l1-entry-delay-ns = <10>;
+ };
+
+ pcie@0,1 {
+ reg = <0x50100 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+
+ qcom,l0s-entry-delay-ns = <10>;
+ };
What is this?
Ethernet endpoint is a multi function device which has 2 functions
This node represents 2nd node. I will update the description to
reflect the same.
- Krishna Chaitanya.
+ };
+ };
+ };
+ };
--
2.34.1
