On Fri, Dec 06, 2024 at 08:15:35PM +0530, Janaki Ramaiah Thota wrote:
>
>
> On 12/5/2024 4:29 AM, Dmitry Baryshkov wrote:
> > On Wed, Dec 04, 2024 at 06:47:04PM +0530, Janaki Ramaiah Thota wrote:
> > > Add a node for the PMU module of the WCN6750 present on the
> > > qcs6490-rb3gen board and assign its power outputs to the Bluetooth
> > > module.
> > >
> > > Signed-off-by: Janaki Ramaiah Thota <quic_janathot@xxxxxxxxxxx>
> > > ---
> > > arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 165 ++++++++++++++++++-
> > > 1 file changed, 164 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> > > index 27695bd54220..07650648214e 100644
> > > --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> > > +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
> > > @@ -1,6 +1,6 @@
> > > // SPDX-License-Identifier: BSD-3-Clause
> > > /*
> > > - * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
> > > + * Copyright (c) 2023-2024 Qualcomm Innovation Center, Inc. All rights reserved.
> > > */
> > > /dts-v1/;
> > > @@ -33,6 +33,7 @@
> > > aliases {
> > > serial0 = &uart5;
> > > + serial1 = &uart7;
> > > };
> > > chosen {
> > > @@ -217,6 +218,63 @@
> > > regulator-min-microvolt = <3700000>;
> > > regulator-max-microvolt = <3700000>;
> > > };
> > > +
> > > + wcn6750-pmu {
> > > + compatible = "qcom,wcn6750-pmu";
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&bt_en>;
> > > + vddaon-supply = <&vreg_s7b_0p972>;
> > > + vddasd-supply = <&vreg_l11c_2p8>;
> > > + vddpmu-supply = <&vreg_s7b_0p972>;
> > > + vddrfa0p8-supply = <&vreg_s7b_0p972>;
> > > + vddrfa1p2-supply = <&vreg_s8b_1p272>;
> > > + vddrfa1p7-supply = <&vreg_s1b_1p872>;
> > > + vddrfa2p2-supply = <&vreg_s1c_2p19>;
> > > +
> > > + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
> >
> > Doesn't WCN6750 also have SW_CTRL and wifi-enable pins?
> >
>
> For Bluetooth, these pins are not needed. We have verified Bluetooth
> functionality, and it is working fine.
You are describing the hardware (PMU), not "a part of the PMU for the
BT". Please check if there should be a wifi enable pin and adjust
accordingly.
--
With best wishes
Dmitry
