Re: [PATCH v2 09/22] usb: chipidea: Kick OTG state machine for AVVIS with vbus extcon

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Jul 07, 2016 at 03:21:00PM -0700, Stephen Boyd wrote:
> Force the OTG state machine to go forward when we're using an
> extcon for vbus detection. In this case, the controller may never
> raise an interrupt for AVVIS, so we need to simulate the event by
> toggling the appropriate OTG fsm bits and kicking the state
> machine again.
> 
> Cc: Peter Chen <peter.chen@xxxxxxx>
> Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Stephen Boyd <stephen.boyd@xxxxxxxxxx>
> ---
> 
> I think this was rejected last time around but I've kept it in the
> series to continue discussion on how we're supposed to be emulating
> vbus an id pin interrupts and the otgsc register.
> 
>  drivers/usb/chipidea/otg_fsm.c | 17 +++++++++++++++++
>  1 file changed, 17 insertions(+)
> 
> diff --git a/drivers/usb/chipidea/otg_fsm.c b/drivers/usb/chipidea/otg_fsm.c
> index de8e22ec3902..aab076fc4d82 100644
> --- a/drivers/usb/chipidea/otg_fsm.c
> +++ b/drivers/usb/chipidea/otg_fsm.c
> @@ -475,6 +475,14 @@ static void ci_otg_drv_vbus(struct otg_fsm *fsm, int on)
>  				return;
>  			}
>  		}
> +		/*
> +		 * Force state machine forward if we use extcon
> +		 * to detect vbus state (i.e. simulate AVVIS event)
> +		 */
> +		if (!IS_ERR(ci->platdata->vbus_extcon.edev)) {
> +			fsm->a_vbus_vld = 1;
> +			ci_otg_queue_work(ci);
> +		}
>  		/* Disable data pulse irq */
>  		hw_write_otgsc(ci, OTGSC_DPIE, 0);
>  
> @@ -486,6 +494,15 @@ static void ci_otg_drv_vbus(struct otg_fsm *fsm, int on)
>  
>  		fsm->a_bus_drop = 1;
>  		fsm->a_bus_req = 0;
> +		/*
> +		 * Force state machine forward if we use extcon
> +		 * to detect vbus state (i.e. simulate AVVIS event)
> +		 */
> +		if (!IS_ERR(ci->platdata->vbus_extcon.edev)) {
> +			fsm->a_vbus_vld = 0;
> +			fsm->b_conn = 0;
> +			ci_otg_queue_work(ci);
> +		}
>  	}
>  }
>  

Well, if we don't have a_valid, we can't know a_vbus_err state at
A device side if vbus is error (eg, less than 4.4v), and B device
will NOT be disconnect if vbus is still larger than BSV.

Do you really need OTG FSM? If you can pass the OTG test described at
Documentation/usb/chipidea.txt, I can accept it, I find the OTG
compliance test does not test ~a_vbus_vld either, see
otgeh_compliance_plan_1_2, ch6.7.12.2 Paths not tested.

-- 

Best Regards,
Peter Chen
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux